On 14-01-07 09:15 AM, Linus Walleij wrote:
On Sat, Dec 21, 2013 at 3:13 AM, Sherman Yin <syin@xxxxxxxxxxxx> wrote:
+Optional Properties (for standard pins):
+
+- function: String. Specifies the pin mux selection. Values
+ must be one of: "alt1", "alt2", "alt3", "alt4"
+- input-schmitt-enable: No arguments. Enable schmitt-trigger mode.
+- input-schmitt-disable: No arguments. Disable schmitt-trigger mode.
+- bias-pull-up: No arguments. Pull up on pin.
+- bias-pull-down: No arguments. Pull down on pin.
+- bias-disable: No arguments. Disable pin bias.
+- slew-rate: Integer. Meaning depends on configured pin mux:
+ *_SCL or *_SDA:
+ 0: Standard(100kbps)& Fast(400kbps) mode
+ 1: Highspeed (3.4Mbps) mode
+ IC_DM or IC_DP:
+ 0: normal slew rate
+ 1: fast slew rate
+ Otherwise:
+ 0: fast slew rate
+ 1: normal slew rate
+- input-enable: No arguements. Enable input (does not affect
+ output.)
+- input-disable: No arguements. Disable input (does not affect
+ output.)
+- drive-strength: Integer. Drive strength in mA. Valid values are
+ 2, 4, 6, 8, 10, 12, 14, 16 mA.
Also patch
Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
Since you're adding generic properties.
Please note that I removed from this patchset the patch that you've
merged to your for-next branch already:
https://git.kernel.org/cgit/linux/kernel/git/linusw/linux-pinctrl.git/commit/?h=for-next&id=8ba3f4d00078e7a49c60c0bd6298f29402c3a0a0
Is that what you wanted to see in pinctrl-bindings.txt, or is there
something else you want to see added to that txt file? I didn't want to
add the description of slew-rate arguments there because this is
capri-specific. I'm not quite sure what else to add.
+Optional Properties (for I2C pins):
+
+- function: String. Specifies the pin mux selection. Values
+ must be one of: "alt1", "alt2", "alt3", "alt4"
+- bias-pull-up: Integer. Pull up strength in Ohm. There are 3
+ pull-up resisitors (1.2k, 1.8k, 2.7k) available
+ in parallel for I2C pins, so the valid values
+ are: 568, 720, 831, 1080, 1200, 1800, 2700 Ohm.
Also patch
Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
That doc already says bias-pull-up is specified in Ohm, and the specific
values are chip-specific, so I don't think they should be mentioned there.
+- bias-disable: No arguments. Disable pin bias.
+- slew-rate: Integer. Meaning depends on configured pin mux:
+ *_SCL or *_SDA:
+ 0: Standard(100kbps)& Fast(400kbps) mode
+ 1: Highspeed (3.4Mbps) mode
+ IC_DM or IC_DP:
+ 0: normal slew rate
+ 1: fast slew rate
+ Otherwise:
+ 0: fast slew rate
+ 1: normal slew rate
Hm that does not seem generic though, so let's not add this to the
generic bindings.
+- input-enable: No arguements. Enable input (does not affect
+ output.)
+- input-disable: No arguements. Disable input (does not affect
+ output.)
+
+Optional Properties (for HDMI pins):
+
+- function: String. Specifies the pin mux selection. Values
+ must be one of: "alt1", "alt2", "alt3", "alt4"
+- slew-rate: Integer. Controls slew rate.
+ 0: Standard(100kbps)& Fast(400kbps) mode
+ 1: Highspeed (3.4Mbps) mode
Hmmmm slew rate is not specifiec in "bps" but rather in
something like volts per second. But maybe it's best to keep
this value driver-specific.
Right, I think the slew-rates values are capri specific.
Thanks for the review.
Regards,
Sherman
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
