Re: [PATCH v4 1/6] dt-bindings: soc: qcom: Add device tree binding for GENI SE

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Mar 14, 2018 at 05:58:46PM -0600, Karthikeyan Ramasubramanian wrote:
> Add device tree binding support for the QCOM GENI SE driver.
> 
> Signed-off-by: Karthikeyan Ramasubramanian <kramasub@xxxxxxxxxxxxxx>
> Signed-off-by: Sagar Dharia <sdharia@xxxxxxxxxxxxxx>
> Signed-off-by: Girish Mahadevan <girishm@xxxxxxxxxxxxxx>
> ---
>  .../devicetree/bindings/soc/qcom/qcom,geni-se.txt  | 123 +++++++++++++++++++++
>  1 file changed, 123 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
> 
> diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
> new file mode 100644
> index 0000000..b71b5df
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
> @@ -0,0 +1,123 @@
> +Qualcomm Technologies, Inc. GENI Serial Engine QUP Wrapper Controller
> +
> +Generic Interface (GENI) based Qualcomm Universal Peripheral (QUP) wrapper
> +is a programmable module for supporting a wide range of serial interfaces
> +like UART, SPI, I2C, I3C, etc. A single QUP module can provide upto 8 Serial
> +Interfaces, using its internal Serial Engines. The GENI Serial Engine QUP
> +Wrapper controller is modeled as a node with zero or more child nodes each
> +representing a serial engine.
> +
> +Required properties:
> +- compatible:		Must be "qcom,geni-se-qup".
> +- reg:			Must contain QUP register address and length.
> +- clock-names:		Must contain "m-ahb" and "s-ahb".
> +- clocks:		AHB clocks needed by the device.
> +
> +Required properties if child node exists:
> +- #address-cells: 	Must be <1> for Serial Engine Address
> +- #size-cells: 		Must be <1> for Serial Engine Address Size
> +- ranges: 		Must be present
> +
> +Properties for children:
> +
> +A GENI based QUP wrapper controller node can contain 0 or more child nodes
> +representing serial devices.  These serial devices can be a QCOM UART, I2C
> +controller, SPI controller, or some combination of aforementioned devices.
> +Please refer below the child node definitions for the supported serial
> +interface protocols.
> +
> +Qualcomm Technologies Inc. GENI Serial Engine based I2C Controller
> +
> +Required properties:
> +- compatible:		Must be "qcom,geni-i2c".
> +- reg: 			Must contain QUP register address and length.
> +- interrupts: 		Must contain I2C interrupt.
> +- clock-names: 		Must contain "se".
> +- clocks: 		Serial engine core clock needed by the device.
> +- #address-cells:	Must be <1> for I2C device address.
> +- #size-cells:		Must be <0> as I2C addresses have no size component.
> +
> +Optional property:
> +- clock-frequency:	Desired I2C bus clock frequency in Hz.
> +			When missing default to 400000Hz.
> +
> +Child nodes should conform to I2C bus binding as described in i2c.txt.
> +
> +Qualcomm Technologies Inc. GENI Serial Engine based UART Controller
> +
> +Required properties:
> +- compatible:		Must be "qcom,geni-debug-uart".
> +- reg: 			Must contain UART register location and length.
> +- interrupts: 		Must contain UART core interrupts.
> +- clock-names:		Must contain "se".
> +- clocks:		Serial engine core clock needed by the device.
> +
> +Qualcomm Technologies Inc. GENI Serial Engine based SPI Controller
> +
> +Required properties:
> +- compatible:		Must contain "qcom,geni-spi".
> +- reg:			Must contain SPI register location and length.
> +- interrupts:		Must contain SPI controller interrupts.
> +- clock-names:		Must contain "se".
> +- clocks:		Serial engine core clock needed by the device.
> +- spi-max-frequency:	Specifies maximum SPI clock frequency, units - Hz.
> +- #address-cells:	Must be <1> to define a chip select address on
> +			the SPI bus.
> +- #size-cells:		Must be <0>.
> +
> +Optional property:
> +- qcom,rt:		Indicates if the framework worker thread for this
> +			controller device should have real-time priority.

Sounds like a Linux issue, not a DT property. Given you have no driver 
yet, I'd drop this for now at least. With that,

Reviewed-by: Rob Herring <robh@xxxxxxxxxx>

Rob
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux