Hi All,
On Wed, Dec 4, 2013 at 3:39 PM, Vivek Gautam <gautam.vivek@xxxxxxxxxxx> wrote:
> Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
> The new driver uses the generic PHY framework and will interact
> with DWC3 controller present on Exynos5 series of SoCs.
> Thereby, removing old phy-samsung-usb3 driver and related code
> used untill now which was based on usb/phy framework.
>
> Signed-off-by: Vivek Gautam <gautam.vivek@xxxxxxxxxxx>
> ---
a humble ping !! :-)
Any comments on this patch ?
> .../devicetree/bindings/phy/samsung-phy.txt | 43 ++
> drivers/phy/Kconfig | 8 +
> drivers/phy/Makefile | 1 +
> drivers/phy/phy-exynos5-usb3.c | 545 ++++++++++++++++++++
> drivers/usb/phy/Kconfig | 10 +-
> drivers/usb/phy/Makefile | 1 -
> drivers/usb/phy/phy-samsung-usb.h | 80 ---
> drivers/usb/phy/phy-samsung-usb3.c | 350 -------------
> 8 files changed, 598 insertions(+), 440 deletions(-)
> create mode 100644 drivers/phy/phy-exynos5-usb3.c
> delete mode 100644 drivers/usb/phy/phy-samsung-usb3.c
>
> diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt
> index c0fccaa..bcd95dd 100644
> --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
> +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
> @@ -20,3 +20,46 @@ Required properties:
> - compatible : should be "samsung,exynos5250-dp-video-phy";
> - reg : offset and length of the Display Port PHY register set;
> - #phy-cells : from the generic PHY bindings, must be 0;
> +
> +Samsung Exynos5 SoC series USB 3.0 PHY controller
> +--------------------------------------------------
> +
> +Required properties:
> +- compatible : Should be set to one of the following supported values:
> + - "samsung,exynos5250-usb3phy" - for exynos5250 SoC,
> + - "samsung,exynos5420-usb3phy" - for exynos5420 SoC.
> +- reg : Register offset and length of USB 3.0 PHY register set;
> +- clocks: Clock IDs array as required by the controller
> +- clock-names: names of clocks correseponding to IDs in the clock property;
> + Required clocks:
> + - phy: main PHY clock (same as USB 3.0 controller IP clock),
> + used for register access.
> + - usb3phy_refclk: PHY's reference clock (usually crystal clock), associated
> + by phy name, used to determine bit values for clock
> + settings register.
> + Additional clock required for Exynos5420:
> + - usb30_sclk_100m: Additional special clock used for PHY operation
> + depicted as 'sclk_usbphy30' in CMU of Exynos5420.
> +- samsung,syscon-phandle: phandle for syscon interface, which is used to
> + control pmu registers for power isolation.
> +- #phy-cells : from the generic PHY bindings, must be 0;
> +
> +Example:
> + usb3_phy: usbphy@12100000 {
> + compatible = "samsung,exynos5250-usb3phy";
> + reg = <0x12100000 0x100>;
> + clocks = <&clock 286>, <&clock 1>;
> + clock-names = "phy", "usb3phy_refclk";
> + samsung,syscon-phandle = <&pmu_syscon>;
> + #phy-cells = <0>;
> + };
> +
> +- aliases: For SoCs like Exynos5420 having multiple USB PHY controllers,
> + 'usb3_phy' nodes should have numbered alias in the aliases node,
> + in the form of usb3phyN, N = 0, 1... (depending on number of
> + controllers).
> +Example:
> + aliases {
> + usb3phy0 = &usb3_phy0;
> + usb3phy1 = &usb3_phy1;
> + };
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index a344f3d..67e9045 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -51,4 +51,12 @@ config PHY_EXYNOS_DP_VIDEO
> help
> Support for Display Port PHY found on Samsung EXYNOS SoCs.
>
> +config PHY_EXYNOS5_USB3
> + tristate "Exynos5 SoC series USB 3.0 PHY driver"
> + depends on ARCH_EXYNOS5
> + select GENERIC_PHY
> + select MFD_SYSCON
> + help
> + Enable USB 3.0 PHY support for Exynos 5 SoC series
> +
> endmenu
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index d0caae9..9c06a61 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -7,3 +7,4 @@ obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) += phy-exynos-dp-video.o
> obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
> obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
> obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
> +obj-$(CONFIG_PHY_EXYNOS5_USB3) += phy-exynos5-usb3.o
> diff --git a/drivers/phy/phy-exynos5-usb3.c b/drivers/phy/phy-exynos5-usb3.c
> new file mode 100644
> index 0000000..2bafc9d
> --- /dev/null
> +++ b/drivers/phy/phy-exynos5-usb3.c
> @@ -0,0 +1,545 @@
> +/*
> + * Samsung EXYNOS5 SoC series USB 3.0 PHY driver
> + *
> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> + * Author: Vivek Gautam <gautam.vivek@xxxxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/mutex.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/regmap.h>
> +
> +/* Exynos USB PHY registers */
> +#define EXYNOS5_FSEL_9MHZ6 0x0
> +#define EXYNOS5_FSEL_10MHZ 0x1
> +#define EXYNOS5_FSEL_12MHZ 0x2
> +#define EXYNOS5_FSEL_19MHZ2 0x3
> +#define EXYNOS5_FSEL_20MHZ 0x4
> +#define EXYNOS5_FSEL_24MHZ 0x5
> +#define EXYNOS5_FSEL_50MHZ 0x7
> +
> +/* EXYNOS5: USB 3.0 DRD PHY registers */
> +#define EXYNOS5_DRD_LINKSYSTEM (0x04)
> +
> +#define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
> +#define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
> +#define LINKSYSTEM_XHCI_VERSION_CONTROL (0x1 << 27)
> +
> +#define EXYNOS5_DRD_PHYUTMI (0x08)
> +
> +#define PHYUTMI_OTGDISABLE (0x1 << 6)
> +#define PHYUTMI_FORCESUSPEND (0x1 << 1)
> +#define PHYUTMI_FORCESLEEP (0x1 << 0)
> +
> +#define EXYNOS5_DRD_PHYPIPE (0x0c)
> +
> +#define EXYNOS5_DRD_PHYCLKRST (0x10)
> +
> +#define PHYCLKRST_EN_UTMISUSPEND (0x1 << 31)
> +
> +#define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23)
> +#define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23)
> +
> +#define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21)
> +#define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21)
> +
> +#define PHYCLKRST_SSC_EN (0x1 << 20)
> +#define PHYCLKRST_REF_SSP_EN (0x1 << 19)
> +#define PHYCLKRST_REF_CLKDIV2 (0x1 << 18)
> +
> +#define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x32 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
> +
> +#define PHYCLKRST_FSEL_MASK (0x3f << 5)
> +#define PHYCLKRST_FSEL(_x) ((_x) << 5)
> +#define PHYCLKRST_FSEL_PAD_100MHZ (0x27 << 5)
> +#define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5)
> +#define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5)
> +#define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5)
> +
> +#define PHYCLKRST_RETENABLEN (0x1 << 4)
> +
> +#define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2)
> +#define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2)
> +#define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2)
> +
> +#define PHYCLKRST_PORTRESET (0x1 << 1)
> +#define PHYCLKRST_COMMONONN (0x1 << 0)
> +
> +#define EXYNOS5_DRD_PHYREG0 (0x14)
> +#define EXYNOS5_DRD_PHYREG1 (0x18)
> +
> +#define EXYNOS5_DRD_PHYPARAM0 (0x1c)
> +
> +#define PHYPARAM0_REF_USE_PAD (0x1 << 31)
> +#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26)
> +#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26)
> +
> +#define EXYNOS5_DRD_PHYPARAM1 (0x20)
> +
> +#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
> +#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
> +
> +#define EXYNOS5_DRD_PHYTERM (0x24)
> +
> +#define EXYNOS5_DRD_PHYTEST (0x28)
> +
> +#define PHYTEST_POWERDOWN_SSP (0x1 << 3)
> +#define PHYTEST_POWERDOWN_HSP (0x1 << 2)
> +
> +#define EXYNOS5_DRD_PHYADP (0x2c)
> +
> +#define EXYNOS5_DRD_PHYBATCHG (0x30)
> +
> +#define PHYBATCHG_UTMI_CLKSEL (0x1 << 2)
> +
> +#define EXYNOS5_DRD_PHYRESUME (0x34)
> +#define EXYNOS5_DRD_LINKPORT (0x44)
> +
> +/* Power isolation defined in power management unit */
> +#define EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET (0x704)
> +#define EXYNOS5_USB3DRD_PMU_ISOL (1 << 0)
> +
> +#define KHZ 1000
> +#define MHZ (KHZ * KHZ)
> +
> +struct usb3phy_config {
> + bool has_usb30_sclk;
> + u32 reg_pmu_offset;
> + bool has_multi_controller;
> +};
> +
> +struct usb3phy_driver {
> + struct device *dev;
> + void __iomem *reg_phy;
> + struct regmap *reg_isol;
> + const struct usb3phy_config *cfg;
> + struct clk *clk;
> + struct clk *usb30_sclk;
> + struct phy *phy;
> + u32 refclk;
> + unsigned long rate;
> + u32 channel;
> +};
> +
> +/*
> + * exynos5_rate_to_clk() converts the supplied clock rate to the value that
> + * can be written to the phy register.
