Hi Gabi,
Sorry for the delay. It was a hectic week last week.
As promised:
> This patch adds ST Keyscan driver to use the keypad hw a subset
> of ST boards provide. Specific board setup will be put in the
> given dt.
>
> Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@xxxxxx>
> Signed-off-by: Gabriel Fernandez <gabriel.fernandez@xxxxxx>
Are you sure these are in the correct order?
What is the history of this commit?
> ---
> .../devicetree/bindings/input/st-keypad.txt | 50 ++++
This should be submitted as a seperate patch.
> drivers/input/keyboard/Kconfig | 12 +
> drivers/input/keyboard/Makefile | 1 +
> drivers/input/keyboard/st-keyscan.c | 323 +++++++++++++++++++++
> 4 files changed, 386 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/input/st-keypad.txt
> create mode 100644 drivers/input/keyboard/st-keyscan.c
>
> diff --git a/Documentation/devicetree/bindings/input/st-keypad.txt b/Documentation/devicetree/bindings/input/st-keypad.txt
> new file mode 100644
> index 0000000..63eb07a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/input/st-keypad.txt
> @@ -0,0 +1,50 @@
> +* ST Keypad controller device tree bindings
s/device tree/Device Tree
> +
> +The ST keypad controller device tree binding is based on the
As above.
> +matrix-keymap.
> +
> +Required properties:
> +
> +- compatible: "st,keypad"
I think there will be subsequent st,keypad drivers? Is there any way
we can make this compatible string more specific to _this_ device?
st,stih4xx-keypad?
> +- reg: Register base address of st-keypad controler.
s/address/address and size AND s/controler/controller
> +- interrupts: Interrupt numberof st-keypad controler.
s/numberof/number for the
> +- clocks: Must contain one entry, for the module clock.
> + See ../clocks/clock-bindings.txt for details.
Great!
> +- pinctrl-0: Should specify pin control groups used for this controller.
> +
> +- pinctrl-names: Should contain only one value - "default".
Like to ../pinctrl/pinctrl-bindings.txt
> +- linux,keymap: The keymap for keys as described in the binding document
> + devicetree/bindings/input/matrix-keymap.txt.
> +
> +- keypad,num-rows: Number of row lines connected to the keypad controller.
> +
> +- keypad,num-columns: Number of column lines connected to the keypad
> + controller.
> +
> +- st,debounce_us: Debouncing interval time in microseconds
I'm sure there will be a shared binding for de-bounce.
If not, there certainly should be.
> +
> +
Superfluous new lines.
> +Example:
> +
> +keyscan: keyscan@fe4b0000 {
> + compatible = "st,keypad";
Is there any way we can make this more specific to _this_ IP?
> + reg = <0xfe4b0000 0x2000>;
> + interrupts = <GIC_SPI 212 IRQ_TYPE_NONE>;
> + clocks = <&CLK_SYSIN>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_keyscan>;
> +
> + keypad,num-rows = <4>;
> + keypad,num-columns = <4>;
> + st,debounce_us = <5000>;
> + linux,keymap = < /* in0 in1 in2 in3 */
Do these line up in the file? I know Git can be a bit funny about this
sometimes.
> + KEY_F13 KEY_F9 KEY_F5 KEY_F1 /* out0 */
> + KEY_F14 KEY_F10 KEY_F6 KEY_F2 /* out1 */
> + KEY_F15 KEY_F11 KEY_F7 KEY_F3 /* out2 */
> + KEY_F16 KEY_F12 KEY_F8 KEY_F4 >; /* out3 */
> +};
> diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
> index a673c9f..9e29125 100644
> --- a/drivers/input/keyboard/Kconfig
> +++ b/drivers/input/keyboard/Kconfig
> @@ -512,6 +512,18 @@ config KEYBOARD_STOWAWAY
> To compile this driver as a module, choose M here: the
> module will be called stowaway.
