On Mon, Jan 20, 2014 at 3:45 PM, Sergei Shtylyov <sergei.shtylyov@xxxxxxxxxxxxxxxxxx> wrote: > On 01/20/2014 05:06 PM, Rob Herring wrote: > >>> This patch is an attempt to gather the Ethernet related bindings in one >>> file, >>> like it's done in the MMC and some other subsystems. It should save the >>> trouble >>> of documenting several properties over and over in each binding document. > > >>> I have used the Embedded Power Architecture(TM) Platform Requirements >>> (ePAPR) >>> standard as a base for the properties description, also documenting some >>> ad-hoc >>> properties that have been introduced over time despite having direct >>> analogs in >>> ePAPR. > > >>> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@xxxxxxxxxxxxxxxxxx> > > >>> --- >>> The patch is against DaveM's 'net-next.git' repo and the DaVinci EMAC >>> bindings >>> fix I've posted yesterday: > > >>> http://patchwork.ozlabs.org/patch/311854/ > > > [...] >>> Index: net-next/Documentation/devicetree/bindings/net/ethernet.txt >>> =================================================================== >>> --- /dev/null >>> +++ net-next/Documentation/devicetree/bindings/net/ethernet.txt >>> @@ -0,0 +1,20 @@ >>> +The following properties are common to the Ethernet controllers: >>> + >>> +- local-mac-address: array of 6 bytes, specifies the MAC address that >>> was >>> + assigned to the network device; >>> +- mac-address: array of 6 bytes, specifies the MAC address that was last >>> used by >>> + the boot program; should be used in cases where the MAC address >>> assigned to >>> + the device by the boot program is different from the >>> "local-mac-address" >>> + property; >>> +- max-speed: number, specifies maximum speed in Mbit/s supported by the >>> device; >>> +- phy-mode: string, operation mode of the PHY interface; supported >>> values are >>> + "mii", "gmii", "sgmii", "tbi", "rev-mii", "rmii", "rgmii", "rgmii-id", >>> + "rgmii-rxid", "rgmii-txid", "rtbi", "smii", "xgmii"; > > >> Mark this as deprecated > > > That's kind of wishful thinking at this point, as that's what the > majority of drivers use. I'm unsure of the reasons why that was done, > probably people just didn't read the proper specs... Or the spec was defined after those bindings. Deprecating does not matter for existing bindings. It's only defining new ones that are affected. I was more concerned with giving people guidance on which one to use for new bindings. >> in favor of phy-connection-type > > > That one is only used by the oldish PowerPC 'gianfar' driver. > > >> so it's use does not spread. > > > I'm afraid that's too late, it has spread very far, so that > of_get_phy_mode() handles that property, not "phy-connection-type". Uggg, I guess this is a case of a defacto standard then if the kernel doesn't even support it. >>> +- phy-connection-type: the same as "phy-mode" property (but described in >>> ePAPR); >>> +- phy-handle: phandle, specifies a reference to a node representing a >>> PHY >>> + device (this property is described in ePAPR); >>> +- phy: the same as "phy-handle" property (but actually ad-hoc one). > > >> Mark this as deprecated in favor of phy-handle. > > > Here situation is more optimistic. Quite many drivers still use > "phy-handle", though some use even more exotic props I didn't document here. Perhaps flagging as "Not recommended for new bindings" would be nicer wording... Rob -- To unsubscribe from this list: send the line "unsubscribe linux-doc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
