Hi Uwe,
Uwe Kleine-König <uwe@xxxxxxxxxxxxxxxxx> writes:
> On 12/16/2014 12:54 AM, Arnaud Ebalard wrote:
>>
>> This patch adds alarm support to Intersil ISL12057 driver. The chip
>> supports two separate alarms:
>>
>> - Alarm1: works up to one month in the future and accurate to the
>> second, associated w/ IRQ#2 pin
>> - Alarm2: works up to one month in the future and accurate to the
>> minute, associated w/ IRQ#1 or IRQ#2 pin (configuable).
>>
>> This patch only adds support for Alarm1 which allows to configure
>> the chip to generate an interrupt on IRQ#2 pin when current time
>> matches the alarm.
>>
>> This patch was tested on a Netgear ReadyNAS 102 after some soldering
>> of the IRQ#2 pin of the RTC chip to a MPP line of the SoC (the one
>> used usually handles the reset button). The test was performed using
>> a modified .dts file reflecting this change (see below) and rtc-test.c
>> program available in Documentation/rtc.txt. This test program ran as
>> expected, which validates alarm supports, including interrupt support.
>>
>> As a side note, the ISL12057 remains in the list of trivial devices,
>> i.e. no specific DT binding being added by this patch: i2c core
>> automatically handles extraction of IRQ line info from .dts file. For
>> instance, if one wants to reference the interrupt line for the
>> alarm in its .dts file, adding interrupt and interrupt-parent
>> properties works as expected (if the primary function of your
>> interrupt pin is not GPIO, you will need some additional pinctrl
>> properties):
>>
>> isl12057: isl12057@68 {
>> compatible = "isil,isl12057";
>> interrupt-parent = <&gpio0>;
>> interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
>> reg = <0x68>;
>> };
>>
>> FWIW, if someone is looking for a way to test alarm support this can
>> be done in the following way:
>>
>> # echo `date '+%s' -d '+ 1 minutes'` > /sys/class/rtc/rtc0/wakealarm
>> # shutdown -h now
>>
>> With the commands above, after a minute, the system comes back to life.
> This paragraph belongs into the 2nd patch, right?
no, it is for this patch. I did a specific commit message for the second
patch. IIRC, it also has the example if it was the meaning of your
question.
>> diff --git a/drivers/rtc/rtc-isl12057.c b/drivers/rtc/rtc-isl12057.c
>> index 6e1fcfb5d7e6..3ec73ad7f2d8 100644
>> --- a/drivers/rtc/rtc-isl12057.c
>> +++ b/drivers/rtc/rtc-isl12057.c
>> @@ -79,8 +79,10 @@
>> #define ISL12057_MEM_MAP_LEN 0x10
>>
>> struct isl12057_rtc_data {
>> + struct rtc_device *rtc;
>> struct regmap *regmap;
>> struct mutex lock;
>> + int irq;
> interrupts are usually unsigned values. Hmm, I see that it simplifies a
> bit here, as the function to determine the irq returns the actual value
> or a negative error. As there would be problems anyhow for irq values >
> INT_MAX probably this comment isn't that important.
ok.
>> +/*
>> + * Note: as we only read from device and do not perform any update, there is
>> + * no need for an equivalent function which would try and get driver's main
>> + * lock. Here, it is safe for everyone if we just use regmap internal lock
>> + * on the device when reading.
>> + */
>> +static int _isl12057_rtc_read_time(struct device *dev, struct rtc_time *tm)
>> {
>> struct isl12057_rtc_data *data = dev_get_drvdata(dev);
>> u8 regs[ISL12057_RTC_SEC_LEN];
>> unsigned int sr;
>> int ret;
>>
>> - mutex_lock(&data->lock);
>> ret = regmap_read(data->regmap, ISL12057_REG_SR, &sr);
>> if (ret) {
>> dev_err(dev, "%s: unable to read oscillator status flag (%d)\n",
>> @@ -187,8 +222,6 @@ static int isl12057_rtc_read_time(struct device *dev, struct rtc_time *tm)
>> __func__, ret);
>>
>> out:
>> - mutex_unlock(&data->lock);
>> -
>> if (ret)
>> return ret;
>>
>
> Is this locking update worth a separate change?
I do not think it needs a separate change (to simplify bisect for
instance) because the mutex protection can safely be removed here
around the two tests because the first read (to check oscillator bit)
and second read (to get time if oscillator bit is ok) we are doing on
the device do not need to be globally protected: oscillator bit is not
something we will update in such a way it would out of sync with the
current state of the time value kept by the device. More precisely, in
isl12057_rtc_set_time(), we do update the oscillator but only *after*
the time has been set to a valid value.
Cheers,
a+
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
