Re: [PATCH v3 1/4] thermal: rockchip: add driver for thermal

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Am Donnerstag, 28. August 2014, 10:37:35 schrieb Eduardo Valentin:
> Ceasar and Arnd,
> 
> On Thu, Aug 28, 2014 at 10:48:23AM +0200, Arnd Bergmann wrote:
> > On Thursday 28 August 2014 08:59:19 Caesar Wang wrote:
> > > Thermal is TS-ADC Controller module supports user-defined mode and
> > > automatic mode.
> > > 
> > > User-defined mode refers,TSADC all the control signals entirely by
> > > software
> > > writing to register for direct control.
> > > 
> > > Automaic mode refers to the module automatically poll TSADC output,and
> > > the results Were checked.
> > > 
> > > If you find that the temperature High in a period of time, an interrupt
> > > is generated to the processor down-measures taken;if the temperature
> > > over a period of time High, the resulting TSHUT gave CRU module,let it
> > > reset the entire chip, or via GPIO give PMIC.
> > > 
> > > Signed-off-by: zhaoyifeng <zyf@xxxxxxxxxxxxxx>
> > > Signed-off-by: Caesar Wang <caesar.wang@xxxxxxxxxxxxxx>
> > 
> > Hi Caesar,
> > 
> > After looking at the driver (last time I only received the patch for
> > the binding), I have a more general comment:
> > 
> > This looks like a general-purpose ADC device, not an IP block that is
> > specific to thermal management. The binding looks ok for that purpose
> > but should probably be moved into
> > Documentation/devicetree/bindings/iio/adc/ as a minor change.
> 
> I agree with Arnd's point here. It makes sense to me to have this driver
> under the IIO umbrella.

interesting suggestion :-)

I've just taken another look at the registers of the ts-adc on the rk3066 
which is completely different from the rk3288 one. Interestingly the rk3066 one 
is "just" another saradc IP, so for this one it would really make sense.


> > On the driver side, I believe the correct way to deal with this setup
> > is to split your driver into a generic drivers/iio/adc/rockchips-tsadc.c
> > file, and a smaller thermal driver that uses the iio in-kernel interfaces,
> > ideally one that is independent of the underlying hardware and can
> > work on any ADC implementation.
> 
> Agreed. If you can write such interface and make your driver to work in
> such way, that would be great.

But I currently don't see how you would model the temperature handling parts 
from a generic thermal driver to a generic adc driver for the rk3288-tsadc.

I guess the general temperature irq handling would use iio-triggers? But how 
does the target temperature get into the TSADC_COMP1_INT register.

Also when getting the temperature, Caesar's driver compares it to its trip 
points and sets the next trip point depending on the current temperature 
(passive <-> critical) in rockchip_get_temp.

Maybe there is some completely easy way for this, but currently I don't see 
it.


Heiko
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux