Hi!
I have a pair of boards with this i2c topology:
GPIO ---| ------ BAT1
| v /
I2C -----+------B---+---- MUX
| \
EEPROM ------ BAT2
(B denotes the boundary between the boards)
The problem with this is that the GPIO controller sits on the same i2c bus
that it MUXes. For pca954x devices this is worked around by using unlocked
transfers when updating the MUX. I have no such luck as the GPIO is a general
purpose IO expander and the MUX is just a random bidirectional MUX, unaware
of the fact that it is muxing an i2c bus. Extending unlocked transfers
into the GPIO subsystem is too ugly to even think about. But the general hw
approach is sane in my opinion, with the number of connections between the
two boards minimized. To put it plainly, I need support for it.
So, I observe that while it is needed to have the i2c bus locked during the
actual MUX update in order to avoid random garbage on the slave side, it
is not strictly a must to have it locked over the whole sequence of a full
select-transfer-deselect operation. The MUX itself needs to be locked, so
transfers to clients behind the mux are serialized, and the MUX needs to be
stable during all i2c traffic (otherwise individual mux slave segments
might see garbage).
This series accomplishes this by adding code to i2c-mux-gpio and
i2c-mux-pinctrl that determines if all involved devices used to update the
mux are controlled by the same root i2c adapter that is muxed. When this
is the case, the select-transfer-deselect operations should be locked
individually to avoid the deadlock. The i2c bus *is* still locked
during muxing, since the muxing happens as part of i2c transfers. This
is true even if the MUX is updated with several transfers to the GPIO (at
least as long as *all* MUX changes are using the i2c master bus). A lock
is added to i2c adapters that muxes on that adapter grab, so that transfers
through the muxes are serialized.
Concerns:
- The locking is perhaps too complex?
- I worry about the priority inheritance aspect of the adapter lock. When
the transfers behind the mux are divided into select-transfer-deselect all
locked individually, low priority transfers get more chances to interfere
with high priority transfers.
- When doing an i2c_transfer() in_atomic() context or with irqs_disabled(),
there is a higher possibility that the mux is not returned to its idle
state after a failed (-EAGAIN) transfer due to trylock.
- Is the detection of i2c-controlled gpios and pinctrls sane (i.e. the
usage of the new i2c_root_adapter() function in 18/24)?
To summarize the series, there's some i2c-mux infrastructure cleanup work
first (I think that part stands by itself as desireable regardless), the
locking changes are in 16/24 and after with the real meat in 18/24. There
is some documentation added in 19/24 while 20/24 and after are cleanups to
existing drivers utilizing the new stuff.
PS. needs a bunch of testing, I do not have access to all the involved hw.
Thanks to those who have ested this series so far. At this point, only
patches 01 through 15 are planned for 4.6, and the rest will hopefully
follow later, so lets focus of the cleanup work that enables the real
work later in the series.
Antti, you reviewed 09 through 12 for v5, and even though they changed
slightly due to the changes in v7 I have kept your reviewed tags, since
I classified the changes as mechanical. I hope this is ok.
Similarly, Jonathan and Rob acked patch 08 and 14 respectively, and these
patches have the same kind of mechanical changes so I have kept the acks.
I hope this is also ok.
I have also kept the acks and review tags on patches 20 and forward since
the fixups to adjust to the changes earlier in the series were completely
trivial.
This series can also be pulled from github, if that is preferred:
---------------------
The following changes since commit f55532a0c0b8bb6148f4e07853b876ef73bc69ca:
Linux 4.6-rc1 (2016-03-26 16:03:24 -0700)
are available in the git repository at:
https://github.com/peda-r/i2c-mux.git mux-core-and-locking-7
for you to fetch changes up to f725ef789ff0eb2663f1cff2b29d8196a7f0fd0b:
[media] rtl2832: regmap is aware of lockdep, drop local locking hack (2016-04-20 14:49:00 +0200)
---------------------
v7 compared to v6:
- Removed i2c_mux_reserve_adapters, and all realloc attempts in
i2c_mux_add_adapter. Supply a maximum number of adapters in i2c_mux_alloc
instead.
