There seems to be some confusion surrounding three PHY interface modes, specifically 1000BASE-X, 2500BASE-X and SGMII. Add some documentation to phylib detailing precisely what these interface modes refer to. Signed-off-by: Russell King <rmk+kernel@xxxxxxxxxxxxxxx> --- This is in response to recent discussion, both public and private of recent attempts to convert some drivers to use phylink. This is to aid understanding the differences between these three phy link modes, specifically with respect to the "up-clocked" 2.5G variants. The 2.5G variants are the basic 1G variants but with the serdes link clocked 2.5 times faster; there are no bits in the control word that identify this over the standard rates. A serdes clocked 2.5x faster does not support the 1G/100M/10M speeds, but can only support 2.5G and (theoretically for SGMII) 250M/25M. In practice, the PHY data sheets I've read state that these slower speeds at the up-clocked link speed are not supported. It should be noted that we do not currently support 2.5G SGMII, but we do support 2.5G BASE-X PHY interface mode. Documentation/networking/phy.rst | 45 +++++++++++++++++++++++++++++++++++++++- 1 file changed, 44 insertions(+), 1 deletion(-) diff --git a/Documentation/networking/phy.rst b/Documentation/networking/phy.rst index 0dd90d7df5ec..a689966bc4be 100644 --- a/Documentation/networking/phy.rst +++ b/Documentation/networking/phy.rst @@ -202,7 +202,8 @@ the PHY/controller, of which the PHY needs to be aware. *interface* is a u32 which specifies the connection type used between the controller and the PHY. Examples are GMII, MII, -RGMII, and SGMII. For a full list, see include/linux/phy.h +RGMII, and SGMII. See "PHY interface mode" below. For a full +list, see include/linux/phy.h Now just make sure that phydev->supported and phydev->advertising have any values pruned from them which don't make sense for your controller (a 10/100 @@ -225,6 +226,48 @@ When you want to disconnect from the network (even if just briefly), you call phy_stop(phydev). This function also stops the phylib state machine and disables PHY interrupts. +PHY interface modes +=================== + +The PHY interface mode supplied in the phy_connect() family of functions +defines the initial operating mode of the PHY interface. This is not +guaranteed to remain constant; there are PHYs which dynamically change +their interface mode without software interaction depending on the +negotiation results. + +Some of the interface modes are described below: + +``PHY_INTERFACE_MODE_1000BASEX`` + This defines the 1000BASE-X single-lane serdes link as defined by the + 802.3 standard section 36. The link operates at a fixed bit rate of + 1.25Gbaud using a 10B/8B encoding scheme, resulting in an underlying + data rate of 1Gbps. Embedded in the data stream is a 16-bit control + word which is used to negotiate the duplex and pause modes with the + remote end. This does not include "up-clocked" variants such as 2.5Gbps + speeds (see below.) + +``PHY_INTERFACE_MODE_2500BASEX`` + This defines a variant of 1000BASE-X which is clocked 2.5 times faster, + than the 802.3 standard giving a fixed bit rate of 3.125Gbaud. + +``PHY_INTERFACE_MODE_SGMII`` + This is used for Cisco SGMII, which is a modification of 1000BASE-X + as defined by the 802.3 standard. The SGMII link consists of a single + serdes lane running at a fixed bit rate of 1.25Gbaud with 10B/8B + encoding. The underlying data rate is 1Gbps, with the slower speeds of + 100Mbps and 10Mbps being achieved through replication of each data symbol. + The 802.3 control word is re-purposed to send the negotiated speed and + duplex information from to the MAC, and for the MAC to acknowledge + receipt. This does not include "up-clocked" variants such as 2.5Gbps + speeds. + + Note: mismatched SGMII vs 1000BASE-X configuration on a link can + successfully pass data in some circumstances, but the 16-bit control + word will not be correctly interpreted, which may cause mismatches in + duplex, pause or other settings. This is dependent on the MAC and/or + PHY behaviour. + + Pause frames / flow control =========================== -- 2.7.4
