Re: [PATCH 3/3] ARM: dts: sunxi: add support for Orange Pi Zero board

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

On Sat, Nov 12, 2016 at 12:46:54AM +0800, Icenowy Zheng wrote:
> Orange Pi Zero is a board that came with the new Allwinner H2+ SoC.
> 
> Add a device tree file for it.
> 
> As there's still no mainline-compatible driver for the SDIO WLAN card on
> board (a new card by Allwinner), the mmc1 controller is not enabled yet.
> 
> Signed-off-by: Icenowy Zheng <icenowy@xxxxxxxx>
> ---
>  arch/arm/boot/dts/Makefile                       |   1 +
>  arch/arm/boot/dts/sun8i-h2plus-orangepi-zero.dts | 148 +++++++++++++++++++++++
>  2 files changed, 149 insertions(+)
>  create mode 100644 arch/arm/boot/dts/sun8i-h2plus-orangepi-zero.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index befcd26..9843fb0 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -818,6 +818,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
>  	sun8i-a33-sinlinx-sina33.dtb \
>  	sun8i-a83t-allwinner-h8homlet-v2.dtb \
>  	sun8i-a83t-cubietruck-plus.dtb \
> +	sun8i-h2plus-orangepi-zero.dtb \
>  	sun8i-h3-bananapi-m2-plus.dtb \
>  	sun8i-h3-nanopi-neo.dtb \
>  	sun8i-h3-orangepi-2.dtb \
> diff --git a/arch/arm/boot/dts/sun8i-h2plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2plus-orangepi-zero.dts
> new file mode 100644
> index 0000000..581f56e
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-h2plus-orangepi-zero.dts
> @@ -0,0 +1,148 @@
> +/*
> + * Copyright (C) 2016 Icenowy Zheng <icenowy@xxxxxxxx>
> + *
> + * Based on sun8i-h3-orangepi-one.dts, which is:
> + *   Copyright (C) 2016 Hans de Goede <hdegoede@xxxxxxxxxx>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun8i-h2plus.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/pinctrl/sun4i-a10.h>
> +
> +/ {
> +	model = "Xunlong Orange Pi Zero";
> +	compatible = "xunlong,orangepi-zero", "allwinner,sun8i-h2plus",
> +		     "allwinner,sun8i-h3";

You don't need the H3 compatible here.

> +
> +	aliases {
> +		serial0 = &uart0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&leds_opi0>, <&leds_r_opi0>;
> +
> +		pwr_led {
> +			label = "orangepi:green:pwr";
> +			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
> +			default-state = "on";
> +		};
> +
> +		status_led {
> +			label = "orangepi:red:status";
> +			gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>;
> +		};
> +	};
> +};
> +
> +&ehci1 {
> +	status = "okay";
> +};
> +
> +&mmc0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
> +	vmmc-supply = <&reg_vcc3v3>;
> +	bus-width = <4>;
> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
> +	cd-inverted;
> +	status = "okay";
> +};
> +
> +&ohci1 {
> +	status = "okay";
> +};
> +
> +&pio {
> +	leds_opi0: led_pins@0 {
> +		allwinner,pins = "PA17";
> +		allwinner,function = "gpio_out";
> +		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +	};
> +};
> +
> +&r_pio {
> +	leds_r_opi0: led_pins@0 {
> +		allwinner,pins = "PL10";
> +		allwinner,function = "gpio_out";
> +		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;

You can drop the drive and pull properties, and could you use the
generic pins and function properties for those nodes?

> +	};
> +};
> +
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_pins_a>;
> +	status = "okay";
> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart1_pins>;
> +	status = "disabled";
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart2_pins>;
> +	status = "disabled";
> +};
> +
> +&uart3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart3_pins>;
> +	status = "disabled";
> +};

I'm guessing that those UART are exposed on headers?

> +
> +&usbphy {
> +	/* USB VBUS is always on */

You can put the always on regulators (I'm guessing reg_vcc5v0 ?) here.

> +	status = "okay";
> +};

Thanks,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux