On 2017-01-27 20:50, Rob Herring wrote: > On Wed, Jan 18, 2017 at 04:57:12PM +0100, Peter Rosin wrote: >> Analog Devices ADG792A/G is a triple 4:1 mux. >> >> Acked-by: Jonathan Cameron <jic23@xxxxxxxxxx> >> Signed-off-by: Peter Rosin <peda@xxxxxxxxxx> >> --- >> .../devicetree/bindings/mux/mux-adg792a.txt | 79 ++++++++++++++++++++++ >> 1 file changed, 79 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/mux/mux-adg792a.txt >> >> diff --git a/Documentation/devicetree/bindings/mux/mux-adg792a.txt b/Documentation/devicetree/bindings/mux/mux-adg792a.txt >> new file mode 100644 >> index 000000000000..0b26dd11f070 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/mux/mux-adg792a.txt >> @@ -0,0 +1,79 @@ >> +Bindings for Analog Devices ADG792A/G Triple 4:1 Multiplexers >> + >> +Required properties: >> +- compatible : "adi,adg792a" or "adi,adg792g" >> +- #mux-control-cells : <0> if parallel, or <1> if not. >> +* Standard mux-controller bindings as decribed in mux-controller.txt >> + >> +Optional properties for ADG792G: >> +- gpio-controller : if present, #gpio-cells below is required. >> +- #gpio-cells : should be <2> >> + - First cell is the GPO line number, i.e. 0 or 1 >> + - Second cell is used to specify active high (0) >> + or active low (1) >> + >> +Optional properties: >> +- adi,parallel : if present, the three muxes are bound together with a single >> + mux controller, controlling all three muxes in parallel. > > Can't this be implied by #mux-control-cells == 0? Right, good point! I'll drop adi,parallel. >> +- adi,idle-state : if present, array of 2-tuples with mux controller number >> + and state that mux controllers will have when idle. States 0 through 3 >> + correspond to signals A through D in the datasheet. >> +- adi,idle-high-impedance : if present, array of mux controller numbers that >> + should be in the disconnected high-impedance state when idle. > > Perhaps combine these 2 to a common idle-state with the index being the > mux controller number and a value of -1 (or 4) being hi-Z. At one point [1] I had a straight array for the mux controllers with state 4 being hi-Z and state 5 being the default "leave mux as-is on release", but Jonathan didn't like magic numbers. Can you please read the follow-ups to the referenced mail for some background, and then pick out the most suitable color for me to paint with? :-) [1] https://lkml.org/lkml/2016/11/30/110 >> + >> +Mux controller states 0 through 3 correspond to signals A through D in the >> +datasheet. If a mux controller is mentioned in neither adi,idle-state nor >> +adi,idle-high-impedance it is left in its previously selected state when idle. >> + >> +Example: >> + >> + /* >> + * Three independent mux controllers (of which one is used). >> + * Mux 0 is disconnected when idle, mux 1 idles with signal C >> + * and mux 2 idles with signal A. >> + */ >> + &i2c0 { >> + mux: adg792a@50 { > > mux-controller@50 Yep. Hmm, where have I seen that before? :-) Cheers, peda >> + compatible = "adi,adg792a"; >> + reg = <0x50>; >> + #mux-control-cells = <1>; >> + >> + adi,idle-high-impedance = <0>; >> + adi,idle-state = <1 2>, <2 0>; >> + }; >> + }; >> + >> + adc-mux { >> + compatible = "io-channel-mux"; >> + io-channels = <&adc 0>; >> + io-channel-names = "parent"; >> + >> + mux-controls = <&mux 1>; >> + >> + channels = "sync-1", "", "out"; >> + }; >> + >> + >> + /* >> + * Three parallel muxes with one mux controller, useful e.g. if >> + * the adc is differential, thus needing two signals to be muxed >> + * simultaneously for correct operation. >> + */ >> + &i2c0 { >> + pmux: adg792a@50 { >> + compatible = "adi,adg792a"; >> + reg = <0x50>; >> + #mux-control-cells = <0>; >> + adi,parallel; >> + }; >> + }; >> + >> + diff-adc-mux { >> + compatible = "io-channel-mux"; >> + io-channels = <&adc 0>; >> + io-channel-names = "parent"; >> + >> + mux-controls = <&pmux>; >> + >> + channels = "sync-1", "", "out"; >> + }; >> -- >> 2.1.4 >> >> -- >> To unsubscribe from this list: send the line "unsubscribe devicetree" in >> the body of a message to majordomo@xxxxxxxxxxxxxxx >> More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-doc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
