Arnd Bergmann schrieb:
> The ADC in s3c64xx is almost the same as exynosv1, but
> has a different 'select' method. Adding this here will be
> helpful to move over the existing s3c64xx platform from the
> legacy plat-samsung/adc driver to the new exynos-adc.
>
> Signed-off-by: Arnd Bergmann <arnd@xxxxxxxx>
> ---
There are some style issues, see the comments inline.
> [In reply to Exynos3250 ADC support, adding Heiko and Ben]
>
> I spent way too much time this week trying to clean up the
> old plat-samsung/adc.c driver as preparation for s3c64xx multiplatform
> support. Eventually I figured out that all that code is much simpler
> done using the new driver. This adds support for s3c64xx in
> samsung-adc.c, similar code changes can be done to support the
> various s3c24xx variants as well.
>
> This first patch should be fairly straightforward but is not tested
> yet. The second patch is more tricky.
>
> Both are based on the exynos3250 patches sent by Chanwoo Choi.
>
> diff --git a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt
> index 26232f98d8c5..f84e9250429b 100644
> --- a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt
> +++ b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt
> @@ -11,11 +11,21 @@ New driver handles the following
>
> Required properties:
> - compatible: Must be "samsung,exynos-adc-v1"
> - for exynos4412/5250 controllers.
> + for exynos4412/5250 and s5pv210 controllers.
> Must be "samsung,exynos-adc-v2" for
> future controllers.
> Must be "samsung,exynos3250-adc-v2" for
> controllers compatible with ADC of Exynos3250.
> + Must be "samsung,s3c2410-adc" for
> + the ADC in s3c2410 and compatibles
> + Must be "samsung,s3c2416-adc" for
> + the ADC in s3c2416 and compatibles
> + Must be "samsung,s3c2440-adc" for
> + the ADC in s3c2440 and compatibles
> + Must be "samsung,s3c2440-adc" for
> + the ADC in s3c2440 and compatibles
> + Must be "samsung,s3c2443-adc" for
> + the ADC in s3c2443 and compatibles
> - reg: Contains ADC register address range (base address and
> length) and the address of the phy enable register.
> - interrupts: Contains the interrupt information for the timer. The
> diff --git a/drivers/iio/adc/exynos_adc.c b/drivers/iio/adc/exynos_adc.c
> index b63e88247eb2..5f95638513d2 100644
> --- a/drivers/iio/adc/exynos_adc.c
> +++ b/drivers/iio/adc/exynos_adc.c
> @@ -39,12 +39,16 @@
> #include <linux/iio/machine.h>
> #include <linux/iio/driver.h>
>
> -/* EXYNOS4412/5250 ADC_V1 registers definitions */
> +/* S3C/EXYNOS4412/5250 ADC_V1 registers definitions */
> #define ADC_V1_CON(x) ((x) + 0x00)
> +#define ADC_V1_TSC(x) ((x) + 0x04)
> #define ADC_V1_DLY(x) ((x) + 0x08)
> #define ADC_V1_DATX(x) ((x) + 0x0C)
> +#define ADC_V1_DATY(x) ((x) + 0x10)
> +#define ADC_V1_UPDN(x) ((x) + 0x14)
> #define ADC_V1_INTCLR(x) ((x) + 0x18)
> #define ADC_V1_MUX(x) ((x) + 0x1c)
> +#define ADC_V1_CLRINTPNDNUP(x) ((x) + 0x20)
>
> /* Future ADC_V2 registers definitions */
> #define ADC_V2_CON1(x) ((x) + 0x00)
> @@ -60,6 +64,30 @@
> #define ADC_V1_CON_PRSCLV(x) (((x) & 0xFF) << 6)
> #define ADC_V1_CON_STANDBY (1u << 2)
>
Leave a whitespace around operators below.
> +#define ADC_S3C2410_CON_SELMUX(x) (((x)&0x7)<<3)
> +
> +/* ADCTSC Register Bits */
> +#define ADC_S3C2443_TSC_UD_SEN (1<<8)
> +#define ADC_S3C2410_TSC_YM_SEN (1<<7)
> +#define ADC_S3C2410_TSC_YP_SEN (1<<6)
> +#define ADC_S3C2410_TSC_XM_SEN (1<<5)
> +#define ADC_S3C2410_TSC_XP_SEN (1<<4)
> +#define ADC_S3C2410_TSC_PULL_UP_DISABLE (1<<3)
> +#define ADC_S3C2410_TSC_AUTO_PST (1<<2)
> +#define ADC_S3C2410_TSC_XY_PST(x) (((x)&0x3)<<0)
> +
> +#define ADC_TSC_WAIT4INT (ADC_S3C2410_TSC_YM_SEN | \
> + ADC_S3C2410_TSC_YP_SEN | \
> + ADC_S3C2410_TSC_XP_SEN | \
> + ADC_S3C2410_TSC_XY_PST(3))
> +
> +#define ADC_TSC_AUTOPST (ADC_S3C2410_TSC_YM_SEN | \
> + ADC_S3C2410_TSC_YP_SEN | \
> + ADC_S3C2410_TSC_XP_SEN | \
> + ADC_S3C2410_TSC_AUTO_PST | \
> + ADC_S3C2410_TSC_XY_PST(0))
> +
> +
> /* Bit definitions for ADC_V2 */
> #define ADC_V2_CON1_SOFT_RESET (1u << 2)
>
> @@ -195,6 +223,26 @@ static void exynos_adc_v1_clear_irq(struct exynos_adc *info)
> writel(1, ADC_V1_INTCLR(info->regs));
> }
>
> +static void exynos_adc_s3c64xx_start_conv(struct exynos_adc *info,
> + unsigned long addr)
This indention could be a bit better.
> +{
> + u32 con1;
> +
> + con1 = readl(ADC_V1_CON(info->regs));
> + con1 &= ~ADC_S3C2410_CON_SELMUX(7);
> + con1 |= ADC_S3C2410_CON_SELMUX(addr);
> + writel(con1 | ADC_CON_EN_START, ADC_V1_CON(info->regs));
> +}
> +
> +static struct exynos_adc_data const exynos_adc_s3c64xx_data = {
> + .num_channels = MAX_ADC_V1_CHANNELS,
> +
> + .init_hw = exynos_adc_v1_init_hw,
> + .exit_hw = exynos_adc_v1_exit_hw,
> + .clear_irq = exynos_adc_v1_clear_irq,
> + .start_conv = exynos_adc_s3c64xx_start_conv,
> +};
> +
> static void exynos_adc_v1_start_conv(struct exynos_adc *info,
> unsigned long addr)
> {
> @@ -280,6 +328,9 @@ static struct exynos_adc_data const exynos3250_adc_v2_data = {
>
> static const struct of_device_id exynos_adc_match[] = {
> {
> + .compatible = "samsung,s3c64100-adc",
> + .data = &exynos_adc_s3c64xx_data,
> + }, {
> .compatible = "samsung,exynos-adc-v1",
> .data = (void *)&exynos_adc_v1_data,
> }, {
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-iio" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
