On Fri, Mar 10, 2017 at 05:53:50PM -0800, Jaghathiswari Rankappagounder Natarajan wrote:
> This binding provides interface for adding values related to ASPEED
> AST2400/2500 PWM and Fan tach controller support.
> The PWM controller can support upto 8 PWM output ports.
> The Fan tach controller can support upto 16 tachometer inputs.
>
> Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu@xxxxxxxxxx>
> ---
> v4:
> - Used 'reg'
>
> v3:
> - Made the structure more common
>
> v2:
> - Removed '_' in node and property names
> - Gave some explanation for the properties used
>
> .../devicetree/bindings/hwmon/aspeed-pwm-tacho.txt | 86 ++++++++++++++++++++++
> 1 file changed, 86 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt
>
> diff --git a/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt b/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt
> new file mode 100644
> index 000000000000..0dfd2841ace3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt
> @@ -0,0 +1,86 @@
> +ASPEED AST2400/AST2500 PWM and Fan Tacho controller device driver
> +
> +The ASPEED PWM controller can support upto 8 PWM outputs. The ASPEED Fan Tacho
> +controller can support upto 16 Fan tachometer inputs.
> +
> +There can be upto 8 fans supported. Each fan can have one PWM output and
> +one/two Fan tach inputs.
> +
> +Required properties for pwm-tacho node:
> +- #address-cells : should be 1.
> +
> +- #size-cells : should be 1.
> +
> +- reg : address and length of the register set for the device.
> +
> +- pinctrl-names : a pinctrl state named "default" must be defined.
> +
> +- pinctrl-0 : phandle referencing pin configuration of the PWM ports.
> +
> +- compatible : should be "aspeed,aspeed2400-pwm-tacho" for AST2400 or
> + "aspeed,aspeed2500-pwm-tacho" for AST2500.
> +
> +- clocks : a fixed clock providing input clock frequency(PWM
> + and Fan Tach clock)
> +
> +fan subnode format:
> +===================
> +Under fan subnode there can upto 8 child nodes, with each child node
> +representing a fan. If there are 8 fans each fan can have one PWM port and
> +one/two Fan tach inputs.
> +
> +Required properties for each child node:
> +- reg : should specify PWM source port.
> + integer value in the range 0 to 7 with 0 indicating PWM port A and
> + 7 indicating PWM port H.
> +
> + Atleast one tach subnode is required. Each tach subnode represents a fan
> + tach input.
> + tach subnode format:
> + --------------------
> + Required properties for each child node:
> + - fan-ctrl-gpios : should specify the tachometer input GPIO pin on the hardware.
> + Fan Tachometer function can only work when GPIO is in
> + ”input mode”.
As I mentioned on the last version, this sounds like pin-muxing, not
actual GPIO usage.
> +
> + - fan-tach-ch : should specify the Fan tach input channel.
> + integer value in the range 0 through 15, with 0 indicating
> + Fan tach channel 0 and 15 indicating Fan tach channel 15.
These 2 also need aspeed vendor prefixes.
This could become a property under the fan node as a list of tach
channels if fan-ctrl-gpios goes away.
> +
> +Examples:
> +
> +pwmtachofixedclk: fixedclk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <24000000>;
> +}
> +
> +pwmtacho: pwmtachocontroller@1e786000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0x1E786000 0x1000>;
> + compatible = "aspeed,aspeed2500-pwm-tacho";
> + clocks = <&pwmtachofixedclk>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default>;
> +
> + fan0 {
fan@0
> + reg = /bits/ 8 <0x00>;
reg is 32-bits.
> + tach0 {
> + fan-ctrl-gpios = <&gpio ASPEED_GPIO(O, 0) GPIO_ACTIVE_HIGH>;
> + fan-tach-ch = /bits/ 8 <0x00>;
> + };
> + };
> +
> + fan1 {
fan@1
> + reg = /bits/ 8 <0x01>;
> + tach0 {
> + fan-ctrl-gpios = <&gpio ASPEED_GPIO(O, 1) GPIO_ACTIVE_HIGH>;
> + fan-tach-ch = /bits/ 8 <0x01>;
> + };
> + tach1 {
> + fan-ctrl-gpios = <&gpio ASPEED_GPIO(O, 2) GPIO_ACTIVE_HIGH>;
> + fan-tach-ch = /bits/ 8 <0x02>;
> + };
> + };
> +};
> --
> 2.12.0.246.ga2ecc84866-goog
>
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
