On Tue, Feb 27, 2018 at 06:38:06PM -0700, Karthikeyan Ramasubramanian wrote:
> Add device tree binding support for the QCOM GENI SE driver.
>
> Signed-off-by: Karthikeyan Ramasubramanian <kramasub@xxxxxxxxxxxxxx>
> Signed-off-by: Sagar Dharia <sdharia@xxxxxxxxxxxxxx>
> Signed-off-by: Girish Mahadevan <girishm@xxxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/soc/qcom/qcom,geni-se.txt | 89 ++++++++++++++++++++++
> 1 file changed, 89 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
>
> diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
> new file mode 100644
> index 0000000..fe6a0c0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
> @@ -0,0 +1,89 @@
> +Qualcomm Technologies, Inc. GENI Serial Engine QUP Wrapper Controller
> +
> +Generic Interface (GENI) based Qualcomm Universal Peripheral (QUP) wrapper
> +is a programmable module for supporting a wide range of serial interfaces
> +like UART, SPI, I2C, I3C, etc. A single QUP module can provide upto 8 Serial
> +Interfaces, using its internal Serial Engines. The GENI Serial Engine QUP
> +Wrapper controller is modeled as a node with zero or more child nodes each
> +representing a serial engine.
> +
> +Required properties:
> +- compatible: Must be "qcom,geni-se-qup".
> +- reg: Must contain QUP register address and length.
> +- clock-names: Must contain "m-ahb" and "s-ahb".
> +- clocks: AHB clocks needed by the device.
> +
> +Required properties if child node exists:
> +- #address-cells: Must be <1> for Serial Engine Address
> +- #size-cells: Must be <1> for Serial Engine Address Size
> +- ranges: Must be present
> +
> +Properties for children:
> +
> +A GENI based QUP wrapper controller node can contain 0 or more child nodes
> +representing serial devices. These serial devices can be a QCOM UART, I2C
> +controller, spi controller, or some combination of aforementioned devices.
s/spi/SPI/
Where's the SPI binding?
> +Please refer below the child node definitions for the supported serial
> +interface protocols.
> +
> +Qualcomm Technologies Inc. GENI Serial Engine based I2C Controller
> +
> +Required properties:
> +- compatible: Must be "qcom,geni-i2c".
> +- reg: Must contain QUP register address and length.
> +- interrupts: Must contain I2C interrupt.
> +- clock-names: Must contain "se".
> +- clocks: Serial engine core clock needed by the device.
> +- #address-cells: Must be <1> for i2c device address.
> +- #size-cells: Must be <0> as i2c addresses have no size component.
> +
> +Optional property:
> +- clock-frequency: Desired I2C bus clock frequency in Hz.
> + When missing default to 400000Hz.
> +
> +Child nodes should conform to i2c bus binding as described in i2c.txt.
> +
> +Qualcomm Technologies Inc. GENI Serial Engine based UART Controller
> +
> +Required properties:
> +- compatible: Must be "qcom,geni-debug-uart".
> +- reg: Must contain UART register location and length.
> +- interrupts: Must contain UART core interrupts.
> +- clock-names: Must contain "se".
> +- clocks: Serial engine core clock needed by the device.
> +
> +Example:
> + geniqup@8c0000 {
> + compatible = "qcom,geni-se-qup";
> + reg = <0x8c0000 0x6000>;
> + clock-names = "m-ahb", "s-ahb";
> + clocks = <&clock_gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
> + <&clock_gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + i2c0: i2c@a94000 {
> + compatible = "qcom,geni-i2c";
> + reg = <0xa94000 0x4000>;
> + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "se";
> + clocks = <&clock_gcc GCC_QUPV3_WRAP0_S5_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_1_i2c_5_active>;
> + pinctrl-1 = <&qup_1_i2c_5_sleep>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + uart0: serial@a88000 {
> + compatible = "qcom,geni-debug-uart";
> + reg = <0xa88000 0x7000>;
> + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "se";
> + clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qup_1_uart_3_active>;
> + pinctrl-1 = <&qup_1_uart_3_sleep>;
> + };
> + }
> --
> Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
>
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