- Removed i2c_mux_one_adapter since it is was hard to use correctly, which
was evident from the crash in the mpu6050 driver (on a mpu9150 chip) reported
by Crestez Dan Leonard. Also, it didn't make things all that much simpler
anyway (even if used correctly).
- Rename i2c_mux_core:adapters into i2c_mux_core:num_adapters.
- Some grammar and spelling fixes.
v6 compared to v5:
- Rebase on top of v4.6-rc1
- Adjust to gpio subsystem overhaul.
- Adjust to changes in the inv_mpu6050 driver.
- Adjust to changes in the rtl2832 driver.
- Fix some new trivial checkpatch issues.
- Rename "self-locked" muxes "mux-locked" instead, since the lock has
been moved to the parent adapter and is common for all muxes with
the same parent adapter. The advantage is that address collisions
behind sibling muxes are handled. Parent-locked muxes also grab this
new mux-lock so that parent-locked and mux-locked siblings interact
better.
- Firmware mutex added to the si2168 driver.
v5 compared to v4 (only published as a git branch):
- Rebase on top of v4.5-rc7.
- A new patch making me maintainer of i2c muxes (also sent separately).
- A new file Documentation/i2c/i2c-topology that describes various muxing
issues.
- Rename "i2c-controlled" muxes "self-locked" instead, as it is perfectly
reasonable to have i2c-controlled muxes that use the pre-existing locking
scheme. The pre-existing locking scheme for i2c muxes is from here on
called "parent-locked".
- Rename i2c-mux.c:i2c_mux_master_xfer to __i2c_mux_master_xfer since it
calls __i2c_transfer, which leaves room for a new i2c_mux_master_xfer
that calls i2c_transfer. Similar rename shuffle for i2c_mux_smbus_xfer.
- Use sizeof(*priv) instead of sizeof(struct i2c_mux_priv). One instance.
- Some follow-up patches that were posted in response to v2-v4 cleaning up
and simplifying various i2c muxes outside drivers/i2c/, among those is
an unrelated cleanup patch to drivers/media/dvb-frontends/rtl2832.c that
I carry here since it conflicts (trivially) with this series. That
unrelated patch is (currently) the last patch in the series.
v4 compared to v3:
- Rebase on top of v4.5-rc6.
- Update to add new i2c-mux interfaces in 01/18 including glue to implement
the old interfaces in terms of the new interfaces, then change the
mux users over to the new interfaces one by one (in 02/18 through 14/18),
and finally removing the old interfaces in 15/18. I.e. the first 15
patches of v4 replaces the first 5 patches of v3, with the following
points describing changes in the end result. Each patch is now touching
only one subsystem.
- Rename i2c_add_mux_adapter and i2c_del_mux_adapters to i2c_mux_add_adapter
and i2c_mux_del_adapters (so that the old functions can live on during the
transition).
- Make i2c_mux_alloc take a parent and the select/deselect ops as
arguments. Also add a flags argument to prevent churn later on.
- Add a new interface i2c_mux_one_adapter(). Make use of it in suitable
mux users with a single child adapter.
- Adjust to a rename in struct gpio_chip.
- Update a couple of comments to match the new code.
v3 compared to v2:
- Fix devm_kfree of a NULL pointer in i2c_mux_reserve_adapters().
- Remove device tree "i2c-controlled" property and determine this by walking
the dev tree instead.
- Fix compile problems with inv_mpu_acpi.c
- Wait with adding the client pointer to patch 2/8 for pca9541 and pca954x.
v2 compared to v1:
- Allocate mux core and (optional) priv in a combined allocation.
- Kill dev_err messages triggered by memory allocation failure.
- Fix the device specific i2c muxes that I had overlooked.
- Rebase on top of v4.4-rc8 (was based on v4.4-rc6 previously).
- Drop the last two patches in the series.