>
> +config KEYBOARD_ST_KEYSCAN
> + tristate "STMicroelectronics keyscan support"
> + depends on ARCH_STI
> + select INPUT_EVDEV
> + select INPUT_MATRIXKMAP
> + help
> + Say Y here if you want to use a keypad attached to the keyscan block
> + on some STMicroelectronics SoC devices.
Might be worth mentioning which ones.
> + To compile this driver as a module, choose M here: the
> + module will be called stm-keyscan.
> +
> config KEYBOARD_SUNKBD
> tristate "Sun Type 4 and Type 5 keyboard"
> select SERIO
> diff --git a/drivers/input/keyboard/Makefile b/drivers/input/keyboard/Makefile
> index a699b61..5fd020a 100644
> --- a/drivers/input/keyboard/Makefile
> +++ b/drivers/input/keyboard/Makefile
> @@ -50,6 +50,7 @@ obj-$(CONFIG_KEYBOARD_SH_KEYSC) += sh_keysc.o
> obj-$(CONFIG_KEYBOARD_SPEAR) += spear-keyboard.o
> obj-$(CONFIG_KEYBOARD_STMPE) += stmpe-keypad.o
> obj-$(CONFIG_KEYBOARD_STOWAWAY) += stowaway.o
> +obj-$(CONFIG_KEYBOARD_ST_KEYSCAN) += st-keyscan.o
> obj-$(CONFIG_KEYBOARD_SUNKBD) += sunkbd.o
> obj-$(CONFIG_KEYBOARD_TC3589X) += tc3589x-keypad.o
> obj-$(CONFIG_KEYBOARD_TEGRA) += tegra-kbc.o
> diff --git a/drivers/input/keyboard/st-keyscan.c b/drivers/input/keyboard/st-keyscan.c
> new file mode 100644
> index 0000000..606cc19
> --- /dev/null
> +++ b/drivers/input/keyboard/st-keyscan.c
> @@ -0,0 +1,323 @@
> +/*
> + * STMicroelectronics Key Scanning driver
> + *
> + * Copyright (c) 2014 STMicroelectonics Ltd.
> + * Author: Stuart Menefy <stuart.menefy@xxxxxx>
> + *
> + * Based on sh_keysc.c, copyright 2008 Magnus Damm
Did sh_keysc.c ever exist in Mainline?
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/interrupt.h>
> +#include <linux/platform_device.h>
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +#include <linux/input/matrix_keypad.h>
> +
> +#define ST_KEYSCAN_MAXKEYS 16
> +
> +#define KEYSCAN_CONFIG_OFF 0x000
> +#define KEYSCAN_CONFIG_ENABLE 1
0x001?
> +#define KEYSCAN_DEBOUNCE_TIME_OFF 0x004
> +#define KEYSCAN_MATRIX_STATE_OFF 0x008
> +#define KEYSCAN_MATRIX_DIM_OFF 0x00c
Odd that these are 3 digit padded? Is there a reason for that?
> +#define KEYSCAN_MATRIX_DIM_X_SHIFT 0
> +#define KEYSCAN_MATRIX_DIM_Y_SHIFT 2
For all 'ST_KEYSCAN_...'?
> +struct keypad_platform_data {
> + const struct matrix_keymap_data *keymap_data;
> + unsigned int num_out_pads;
> + unsigned int num_in_pads;
> + unsigned int debounce_us;
> +};
> +
> +struct keyscan_priv {
> + void __iomem *base;
> + int irq;
> + struct clk *clk;
> + struct input_dev *input_dev;
> + struct keypad_platform_data *config;
> + unsigned int last_state;
> + u32 keycodes[ST_KEYSCAN_MAXKEYS];
Seems odd to limit this. Can't the information come from DT
i.e. keypad,num-rows and keypad,num-columns?
