On 4/16/2018 11:10 AM, Rob Herring wrote:
On Tue, Apr 10, 2018 at 11:32:06AM -0700, Jae Hyun Yoo wrote:
This commit adds a dt-bindings document of PECI adapter driver for Aspeed
AST24xx/25xx SoCs.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@xxxxxxxxxxxxxxx>
Reviewed-by: Haiyue Wang <haiyue.wang@xxxxxxxxxxxxxxx>
Reviewed-by: James Feist <james.feist@xxxxxxxxxxxxxxx>
Reviewed-by: Vernon Mauery <vernon.mauery@xxxxxxxxxxxxxxx>
Cc: Alan Cox <alan@xxxxxxxxxxxxxxx>
Cc: Andrew Jeffery <andrew@xxxxxxxx>
Cc: Andrew Lunn <andrew@xxxxxxx>
Cc: Andy Shevchenko <andriy.shevchenko@xxxxxxxxx>
Cc: Arnd Bergmann <arnd@xxxxxxxx>
Cc: Benjamin Herrenschmidt <benh@xxxxxxxxxxxxxxxxxxx>
Cc: Fengguang Wu <fengguang.wu@xxxxxxxxx>
Cc: Greg KH <gregkh@xxxxxxxxxxxxxxxxxxx>
Cc: Guenter Roeck <linux@xxxxxxxxxxxx>
Cc: Jason M Biils <jason.m.bills@xxxxxxxxxxxxxxx>
Cc: Jean Delvare <jdelvare@xxxxxxxx>
Cc: Joel Stanley <joel@xxxxxxxxx>
Cc: Julia Cartwright <juliac@xxxxxxxxxxxx>
Cc: Miguel Ojeda <miguel.ojeda.sandonis@xxxxxxxxx>
Cc: Milton Miller II <miltonm@xxxxxxxxxx>
Cc: Pavel Machek <pavel@xxxxxx>
Cc: Randy Dunlap <rdunlap@xxxxxxxxxxxxx>
Cc: Stef van Os <stef.van.os@xxxxxxxxxxxxxxxxxxxxxxxxx>
Cc: Sumeet R Pawnikar <sumeet.r.pawnikar@xxxxxxxxx>
---
.../devicetree/bindings/peci/peci-aspeed.txt | 60 ++++++++++++++++++++++
1 file changed, 60 insertions(+)
create mode 100644 Documentation/devicetree/bindings/peci/peci-aspeed.txt
diff --git a/Documentation/devicetree/bindings/peci/peci-aspeed.txt b/Documentation/devicetree/bindings/peci/peci-aspeed.txt
new file mode 100644
index 000000000000..4598bb8c20fa
--- /dev/null
+++ b/Documentation/devicetree/bindings/peci/peci-aspeed.txt
@@ -0,0 +1,60 @@
+Device tree configuration for PECI buses on the AST24XX and AST25XX SoCs.
+
+Required properties:
+- compatible : Should be "aspeed,ast2400-peci" or "aspeed,ast2500-peci"
+ - aspeed,ast2400-peci: Aspeed AST2400 family PECI
+ controller
+ - aspeed,ast2500-peci: Aspeed AST2500 family PECI
+ controller
+- reg : Should contain PECI controller registers location and
+ length.
+- #address-cells : Should be <1>.
+- #size-cells : Should be <0>.
+- interrupts : Should contain PECI controller interrupt.
+- clocks : Should contain clock source for PECI controller.
+ Should reference clkin.
+- clock_frequency : Should contain the operation frequency of PECI controller
+ in units of Hz.
+ 187500 ~ 24000000
This is the frequency of the bus or used to derive it? It would be
better to specify the bus frequency instead and have the driver
calculate its internal freq. And then use "bus-frequency" instead.
I agree with you. Actually, it is being used for operation frequency
setting of PECI controller module in SoC so it's different from the
meaning of "bus-frequency". I'll change it to "operation-frequency".
+
+Optional properties:
+- msg-timing-nego : Message timing negotiation period. This value will
+ determine the period of message timing negotiation to be
+ issued by PECI controller. The unit of the programmed
+ value is four times of PECI clock period.
+ 0 ~ 255 (default: 1)
+- addr-timing-nego : Address timing negotiation period. This value will
+ determine the period of address timing negotiation to be
+ issued by PECI controller. The unit of the programmed
+ value is four times of PECI clock period.
+ 0 ~ 255 (default: 1)
+- rd-sampling-point : Read sampling point selection. The whole period of a bit
+ time will be divided into 16 time frames. This value will
+ determine the time frame in which the controller will
+ sample PECI signal for data read back. Usually in the
+ middle of a bit time is the best.
+ 0 ~ 15 (default: 8)
+- cmd_timeout_ms : Command timeout in units of ms.
+ 1 ~ 60000 (default: 1000)
s/_/-/
Will fix it.
All these either need vendor prefixes or should be standard properties
for PECI adapters. I think probably the latter case. If so, the first
2 should probably be in units of clocks (not 4 clocks). And they should
then be documented in the common PECI binding doc.
So far I've checked that these are ASPEED PECI controller specific
properties so it should be listed in here.
+
+Example:
+ peci: peci@1e78b000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x1e78b000 0x60>;
No need to show this part in examples.
Got it. Will drop the part.
+
+ peci0: peci-bus@0 {
+ compatible = "aspeed,ast2500-peci";
+ reg = <0x0 0x60>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <15>;
+ clocks = <&clk_clkin>;
+ clock-frequency = <24000000>;
+ msg-timing-nego = <1>;
+ addr-timing-nego = <1>;
+ rd-sampling-point = <8>;
+ cmd-timeout-ms = <1000>;
+ };
+ };
--
2.16.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