Cheers,
Peter
Antti Palosaari (1):
[media] si2168: change the i2c gate to be mux-locked
Peter Rosin (23):
i2c-mux: add common data for every i2c-mux instance
i2c: i2c-mux-gpio: convert to use an explicit i2c mux core
i2c: i2c-mux-pinctrl: convert to use an explicit i2c mux core
i2c: i2c-arb-gpio-challenge: convert to use an explicit i2c mux core
i2c: i2c-mux-pca9541: convert to use an explicit i2c mux core
i2c: i2c-mux-pca954x: convert to use an explicit i2c mux core
i2c: i2c-mux-reg: convert to use an explicit i2c mux core
iio: imu: inv_mpu6050: convert to use an explicit i2c mux core
[media] m88ds3103: convert to use an explicit i2c mux core
[media] rtl2830: convert to use an explicit i2c mux core
[media] rtl2832: convert to use an explicit i2c mux core
[media] si2168: convert to use an explicit i2c mux core
[media] cx231xx: convert to use an explicit i2c mux core
of/unittest: convert to use an explicit i2c mux core
i2c-mux: drop old unused i2c-mux api
i2c: allow adapter drivers to override the adapter locking
i2c: muxes always lock the parent adapter
i2c-mux: relax locking of the top i2c adapter during mux-locked muxing
i2c-mux: document i2c muxes and elaborate on parent-/mux-locked muxes
iio: imu: inv_mpu6050: change the i2c gate to be mux-locked
[media] rtl2832: change the i2c gate to be mux-locked
[media] rtl2832_sdr: get rid of empty regmap wrappers
[media] rtl2832: regmap is aware of lockdep, drop local locking hack
Documentation/i2c/i2c-topology | 370 +++++++++++++++++++++++++++
MAINTAINERS | 1 +
drivers/i2c/i2c-core.c | 66 +++--
drivers/i2c/i2c-mux.c | 297 ++++++++++++++++-----
drivers/i2c/muxes/i2c-arb-gpio-challenge.c | 47 ++--
drivers/i2c/muxes/i2c-mux-gpio.c | 73 +++---
drivers/i2c/muxes/i2c-mux-pca9541.c | 58 ++---
drivers/i2c/muxes/i2c-mux-pca954x.c | 61 +++--
drivers/i2c/muxes/i2c-mux-pinctrl.c | 121 +++++----
drivers/i2c/muxes/i2c-mux-reg.c | 69 ++---
drivers/iio/imu/inv_mpu6050/inv_mpu_acpi.c | 2 +-
drivers/iio/imu/inv_mpu6050/inv_mpu_core.c | 1 -
drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c | 81 ++----
drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h | 3 +-
drivers/media/dvb-frontends/m88ds3103.c | 19 +-
drivers/media/dvb-frontends/m88ds3103_priv.h | 2 +-
drivers/media/dvb-frontends/rtl2830.c | 20 +-
drivers/media/dvb-frontends/rtl2830_priv.h | 2 +-
drivers/media/dvb-frontends/rtl2832.c | 243 +++---------------
drivers/media/dvb-frontends/rtl2832.h | 4 +-
drivers/media/dvb-frontends/rtl2832_priv.h | 3 +-
drivers/media/dvb-frontends/rtl2832_sdr.c | 303 ++++++++++------------
drivers/media/dvb-frontends/rtl2832_sdr.h | 5 +-
drivers/media/dvb-frontends/si2168.c | 106 +++-----
drivers/media/dvb-frontends/si2168_priv.h | 3 +-
drivers/media/usb/cx231xx/cx231xx-core.c | 6 +-
drivers/media/usb/cx231xx/cx231xx-i2c.c | 47 ++--
drivers/media/usb/cx231xx/cx231xx.h | 4 +-
drivers/media/usb/dvb-usb-v2/rtl28xxu.c | 5 +-
drivers/of/unittest.c | 37 +--
include/linux/i2c-mux.h | 53 +++-
include/linux/i2c.h | 29 ++-
32 files changed, 1225 insertions(+), 916 deletions(-)
create mode 100644 Documentation/i2c/i2c-topology
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