> +};
> +
> +static irqreturn_t keyscan_isr(int irq, void *dev_id)
> +{
> + struct platform_device *pdev = dev_id;
> + struct keyscan_priv *priv = platform_get_drvdata(pdev);
> + int state;
> + int change;
> +
> + state = readl(priv->base + KEYSCAN_MATRIX_STATE_OFF) & 0xffff;
> + change = priv->last_state ^ state;
> +
> + while (change) {
> + int scancode = __ffs(change);
> + int down = state & (1 << scancode);
int down = state & BIT(scancode);
> + input_report_key(priv->input_dev, priv->keycodes[scancode],
> + down);
> + change ^= 1 << scancode;
change ^= BIT(scancode);
> + };
> +
> + input_sync(priv->input_dev);
> +
> + priv->last_state = state;
> +
> + return IRQ_HANDLED;
> +}
> +
> +static void keyscan_start(struct keyscan_priv *priv)
> +{
> + clk_enable(priv->clk);
> +
> + writel(priv->config->debounce_us * (clk_get_rate(priv->clk) / 1000000),
> + priv->base + KEYSCAN_DEBOUNCE_TIME_OFF);
> +
> + writel(((priv->config->num_in_pads - 1) << KEYSCAN_MATRIX_DIM_X_SHIFT) |
> + ((priv->config->num_out_pads - 1) << KEYSCAN_MATRIX_DIM_Y_SHIFT),
> + priv->base + KEYSCAN_MATRIX_DIM_OFF);
> +
> + writel(KEYSCAN_CONFIG_ENABLE, priv->base + KEYSCAN_CONFIG_OFF);
> +}
> +
> +static void keyscan_stop(struct keyscan_priv *priv)
> +{
> + writel(0, priv->base + KEYSCAN_CONFIG_OFF);
> +
> + clk_disable(priv->clk);
> +}
> +
> +static int keypad_matrix_key_parse_dt(struct keyscan_priv *st_kp)
> +{
> + struct device *dev = st_kp->input_dev->dev.parent;
> + struct device_node *np = dev->of_node;
> + struct keypad_platform_data *pdata;
> + int error;
> +
> + pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
> + if (!pdata) {
> + dev_err(dev, "failed to allocate driver pdata\n");
If the system is OOM, this sort of error message will be pretty
redundant. Just return -ENOMEM instead.
> + return -ENOMEM;
> + }
> +
> + error = matrix_keypad_parse_of_params(dev, &pdata->num_out_pads,
> + &pdata->num_in_pads);
> + if (error) {
> + dev_err(dev, "failed to parse keypad params\n");
> + return error;
Nit: It's pretty unusual to use this for a standard error handling
variable. Consider 'ret' or 'err' as a replacement.
> + }
> +
> + of_property_read_u32(np, "st,debounce_us", &pdata->debounce_us);
Isn't this a required property? Might be worth checking the return
value if so.
> + st_kp->config = pdata;
> +
> + dev_info(dev, "rows=%d col=%d debounce=%d\n",
> + pdata->num_out_pads,
> + pdata->num_in_pads,
> + pdata->debounce_us);
Might be worth moving this down passed the final point of failure.
> + error = of_property_read_u32_array(np, "linux,keymap",
> + st_kp->keycodes, ST_KEYSCAN_MAXKEYS);
> + if (error) {
> + dev_err(dev, "failed to parse keymap\n");
> + return error;
> + }
> +
> + return 0;
> +}
> +
> +static int __init keyscan_probe(struct platform_device *pdev)
> +{
> + struct keypad_platform_data *pdata =
> + dev_get_platdata(&pdev->dev);
Do we really support platform data still?
> + struct keyscan_priv *st_kp;
> + struct input_dev *input_dev;
> + struct device *dev = &pdev->dev;
dev and pdev are used randomly in probe(). Just remove the dev
de-reference and use &pdev->dev exclusively.
It's pretty common to de-reference 'np = pdev->dev.of_node' though.
> + struct resource *res;
> + int len;
> + int error;
> + int i;
> +
> + if (!pdata && !pdev->dev.of_node) {
> + dev_err(&pdev->dev, "no keymap defined\n");
> + return -EINVAL;
> + }
> +
> + st_kp = devm_kzalloc(dev, sizeof(*st_kp), GFP_KERNEL);
> + if (!st_kp) {
> + dev_err(dev, "failed to allocate driver data\n");
> + return -ENOMEM;
I wouldn't print any messages on -ENOMEM personally. It's not a driver
failure per se, but a system one where the user will soon be notified.
