- Add a document title;
- use quote blocks where needed;
- convert parameters to a nested table;
- use monotonic fonts for config options and file names;
- adjust whitespaces and blank lines;
- replace _foo_ by **foo**;
- add it to the user's book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@xxxxxxxxxxxxxxxx>
---
Documentation/parport.txt | 268 ++++++++++++++++++++++++----------------------
1 file changed, 138 insertions(+), 130 deletions(-)
diff --git a/Documentation/parport.txt b/Documentation/parport.txt
index c208e4366c03..3273ce79f9e3 100644
--- a/Documentation/parport.txt
+++ b/Documentation/parport.txt
@@ -1,15 +1,18 @@
-The `parport' code provides parallel-port support under Linux. This
+Parport
++++++++
+
+The ``parport`` code provides parallel-port support under Linux. This
includes the ability to share one port between multiple device
drivers.
-You can pass parameters to the parport code to override its automatic
+You can pass parameters to the ``parport`` code to override its automatic
detection of your hardware. This is particularly useful if you want
to use IRQs, since in general these can't be autoprobed successfully.
-By default IRQs are not used even if they _can_ be probed. This is
+By default IRQs are not used even if they **can** be probed. This is
because there are a lot of people using the same IRQ for their
parallel port and a sound card or network card.
-The parport code is split into two parts: generic (which deals with
+The ``parport`` code is split into two parts: generic (which deals with
port-sharing) and architecture-dependent (which deals with actually
using the port).
@@ -17,21 +20,21 @@ using the port).
Parport as modules
==================
-If you load the parport code as a module, say
+If you load the `parport`` code as a module, say::
# insmod parport
-to load the generic parport code. You then must load the
-architecture-dependent code with (for example):
+to load the generic ``parport`` code. You then must load the
+architecture-dependent code with (for example)::
# insmod parport_pc io=0x3bc,0x378,0x278 irq=none,7,auto
-to tell the parport code that you want three PC-style ports, one at
+to tell the ``parport`` code that you want three PC-style ports, one at
0x3bc with no IRQ, one at 0x378 using IRQ 7, and one at 0x278 with an
-auto-detected IRQ. Currently, PC-style (parport_pc), Sun `bpp',
+auto-detected IRQ. Currently, PC-style (``parport_pc``), Sun ``bpp``,
Amiga, Atari, and MFC3 hardware is supported.
-PCI parallel I/O card support comes from parport_pc. Base I/O
+PCI parallel I/O card support comes from ``parport_pc``. Base I/O
addresses should not be specified for supported PCI cards since they
are automatically detected.
@@ -40,151 +43,154 @@ modprobe
--------
If you use modprobe , you will find it useful to add lines as below to a
-configuration file in /etc/modprobe.d/ directory:.
+configuration file in /etc/modprobe.d/ directory::
alias parport_lowlevel parport_pc
options parport_pc io=0x378,0x278 irq=7,auto
-modprobe will load parport_pc (with the options "io=0x378,0x278 irq=7,auto")
-whenever a parallel port device driver (such as lp) is loaded.
+modprobe will load ``parport_pc`` (with the options ``io=0x378,0x278 irq=7,auto``)
+whenever a parallel port device driver (such as ``lp``) is loaded.
Note that these are example lines only! You shouldn't in general need
-to specify any options to parport_pc in order to be able to use a
+to specify any options to ``parport_pc`` in order to be able to use a
parallel port.
Parport probe [optional]
--------------
+------------------------
-In 2.2 kernels there was a module called parport_probe, which was used
+In 2.2 kernels there was a module called ``parport_probe``, which was used
for collecting IEEE 1284 device ID information. This has now been
enhanced and now lives with the IEEE 1284 support. When a parallel
port is detected, the devices that are connected to it are analysed,
-and information is logged like this:
+and information is logged like this::
parport0: Printer, BJC-210 (Canon)
-The probe information is available from files in /proc/sys/dev/parport/.
+The probe information is available from files in ``/proc/sys/dev/parport/``.
Parport linked into the kernel statically
=========================================
-If you compile the parport code into the kernel, then you can use
+If you compile the ``parport`` code into the kernel, then you can use
kernel boot parameters to get the same effect. Add something like the
-following to your LILO command line:
+following to your LILO command line::
parport=0x3bc parport=0x378,7 parport=0x278,auto,nofifo
-You can have many `parport=...' statements, one for each port you want
-to add. Adding `parport=0' to the kernel command-line will disable
-parport support entirely. Adding `parport=auto' to the kernel
-command-line will make parport use any IRQ lines or DMA channels that
+You can have many ``parport=...`` statements, one for each port you want
+to add. Adding ``parport=0`` to the kernel command-line will disable
+parport support entirely. Adding ``parport=auto`` to the kernel
+command-line will make ``parport`` use any IRQ lines or DMA channels that
it auto-detects.
