Caesar,
On Fri, Oct 24, 2014 at 11:21:46AM +0800, Caesar Wang wrote:
> Dmitry,
>
> 在 2014/10/24 10:32, Dmitry Torokhov 写道:
> >On Fri, Oct 24, 2014 at 10:06:43AM +0800, Caesar Wang wrote:
> >>在 2014/10/24 9:37, Dmitry Torokhov 写道:
> >>>On October 23, 2014 6:08:52 PM PDT, Caesar Wang <caesar.wang@xxxxxxxxxxxxxx> wrote:
> >>>>Dmitry,
> >>>>
> >>>>在 2014/10/24 8:46, Dmitry Torokhov 写道:
> >>>>>Hi Caesar,
> >>>>>
> >>>>>On Thu, Oct 23, 2014 at 05:40:06PM +0800, Caesar Wang wrote:
> >>>>>>This patch is depend on rk3288-thermal.dtsi,or
> >>>>>>it will compile error.
> >>>>>>
> >>>>>>If the temperature over a period of time High,over 120C
> >>>>>>the resulting TSHUT gave CRU module,let it reset
> >>>>>>the entire chip,or via GPIO give PMIC.
> >>>>>>
> >>>>>>Signed-off-by: Caesar Wang <caesar.wang@xxxxxxxxxxxxxx>
> >>>>>>---
> >>>>>> arch/arm/boot/dts/rk3288.dtsi | 21 +++++++++++++++++++++
> >>>>>> 1 file changed, 21 insertions(+)
> >>>>>>
> >>>>>>diff --git a/arch/arm/boot/dts/rk3288.dtsi
> >>>>b/arch/arm/boot/dts/rk3288.dtsi
> >>>>>>index cb18bb4..85fc17a 100644
> >>>>>>--- a/arch/arm/boot/dts/rk3288.dtsi
> >>>>>>+++ b/arch/arm/boot/dts/rk3288.dtsi
> >>>>>>@@ -15,6 +15,7 @@
> >>>>>> #include <dt-bindings/interrupt-controller/arm-gic.h>
> >>>>>> #include <dt-bindings/pinctrl/rockchip.h>
> >>>>>> #include <dt-bindings/clock/rk3288-cru.h>
> >>>>>>+#include <dt-bindings/thermal/thermal.h>
> >>>>>> #include "skeleton.dtsi"
> >>>>>> / {
> >>>>>>@@ -66,6 +67,7 @@
> >>>>>> 216000 900000
> >>>>>> 126000 900000
> >>>>>> >;
> >>>>>>+ #cooling-cells = <2>; /* min followed by max */
> >>>>>> clock-latency = <40000>;
> >>>>>> clocks = <&cru ARMCLK>;
> >>>>>> };
> >>>>>>@@ -346,6 +348,19 @@
> >>>>>> status = "disabled";
> >>>>>> };
> >>>>>>+ tsadc: tsadc@ff280000 {
> >>>>>>+ compatible = "rockchip,rk3288-tsadc";
> >>>>>>+ reg = <0xff280000 0x100>;
> >>>>>>+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> >>>>>>+ clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>;
> >>>>>>+ clock-names = "tsadc", "apb_pclk";
> >>>>>>+ pinctrl-names = "default";
> >>>>>>+ pinctrl-0 = <&otp_out>;
> >>>>>>+ #thermal-sensor-cells = <1>;
> >>>>>>+ hw-shut-temp = <120000>;
> >>>>>I do not think this is a good value. You have (in the other DTS file)
> >>>>>passive trip point at 80 and critical (which should result in orderly
> >>>>>shutdown) at 125. But here you define hardware-controlled shutdown at
> >>>>>120C, which is backwards. You should have:
> >>>>>
> >>>>>passive <= critical <= hardware
> >>>>Hmmm....
> >>>>but, the system will shutdown when temperature over critial value,
> >>>>there is no chance of triggering the TSHUT.
> >>>>
> >>>>If the temperature over a period of time High,as we know,
> >>>>the resulting TSHUT gave CRU module,let it hot-reset the entire chip,
> >>>>or via GPIO give PMIC cold-reset the entire chip.
> >>>Having tshut trigger is not the goal, tshut is the measure of last resort. If we can handle thermal conditions without triggering tshut, we achieved our goal.
> >>>
> >>>Tshut triggering is " oh, crap, nothing we tried works" scenario.
> >>I don't think so.
> >>
> >>In general,We should have:
> >>passive <= hardware(reset entire chip) <= critical(shutdown)
> >>
> >>The temperature be rising qulckly if have some other conditions,
> >>the "critical" will play a role.
> >No, I think it should be the other way around: if we are unable to cool
> >down the laptop under load we need to shut it down and let it cool. If
> >for some reason we are unable to shut it down in orderly fashion (kernel
> >is stuck holding a lock or similar) then hardware will reset it.
> >
> >At least that's how I understand it.
> hmmm....
>
> OK,agree,this is a option.
>
> I think I should set hw-shut-temp = <125000>;
> and critical = <120000>;
>
Yes, this should work, thanks!
--
Dmitry
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
