On Wed, Jan 22, 2014 at 10:54 +0800, thloh@xxxxxxxxxx wrote:
>
> From: Tien Hock Loh <thloh@xxxxxxxxxx>
>
> Add driver support for Altera GPIO soft IP, including interrupts and I/O.
> Tested on Altera CV SoC board using dipsw and LED using LED framework.
>
> Signed-off-by: Tien Hock Loh <thloh@xxxxxxxxxx>
> ---
> .../devicetree/bindings/gpio/gpio-altera.txt | 42 +++
> drivers/gpio/Kconfig | 7 +
> drivers/gpio/Makefile | 1 +
> drivers/gpio/gpio-altera.c | 420 +++++++++++++++++++++
> 4 files changed, 470 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/gpio/gpio-altera.txt
> create mode 100644 drivers/gpio/gpio-altera.c
Since you not only introduce the driver, but do introduce the
binding as well, I'd suggest to reflect this in the commit
message. And put 'binding' into the subject line such that DT
people can be aware they should have a look.
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/gpio-altera.txt
> @@ -0,0 +1,42 @@
> +Altera GPIO controller bindings
> +
> +Required properties:
> +- compatible:
> + - "altr,pio-1.0"
> +- reg: Physical base address and length of the controller's registers.
> +- #gpio-cells : Should be 1
> + - The first cell is the gpio offset number
> +- gpio-controller : Marks the device node as a GPIO controller.
Learning about required data types when reading the binding would
be nice. So that DTS authors can tell whether a property is
boolean, takes integers or strings, etc
> +- #interrupt-cells : Should be 1.
> + - The first cell is the GPIO offset number within the GPIO controller.
> +- interrupts: Specify the interrupt.
> +- interrupt-controller: Mark the device node as an interrupt controller
Are these really 'required'? I'd expect those to be optional.
> +
> +Altera GPIO specific properties:
> +- altr,gpio-bank-width: Width of the GPIO bank. This defines how many pins the
> + GPIO device has. Ranges between 1-32. Optional and defaults to 32 is not
> + specified.
In addition to being specific to the Altera GPIO implementation,
aren't these optional, too?
> +- altr,interrupt_trigger: Specifies the interrupt trigger type the GPIO
> + hardware is synthesized. This field is required if the Altera GPIO controller
> + used has IRQ enabled as the interrupt type is not software controlled,
> + but hardware synthesized. Required if GPIO is used as an interrupt
> + controller. The value is defined in <dt-bindings/interrupt-controller/irq.h>
> + Only the following flags are supported:
> + IRQ_TYPE_EDGE_RISING
> + IRQ_TYPE_EDGE_FALLING
> + IRQ_TYPE_EDGE_BOTH
> + IRQ_TYPE_LEVEL_HIGH
This text suggests that using the GPIO bank as an interrupt
controller indeed is optional. As one would expect.
> +
> +Example:
> +
> +gpio_altr: gpio_altr {
Should node names not be generic, i.e. "gpio"? While aliases do
have specific names since they identify a specific node, to later
reference it from other sites.
> + compatible = "altr,pio-1.0";
> + reg = <0xff200000 0x10>;
> + interrupts = <0 45 4>;
> + altr,gpio-bank-width = <32>;
> + altr,interrupt_trigger = <IRQ_TYPE_EDGE_RISING>;
> + #gpio-cells = <1>;
> + gpio-controller;
> + #interrupt-cells = <1>;
> + interrupt-controller;
> +};
virtually yours
Gerhard Sittig
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr. 5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office@xxxxxxx
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
