On 2014年06月30日 17:00, Arnd Bergmann wrote:
Overall a very nice driver. I didn't find any real bugs, but a few things
that could be changed for readability and micro-optimizations:
On Monday 30 June 2014 16:03:28 Zhou Wang wrote:
+#define hinfc_read(_host, _reg) readl(_host->iobase + (_reg))
+#define hinfc_write(_host, _value, _reg)\
+ writel((_value), _host->iobase + (_reg))
I'd recommend making these inline functions rather than macros.
I will change above macros to inline functions, thanks.
+struct hinfc_host {
+ struct nand_chip *chip;
+ struct mtd_info *mtd;
I notice that you allocate the nand_chip and mtd_info together
with the hinfc_host and then assign these pointers. A preferred
method is normally to just embed the structures in this case:
struct hinfc_host {
struct nand_chip chip;
struct mtd_info mtd;
so you avoid the pointer overhead, and can go back from these
two structures to the hinfc_host using container_of().
It is better to embed chip and mtd in host, I will change this, thanks.
+ struct device *dev;
+ void __iomem *iobase;
+ struct completion cmd_complete;
+ unsigned int offset;
+ unsigned int command;
+ int chipselect;
+ unsigned int addr_cycle;
+ unsigned int addr_value[2];
+ unsigned int cache_addr_value[2];
+ char *buffer;
+ dma_addr_t dma_buffer;
+ dma_addr_t dma_oob;
+ int version;
+ unsigned int ecc_bits;
+ unsigned int irq_status; /* interrupt status */
+
+ int (*send_cmd_pageprog)(struct hinfc_host *host);
+ int (*send_cmd_status)(struct hinfc_host *host);
+ int (*send_cmd_readstart)(struct hinfc_host *host);
+ int (*send_cmd_erase)(struct hinfc_host *host);
+ int (*send_cmd_readid)(struct hinfc_host *host);
+ int (*send_cmd_reset)(struct hinfc_host *host, int chipselect);
+};
Why do you need function pointers here? The current version of the
driver you posted always assigns these to the same functions, so
it would be more efficient to just call those directly.
If you plan to add another variant later that uses a different set
of functions here, you can add the function pointers then, in a
separate patch. Also, a common style element is to have a separate
constant structure with the function pointers:
const struct hinfc_host_ops ops = {
.send_cmd_pageprog = hisi_nfc_send_cmd_pageprog,
...
};
if you actually end up needing function pointers. That simplifies
the code a bit and is slightly more robust to attacks overwriting
the function pointers.
I will move above function pointers out of host and directly call the
functions, thanks for your good comment.
+
+void wait_controller_finished(struct hinfc_host *host)
+{
+ unsigned long timeout = jiffies + HINFC504_NFC_TIMEOUT;
+ int val;
+
+ while (time_before(jiffies, timeout)) {
+ val = hinfc_read(host, HINFC504_STATUS);
+ if (host->command == NAND_CMD_ERASE2) {
+ /* nfc is ready */
+ while (!(val & HINFC504_READY)) {
+ usleep_range(500, 1000);
+ val = hinfc_read(host, HINFC504_STATUS);
+ }
+ return;
+ } else {
+ if (val & HINFC504_READY)
+ return;
+ }
+ }
+
+ /* wait cmd timeout */
+ dev_err(host->dev, "Wait NAND controller exec cmd timeout.\n");
+}
Since the timeout is much bigger than the wait time here, I guess you
can use a wider range for the usleep_range(), e.g.
usleep_range(500, 50000);
which is nicer to other tasks. You will normally be woken up much earlier.
Arnd
As I know that the operating time of NAND flash erasure is about
ms-level, so I set sleep time as usleep_range(500, 1000) here. And the
timeout means that relative operations don't finish in this time, so
maybe there is something wrong with the operations. In normal situation,
after detecting the operation finished, the above function will return
before timeout arriving.
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
