Hi,
On 23-11-16 15:25, Chen-Yu Tsai wrote:
On Wed, Nov 23, 2016 at 3:59 PM, Maxime Ripard
<maxime.ripard@xxxxxxxxxxxxxxxxxx> wrote:
Hi,
On Tue, Nov 22, 2016 at 12:24:21AM +0800, Icenowy Zheng wrote:
There's a Allwinner's XR819 SDIO Wi-Fi module soldered on the board of
Orange Pi Zero, which used a dedicated regulator to power.
Add the device tree node of the regulator, the enable gpio (with
mmc-pwrseq) and the sdio controller.
There's a out-of-tree driver tested to work with this device tree.
Signed-off-by: Icenowy Zheng <icenowy@xxxxxxxx>
---
New patch in the patchset, since a out-of-tree working xradio driver is done.
If there is any problem in this patch, it can be omitted.
No particular problem with this one, however it can and should be
merged with the previous one.
Minor comments below though.
arch/arm/boot/dts/sun8i-h2plus-orangepi-zero.dts | 42 ++++++++++++++++++++++++
1 file changed, 42 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-h2plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2plus-orangepi-zero.dts
index b428e47..39cac26 100644
--- a/arch/arm/boot/dts/sun8i-h2plus-orangepi-zero.dts
+++ b/arch/arm/boot/dts/sun8i-h2plus-orangepi-zero.dts
@@ -79,6 +79,24 @@
gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>;
};
};
+
+ reg_vcc_wifi: reg_vcc_wifi {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc_wifi_pin_opi0>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+ enable-active-high;
+ gpio = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_pwrseq_pin_opi0>;
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
+ };
};
&ehci1 {
@@ -95,6 +113,20 @@
status = "okay";
};
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_vcc_wifi>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&mmc1_pins_a {
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
This should be bias-pull-up.
IIRC I already added this for _all_ existing mmc pinmux settings?
+};
+
&ohci1 {
status = "okay";
};
@@ -104,6 +136,11 @@
pins = "PA17";
function = "gpio_out";
};
+
+ vcc_wifi_pin_opi0: vcc_wifi_pin@0 {
+ allwinner,pins = "PA20";
This should be pins
+ allwinner,function = "gpio_out";
This should be function
+ };
};
&r_pio {
@@ -111,6 +148,11 @@
pins = "PL10";
function = "gpio_out";
};
+
+ wifi_pwrseq_pin_opi0: wifi_pwrseq_pin@0 {
+ allwinner,pins = "PL7";
+ allwinner,function = "gpio_out";
And same thing here.
Might we do away with the pinmux for gpio pins tradition?
Recent patches I've sent all omit them.
I'm in favor of doing away with them, except there were
we need to configure bias / strength.
Regards,
Hans
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
