On Mon, Dec 17, 2018 at 08:53:21AM +0100, Uwe Kleine-König wrote: > On Sun, Dec 16, 2018 at 03:18:52PM +0100, Paul Cercueil wrote: > > Hi, > > > > Le ven. 14 déc. 2018 à 15:26, Uwe Kleine-König > > <u.kleine-koenig@xxxxxxxxxxxxxx> a écrit : > > > Hello, > > > > > > On Fri, Dec 14, 2018 at 02:50:20PM +0100, Linus Walleij wrote: > > > > On Thu, Dec 13, 2018 at 9:42 PM Uwe Kleine-König > > > > <u.kleine-koenig@xxxxxxxxxxxxxx> wrote: > > > > > [Adding Linus Walleij to Cc:] > > > > > On Thu, Dec 13, 2018 at 03:03:15PM +0100, Paul Cercueil wrote: > > > > > > Le jeu. 13 déc. 2018 à 10:24, Uwe Kleine-König > > > > > > <u.kleine-koenig@xxxxxxxxxxxxxx> a écrit : > > > > > > > On Wed, Dec 12, 2018 at 11:09:10PM +0100, Paul Cercueil wrote: > > > > > > > > The PWM in the JZ4725B works the same as in the JZ4740, > > > > > > > > except that it only has 6 channels available instead of > > > > > > > > 8. > > > > > > > > > > > > > > this driver is probed only from device tree? If yes, it > > > > > > > might be sensible to specify the number of PWMs there and > > > > > > > get it from there. > > > > > > > There doesn't seem to be a generic binding for that, but there are > > > > > > > several drivers that could benefit from it. (This is a bigger project > > > > > > > though and shouldn't stop your patch. Still more as it already got > > > > > > > Thierry's ack.) > > > > > > > > > > > > I think there needs to be a proper guideline, as there doesn't seem to be > > > > > > a consensus about this. I learned from emails with Rob and Linus (Walleij) > > > > > > that I should not have in devicetree what I can deduce from the compatible > > > > > > string. > > > > > > > > > > I understood them a bit differently. It is ok to deduce things from the > > > > > compatible string. But if you define a generic property (say) "num-pwms" > > > > > that is used uniformly in most bindings this is ok, too. (And then the > > > > > two different devices could use the same compatible.) > > > > > > > > > > An upside of the generic "num-pwms" property is that the pwm core could > > > > > sanity check pwm phandles before passing them to the hardware drivers. > > > > > > > > I don't know if this helps, but in GPIO we have "ngpios" which is > > > > used to augment an existing block as to the number of lines actually > > > > used with it. > > > > > > > > The typical case is that an ASIC engineer synthesize a block for > > > > 32 GPIOs but only 12 of them are routed to external pads. So > > > > we augment the behaviour of that driver to only use 12 of the > > > > 32 lines. > > > > > > > > I guess using the remaining 20 lines "works" in a sense but they > > > > have no practical use and will just bias electrons in the silicon > > > > for no use. > > > > > > This looks very similar to the case under discussion. > > > > > > > So if the PWM case is something similar, then by all means add > > > > num-pwms. > > > > > > .. or "npwms" to use the same nomenclature as the gpio binding? > > > > If we're going to do something like this, should it be the drivers or > > the core (within pwmchip_add) that checks for this "npwms" property? > > Of course this should be done in the core. The driver than can rely on > the validity of the index. But as I wrote before, this shouldn't stop > your patch from going in. > > But if Thierry agrees that this npmws (or num-pwms) is a good idea, it > would be great to start early to convert drivers. Do we actually need this? It seems like Paul's patch here properly derives the number of available PWMs from the compatible string, so I don't see what the extra num-pwms (or whatever) property would add. Thierry
Attachment:
signature.asc
Description: PGP signature
