On Tue, Apr 11, 2017 at 02:32:18PM -0700, John Muir wrote: > v2: > - Fixup based on comments. While you should have a commit msg here, the patch versioning goes below the '---'. This history is not too useful either. You should describe what you changed so reviewers don't have to go find the previous versions. I may remember reviewing a patch, but I likely don't remember what I said. > > Signed-off-by: John Muir <john@xxxxxxxxx> > --- > .../devicetree/bindings/hwmon/max31760.txt | 72 ++++++++++++++++++++++ > 1 file changed, 72 insertions(+) > create mode 100644 Documentation/devicetree/bindings/hwmon/max31760.txt > > diff --git a/Documentation/devicetree/bindings/hwmon/max31760.txt b/Documentation/devicetree/bindings/hwmon/max31760.txt > new file mode 100644 > index 000000000000..760fdf0b55e0 > --- /dev/null > +++ b/Documentation/devicetree/bindings/hwmon/max31760.txt > @@ -0,0 +1,72 @@ > +MAX31760 fan controller > +----------------------- > + > +This device supports I2C only. Fan sub-nodes must be defined in order to enable > +the fan tachometer input. See also the datasheet: > +https://datasheets.maximintegrated.com/en/ds/MAX31760.pdf > + > +Required node properties: > + - compatible: "maxim,max31760" > + - reg: The I2C address of the device. This is 0x50 - 0x57 depending on the > + hardware configuration. > + - #address-cells: Must be 1. > + - #size-cells: Must be 0. > + > +Optional node properties: > + - maxim,fan-fail-full-only: Boolean; Assert a fan failure only when the PWM is > + at 100%. > + - maxim,fan-rd-signal: Boolean; Fans provide a rotation detection (RD) signal > + instead of generating square-wave pulses. > + - maxim,fan-rd-polarity-high: Boolean; RD is high when the fan is running, not > + low. Only relevant when fan-rd-signal is true. > + - maxim,fan-signal-enabled: Boolean; Externally driving FF/FS low should force > + PWM output to 100%. > + - maxim,fan-spin-up-enabled: Boolean; For fan startup set the PWM to 100% until > + tach is detected or two seconds have passed before reducing to the target > + value. > + - maxim,pwm-polarity-negative: Boolean; 100% PWM is when PWM is low, not high. > + - maxim,pwm-pulse-stretch-enabled: Boolean; Enable PWM pulse stretching. > + - maxim,pwm-zero-fan-can-fail: Boolean; Enable fan failure detection while > + ramping to 0% PWM. > + > +Fan sub-nodes must be present in order to enable the fan. > + > +Required fan sub-node properties: > + - reg: Fan address. Must be <0x00> or <0x01>. > + > +Optional fan sub-node properties: > + - label: String; Assigned to the hwmon fanX_label property. > + > +Temperature sub-nodes are optional. > + > +Required temp sub-node properties: > + - reg: Temperature sensor address. Must be <0x00> or <0x01>. > + > +Optional temp sub-node properties: > + - label: String; Assigned to the hwmon tempX_label property. > + - ideality: For temperature node with reg 1 only: Set ideality factor for the This too needs a maxim prefix. > + remote temperature sensor. Integer with range 0 to 63, representing a > + multiplication factor of 0.9844 to 1.0489. Default: 24 (1.0080). > + > +Example: > + max31760@50 { > + compatible = "maxim,max31760"; > + reg = <0x50>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + maxim,fan-spin-up-enabled; > + > + fan@0 { > + reg = <0x00>; > + label = "Left"; > + }; > + fan@1 { > + reg = <0x01>; > + label = "Right"; > + }; > + temp@1 { > + reg = <0x01>; > + label = "CPU"; > + }; > + }; > -- > 2.12.2.715.g7642488e1d-goog > -- To unsubscribe from this list: send the line "unsubscribe linux-doc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
