On Friday, September 21, 2018 4:14:06 PM CEST Marek Szyprowski wrote: > Hi Janusz, > > > On 2018-09-21 12:51, Janusz Krzysztofik wrote: > > 2018-09-21 10:18 GMT+02:00, Marek Szyprowski <m.szyprowski@xxxxxxxxxxx>: > >> On 2018-09-20 18:21, Janusz Krzysztofik wrote: > >>> On Thursday, September 20, 2018 5:48:22 PM CEST Janusz Krzysztofik wrote: > >>>> On Thursday, September 20, 2018 12:11:48 PM CEST Marek Szyprowski wrote: > >>>>> On 2018-09-02 14:01, Janusz Krzysztofik wrote: > >>>>>> Certain GPIO descriptor arrays returned by gpio_get_array() may > >>>>>> contain > >>>>>> information on direct mapping of array members to pins of a single > >>>>>> GPIO > >>>>>> chip in hardware order. In such cases, bitmaps of values can be > >>>>>> passed > >>>>>> directly from/to the chip's .get/set_multiple() callbacks without > >>>>>> wasting time on iterations. > >>>>>> > >>>>>> Add respective code to gpiod_get/set_array_bitmap_complex() functions. > >>>>>> Pins not applicable for fast path are processed as before, skipping > >>>>>> over the 'fast' ones. > >>>>>> > >>>>>> Cc: Jonathan Corbet <corbet@xxxxxxx> > >>>>>> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@xxxxxxxxx> > >>>>> I've just noticed that this patch landed in today's linux-next. Sadly > >>>>> it > >>>>> breaks booting of Exynos5250-based Samsung Snow Chromebook (ARM 32bit, > >>>>> device-tree source arch/arm/boot/dts/exynos5250-snow.dts). > >>>>> > >>>>> Booting hangs after detecting MMC cards. Reverting this patch fixes the > >>>>> boot. I will try later to add some debugs and investigate it further > >>>>> what > >>>>> really happens when booting hangs. > >>>> Hi Marek, > >>>> > >>>> Thanks for reporting. Could you please try the following fix? > >>> Hi again, > >>> > >>> I realized the patch was not correct, j, not i, should be updated in > >>> second > >>> hunk. Please try the following one. > >>> > >>> Thanks, > >>> Janusz > >>> > >>> >From a919c504850f6cb40e8e81267a3a37537f7c4fd4 Mon Sep 17 00:00:00 2001 > >>> From: Janusz Krzysztofik <jmkrzyszt@xxxxxxxxx> > >>> Date: Thu, 20 Sep 2018 17:37:21 +0200 > >>> Subject: [PATCH] gpiolib: Fix bitmap index not updated > >>> While skipping fast path bits, bitmap index is not updated with next > >>> found zero bit position. Fix it. > >>> > >>> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@xxxxxxxxx> > >> This one also doesn't help. A quick compare of logs with this version and > >> a working system shows, that with your patch (and fix) there are no calls > >> to > >> gpx0-2 pin (which are a part of mmc pwrseq), what causes mmc failure. If > >> you need any more information (what kind of logs will help?), let me know. > > There is a debug message on array_info content available at the end of > > gpiod_get_array(), could you please activate it and post the message so > > we can understand better what is going on? > > With debug enabled on next-20180919: > [ 2.499153] pwrseq_simple mmc3_pwrseq: GPIO array info: chip=gpx0, > size=2, get_mask=2, set_mask=2, invert_mask=2 Looks good to me, i..e., in line with what one could expect. However, ... > On next-20180920 I get no this message and booting hangs. > > Same with next-20180920 + your second fix from this thread. > > I will try to debug this more on Monday. > > > On the other hand, I've had a look your device-tree configuration and > > it looks like that specific setup won't benefit from the fast bitmap path. > > You have pin 2 at position 0 and pin 1 at position 1 of the array. > > Hence, the fast bitmap path covers only pin 1, and pin 2 is processed > > by the old path with apparently buggy code for skipping over fast pins. > > > > As a temporary workaround, you could try to revert the order of pins in > > your dts file (pin 1 at position 0, pin 2 at 1) and the mmc pwrseq code > > should work for you again by taking the original old path, not skipping > > over fast pins. Results of such check may also help us to better > > understand and resolve the issue. > > Changing the order of mmc pwrseq gpio pins fixes boot hang. Not being able to discover more coding bugs in the code modified by the series, I'm wondering if the reason for the issue you are observing comes from the fact both pins are no longer manipulated together within a single .set_multiple() chip callback. I'm working on a fix which prevents from that. Thanks, Janusz
