On Wed, Sep 14, 2016 at 10:42:04AM +0530, Kishon Vijay Abraham I wrote:
> The PCIe controller integrated in dra7xx SoCs is capable of operating
> in endpoint mode. Add support for dra7xx SoCs to operate in endpoint
> mode.
>
> Signed-off-by: Kishon Vijay Abraham I <kishon@xxxxxx>
> ---
> Documentation/devicetree/bindings/pci/ti-pci.txt | 30 ++-
> drivers/pci/controller/Kconfig | 21 +++
> drivers/pci/controller/pci-dra7xx.c | 211 +++++++++++++++++++---
> 3 files changed, 225 insertions(+), 37 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt
> index 60e2516..b0e76f6 100644
> --- a/Documentation/devicetree/bindings/pci/ti-pci.txt
> +++ b/Documentation/devicetree/bindings/pci/ti-pci.txt
> @@ -1,17 +1,22 @@
> TI PCI Controllers
>
> PCIe Designware Controller
> - - compatible: Should be "ti,dra7-pcie""
> - - reg : Two register ranges as listed in the reg-names property
> - - reg-names : The first entry must be "ti-conf" for the TI specific registers
> - The second entry must be "rc-dbics" for the designware pcie
> - registers
> - The third entry must be "config" for the PCIe configuration space
> + - compatible: Should be "ti,dra7-pcie" for RC
> + Should be "ti,dra7-pcie-ep" for EP
> - phys : list of PHY specifiers (used by generic PHY framework)
> - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
> number of PHYs as specified in *phys* property.
> - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>",
> where <X> is the instance number of the pcie from the HW spec.
> + - num-lanes as specified in ../designware-pcie.txt
> +
> +HOST MODE
> +=========
> + - reg : Two register ranges as listed in the reg-names property
> + - reg-names : The first entry must be "ti-conf" for the TI specific registers
> + The second entry must be "rc-dbics" for the designware pcie
> + registers
> + The third entry must be "config" for the PCIe configuration space
> - interrupts : Two interrupt entries must be specified. The first one is for
> main interrupt line and the second for MSI interrupt line.
> - #address-cells,
> @@ -19,13 +24,24 @@ PCIe Designware Controller
> #interrupt-cells,
> device_type,
> ranges,
> - num-lanes,
> interrupt-map-mask,
> interrupt-map : as specified in ../designware-pcie.txt
>
> Optional Property:
> - gpios : Should be added if a gpio line is required to drive PERST# line
Don't you need gpios as the input side of GPIO outputs in RC mode? Or
for EP mode they are all handled by h/w?
>
> +DEVICE MODE
> +===========
> + - reg : Two register ranges as listed in the reg-names property
> + - reg-names : "ti-conf" for the TI specific registers
> + "ep_dbics" for the standard configuration registers as
> + they are locally accessed within the DIF CS space
> + "ep_dbics2" for the standard configuration registers as
> + they are locally accessed within the DIF CS2 space
> + - interrupts : one interrupt entries must be specified for main interrupt.
> + - num-ib-windows : number of inbound address translation windows
> + - num-ob-windows : number of outbound address translation windows
> +
> Example:
> axi {
> compatible = "simple-bus";
> diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
> index 8574828..4d70981 100644
> --- a/drivers/pci/controller/Kconfig
> +++ b/drivers/pci/controller/Kconfig
> @@ -23,6 +23,27 @@ config PCI_DRA7XX_HOST
> Enables support for the PCIe controller in the DRA7xx SoC to work in
> host mode.
>
> +config PCI_DRA7XX_EP
> + bool "Endpoint Only Mode"
> + depends on PCI_ENDPOINT
> + select PCIE_DW_EP
> + help
> + Enables support for the PCIe controller in the DRA7xx SoC to work in
> + endpoint mode.
> +
> +config PCI_DRA7XX_HOST_EP
I'd make these 2 options just RC and EP depending on PCI_DRA7XX_HOST
with RC option being default yes.
> + bool "Both Host and Endpoint Mode"
> + depends on PCI_MSI_IRQ_DOMAIN
> + depends on PCI
> + depends on PCI_ENDPOINT
> + select PCIE_DW_HOST
> + select PCIE_DW_EP
> + help
> + Enables support for the PCIe controller in the DRA7xx SoC to work in
> + both endpoint mode and host mode. If the board has 2 PCIe ports and
> + one of them has to work in host mode and the other has to work in
> + EP mode then this option has to be enabled.
> +
> endchoice
>
> endif
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