Files in /proc
==============
-If you have configured the /proc filesystem into your kernel, you will
-see a new directory entry: /proc/sys/dev/parport. In there will be a
+If you have configured the ``/proc`` filesystem into your kernel, you will
+see a new directory entry: ``/proc/sys/dev/parport``. In there will be a
directory entry for each parallel port for which parport is
configured. In each of those directories are a collection of files
describing that parallel port.
-The /proc/sys/dev/parport directory tree looks like:
+The ``/proc/sys/dev/parport`` directory tree looks like::
-parport
-|-- default
-| |-- spintime
-| `-- timeslice
-|-- parport0
-| |-- autoprobe
-| |-- autoprobe0
-| |-- autoprobe1
-| |-- autoprobe2
-| |-- autoprobe3
-| |-- devices
-| | |-- active
-| | `-- lp
-| | `-- timeslice
-| |-- base-addr
-| |-- irq
-| |-- dma
-| |-- modes
-| `-- spintime
-`-- parport1
- |-- autoprobe
- |-- autoprobe0
- |-- autoprobe1
- |-- autoprobe2
- |-- autoprobe3
- |-- devices
- | |-- active
- | `-- ppa
- | `-- timeslice
- |-- base-addr
- |-- irq
- |-- dma
- |-- modes
- `-- spintime
+ parport
+ |-- default
+ | |-- spintime
+ | `-- timeslice
+ |-- parport0
+ | |-- autoprobe
+ | |-- autoprobe0
+ | |-- autoprobe1
+ | |-- autoprobe2
+ | |-- autoprobe3
+ | |-- devices
+ | | |-- active
+ | | `-- lp
+ | | `-- timeslice
+ | |-- base-addr
+ | |-- irq
+ | |-- dma
+ | |-- modes
+ | `-- spintime
+ `-- parport1
+ |-- autoprobe
+ |-- autoprobe0
+ |-- autoprobe1
+ |-- autoprobe2
+ |-- autoprobe3
+ |-- devices
+ | |-- active
+ | `-- ppa
+ | `-- timeslice
+ |-- base-addr
+ |-- irq
+ |-- dma
+ |-- modes
+ `-- spintime
+======================= =======================================================
+File Contents
+======================= =======================================================
+``devices/active`` A list of the device drivers using that port. A "+"
+ will appear by the name of the device currently using
+ the port (it might not appear against any). The
+ string "none" means that there are no device drivers
+ using that port.
-File: Contents:
+``base-addr`` Parallel port's base address, or addresses if the port
+ has more than one in which case they are separated
+ with tabs. These values might not have any sensible
+ meaning for some ports.
-devices/active A list of the device drivers using that port. A "+"
- will appear by the name of the device currently using
- the port (it might not appear against any). The
- string "none" means that there are no device drivers
- using that port.
+``irq`` Parallel port's IRQ, or -1 if none is being used.
-base-addr Parallel port's base address, or addresses if the port
- has more than one in which case they are separated
- with tabs. These values might not have any sensible
- meaning for some ports.
+``dma`` Parallel port's DMA channel, or -1 if none is being
+ used.
-irq Parallel port's IRQ, or -1 if none is being used.
+``modes`` Parallel port's hardware modes, comma-separated,
+ meaning:
-dma Parallel port's DMA channel, or -1 if none is being
- used.
+ =============== =======================================
+ PCSPP PC-style SPP registers are available.
+ TRISTATE Port is bidirectional.
+ COMPAT Hardware acceleration for printers is
+ available and will be used.
+ EPP Hardware acceleration for EPP protocol
+ is available and will be used.
+ ECP Hardware acceleration for ECP protocol
+ is available and will be used.
+ DMA DMA is available and will be used.
+ =============== =======================================
-modes Parallel port's hardware modes, comma-separated,
- meaning:
+ Note that the current implementation will only take
+ advantage of COMPAT and ECP modes if it has an IRQ
+ line to use.
- PCSPP PC-style SPP registers are available.
- TRISTATE Port is bidirectional.
- COMPAT Hardware acceleration for printers is
- available and will be used.
- EPP Hardware acceleration for EPP protocol
- is available and will be used.
- ECP Hardware acceleration for ECP protocol
- is available and will be used.
- DMA DMA is available and will be used.
+``autoprobe`` Any IEEE-1284 device ID information that has been
+ acquired from the (non-IEEE 1284.3) device.
- Note that the current implementation will only take
- advantage of COMPAT and ECP modes if it has an IRQ
- line to use.
+``autoprobe[0-3]`` IEEE 1284 device ID information retrieved from
+ daisy-chain devices that conform to IEEE 1284.3.
-autoprobe Any IEEE-1284 device ID information that has been
- acquired from the (non-IEEE 1284.3) device.
+``spintime`` The number of microseconds to busy-loop while waiting
+ for the peripheral to respond. You might find that
+ adjusting this improves performance, depending on your
+ peripherals. This is a port-wide setting, i.e. it
+ applies to all devices on a particular port.
-autoprobe[0-3] IEEE 1284 device ID information retrieved from
- daisy-chain devices that conform to IEEE 1284.3.
+``timeslice`` The number of milliseconds that a device driver is
+ allowed to keep a port claimed for. This is advisory,
+ and driver can ignore it if it must.