> + }
> + st_kp->config = pdata;
You only want to do this in the !np case.
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (!res) {
> + dev_err(dev, "no I/O memory specified\n");
> + return -ENXIO;
> + }
> +
> + len = resource_size(res);
> + if (!devm_request_mem_region(dev, res->start, len, pdev->name)) {
> + dev_err(dev, "failed to reserve I/O memory\n");
> + return -EBUSY;
> + }
> +
> + st_kp->base = devm_ioremap_nocache(dev, res->start, len);
> + if (st_kp->base == NULL) {
> + dev_err(dev, "failed to remap I/O memory\n");
> + return -ENXIO;
> + }
Replace the two above with devm_ioremap_resource().
Make sure the IORESOURCE_CACHEABLE is set.
> + st_kp->irq = platform_get_irq(pdev, 0);
> + if (st_kp->irq < 0) {
> + dev_err(dev, "no IRQ specified\n");
> + return -ENXIO;
No such device or address, are you sure?
Perhaps -EINVAL would be better, as one should be specified.
> + }
> +
> + error = devm_request_irq(dev, st_kp->irq, keyscan_isr, 0,
> + pdev->name, pdev);
> + if (error) {
> + dev_err(dev, "failed to request IRQ\n");
> + return error;
> + }
> +
> + input_dev = devm_input_allocate_device(&pdev->dev);
> + if (!input_dev) {
> + dev_err(&pdev->dev, "failed to allocate the input device\n");
> + return -ENOMEM;
> + }
> +
> + st_kp->clk = devm_clk_get(dev, NULL);
> + if (IS_ERR(st_kp->clk)) {
> + dev_err(dev, "cannot get clock");
> + return PTR_ERR(st_kp->clk);
> + }
> +
> + input_dev = input_allocate_device();
> + if (!input_dev) {
> + dev_err(dev, "failed to allocate input device\n");
> + return -ENOMEM;
> + }
Wasn't this done already?
> + st_kp->input_dev = input_dev;
> +
> + input_dev->name = pdev->name;
> + input_dev->phys = "keyscan-keys/input0";
> + input_dev->dev.parent = dev;
> +
> + input_dev->id.bustype = BUS_HOST;
> + input_dev->id.vendor = 0x0001;
> + input_dev->id.product = 0x0001;
> + input_dev->id.version = 0x0100;
Any chance we can #define these?
> + if (!pdata) {
> + error = keypad_matrix_key_parse_dt(st_kp);
> + if (error)
> + return error;
> + pdata = st_kp->config;
Is pdata used after this?
> + }
> +
> + input_dev->keycode = st_kp->keycodes;
> + input_dev->keycodesize = sizeof(st_kp->keycodes[0]);
> + input_dev->keycodemax = ARRAY_SIZE(st_kp->keycodes);
> +
> + for (i = 0; i < ST_KEYSCAN_MAXKEYS; i++)
> + input_set_capability(input_dev, EV_KEY, st_kp->keycodes[i]);
> + __clear_bit(KEY_RESERVED, input_dev->keybit);
> +
> + error = input_register_device(input_dev);
> + if (error) {
> + dev_err(dev, "failed to register input device\n");
> + input_free_device(input_dev);
> + platform_set_drvdata(pdev, NULL);
You don't need to do this anymore. It's taken care of elsewhere.
> + return error;
> + }
> +
> + platform_set_drvdata(pdev, st_kp);
> +
> + keyscan_start(st_kp);
> +
> + device_set_wakeup_capable(&pdev->dev, 1);
> +
> + return 0;
> +}
> +
> +static int __exit keyscan_remove(struct platform_device *pdev)
> +{
> + struct keyscan_priv *priv = platform_get_drvdata(pdev);
> +
> + keyscan_stop(priv);
> +
> + input_unregister_device(priv->input_dev);
> + platform_set_drvdata(pdev, NULL);
> +
> + return 0;
I already saw that Dmitry commented on the rest of the file.
<snip>
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