-spintime The number of microseconds to busy-loop while waiting
- for the peripheral to respond. You might find that
- adjusting this improves performance, depending on your
- peripherals. This is a port-wide setting, i.e. it
- applies to all devices on a particular port.
-
-timeslice The number of milliseconds that a device driver is
- allowed to keep a port claimed for. This is advisory,
- and driver can ignore it if it must.
-
-default/* The defaults for spintime and timeslice. When a new
- port is registered, it picks up the default spintime.
- When a new device is registered, it picks up the
- default timeslice.
+``default/*`` The defaults for spintime and timeslice. When a new
+ port is registered, it picks up the default spintime.
+ When a new device is registered, it picks up the
+ default timeslice.
+======================= =======================================================
Device drivers
==============
@@ -193,31 +199,31 @@ Once the parport code is initialised, you can attach device drivers to
specific ports. Normally this happens automatically; if the lp driver
is loaded it will create one lp device for each port found. You can
override this, though, by using parameters either when you load the lp
-driver:
+driver::
# insmod lp parport=0,2
-or on the LILO command line:
+or on the LILO command line::
lp=parport0 lp=parport2
-Both the above examples would inform lp that you want /dev/lp0 to be
-the first parallel port, and /dev/lp1 to be the _third_ parallel port,
+Both the above examples would inform lp that you want ``/dev/lp0`` to be
+the first parallel port, and /dev/lp1 to be the **third** parallel port,
with no lp device associated with the second port (parport1). Note
that this is different to the way older kernels worked; there used to
be a static association between the I/O port address and the device
-name, so /dev/lp0 was always the port at 0x3bc. This is no longer the
-case - if you only have one port, it will default to being /dev/lp0,
+name, so ``/dev/lp0`` was always the port at 0x3bc. This is no longer the
+case - if you only have one port, it will default to being ``/dev/lp0``,
regardless of base address.
Also:
* If you selected the IEEE 1284 support at compile time, you can say
- `lp=auto' on the kernel command line, and lp will create devices
+ ``lp=auto`` on the kernel command line, and lp will create devices
only for those ports that seem to have printers attached.
- * If you give PLIP the `timid' parameter, either with `plip=timid' on
- the command line, or with `insmod plip timid=1' when using modules,
+ * If you give PLIP the ``timid`` parameter, either with ``plip=timid`` on
+ the command line, or with ``insmod plip timid=1`` when using modules,
it will avoid any ports that seem to be in use by other devices.
* IRQ autoprobing works only for a few port types at the moment.
@@ -229,39 +235,41 @@ If you are having problems printing, please go through these steps to
try to narrow down where the problem area is.
When reporting problems with parport, really you need to give all of
-the messages that parport_pc spits out when it initialises. There are
+the messages that ``parport_pc`` spits out when it initialises. There are
several code paths:
-o polling
-o interrupt-driven, protocol in software
-o interrupt-driven, protocol in hardware using PIO
-o interrupt-driven, protocol in hardware using DMA
+- polling
+- interrupt-driven, protocol in software
+- interrupt-driven, protocol in hardware using PIO
+- interrupt-driven, protocol in hardware using DMA
-The kernel messages that parport_pc logs give an indication of which
+The kernel messages that ``parport_pc`` logs give an indication of which
code path is being used. (They could be a lot better actually..)
For normal printer protocol, having IEEE 1284 modes enabled or not
should not make a difference.
To turn off the 'protocol in hardware' code paths, disable
-CONFIG_PARPORT_PC_FIFO. Note that when they are enabled they are not
-necessarily _used_; it depends on whether the hardware is available,
+``CONFIG_PARPORT_PC_FIFO``. Note that when they are enabled they are not
+necessarily **used**; it depends on whether the hardware is available,
enabled by the BIOS, and detected by the driver.
-So, to start with, disable CONFIG_PARPORT_PC_FIFO, and load parport_pc
-with 'irq=none'. See if printing works then. It really should,
+So, to start with, disable ``CONFIG_PARPORT_PC_FIFO``, and load ``parport_pc``
+with ``irq=none``. See if printing works then. It really should,
because this is the simplest code path.
-If that works fine, try with 'io=0x378 irq=7' (adjust for your
+If that works fine, try with ``io=0x378 irq=7`` (adjust for your
hardware), to make it use interrupt-driven in-software protocol.
-If _that_ works fine, then one of the hardware modes isn't working
-right. Enable CONFIG_PARPORT_PC_FIFO (no, it isn't a module option,
+If **that** works fine, then one of the hardware modes isn't working
+right. Enable ``CONFIG_FIFO`` (no, it isn't a module option,
and yes, it should be), set the port to ECP mode in the BIOS and note
-the DMA channel, and try with:
+the DMA channel, and try with::
io=0x378 irq=7 dma=none (for PIO)
io=0x378 irq=7 dma=3 (for DMA)
---
+
+----------
+
philb@xxxxxxx
tim@xxxxxxxxxxxx
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