> + */
> +static u32 exynos5_rate_to_clk(unsigned long rate)
> +{
> + unsigned int clksel;
> +
> + /* EXYNOS5_FSEL_MASK */
> +
> + switch (rate) {
> + case 9600 * KHZ:
> + clksel = EXYNOS5_FSEL_9MHZ6;
> + break;
> + case 10 * MHZ:
> + clksel = EXYNOS5_FSEL_10MHZ;
> + break;
> + case 12 * MHZ:
> + clksel = EXYNOS5_FSEL_12MHZ;
> + break;
> + case 19200 * KHZ:
> + clksel = EXYNOS5_FSEL_19MHZ2;
> + break;
> + case 20 * MHZ:
> + clksel = EXYNOS5_FSEL_20MHZ;
> + break;
> + case 24 * MHZ:
> + clksel = EXYNOS5_FSEL_24MHZ;
> + break;
> + case 50 * MHZ:
> + clksel = EXYNOS5_FSEL_50MHZ;
> + break;
> + default:
> + clksel = -EINVAL;
> + }
> +
> + return clksel;
> +}
> +
> +static void exynos5_usb3phy_isol(struct usb3phy_driver *drv, unsigned int on)
> +{
> + u32 pmu_offset = drv->cfg->reg_pmu_offset;
> +
> + if (!drv->reg_isol)
> + return;
> +
> + switch (drv->channel) {
> + case 1:
> + /* Channel 1 is at 0x708 offset */
> + pmu_offset += sizeof(&pmu_offset);
> + break;
> + case 0:
> + default:
> + /* Channel 0 is at 0x704 offset */
> + break;
> + }
> +
> + regmap_update_bits(drv->reg_isol, pmu_offset,
> + EXYNOS5_USB3DRD_PMU_ISOL, ~on);
> +}
> +
> +/*
> + * Sets the phy clk as EXTREFCLK (XXTI) which is internal clock from clock core.
> + */
> +static u32 exynos5_usb3phy_set_refclk(struct usb3phy_driver *drv)
> +{
> + u32 reg;
> +
> + reg = PHYCLKRST_REFCLKSEL_EXT_REFCLK |
> + PHYCLKRST_FSEL(drv->refclk);
> +
> + switch (drv->refclk) {
> + case EXYNOS5_FSEL_50MHZ:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x00));
> + break;
> + case EXYNOS5_FSEL_24MHZ:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x88));
> + break;
> + case EXYNOS5_FSEL_20MHZ:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x00));
> + break;
> + case EXYNOS5_FSEL_19MHZ2:
> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
> + PHYCLKRST_SSC_REFCLKSEL(0x88));
> + break;
> + default:
> + dev_dbg(drv->dev, "unsupported ref clk\n");
> + break;
> + }
> +
> + return reg;
> +}
> +
> +static int exynos5_usb3phy_init(struct phy *phy)
> +{
> + struct usb3phy_driver *drv = phy_get_drvdata(phy);
> + int ret;
> + u32 phyparam0;
> + u32 phyparam1;
> + u32 linksystem;
> + u32 phybatchg;
> + u32 phytest;
> + u32 phyclkrst;
> +
> + ret = clk_prepare_enable(drv->clk);
> + if (ret)
> + return ret;
> +
> + /* Reset USB 3.0 PHY */
> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYREG0);
> +
> + phyparam0 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
> + /* Select PHY CLK source */
> + phyparam0 &= ~PHYPARAM0_REF_USE_PAD;
> + /* Set Loss-of-Signal Detector sensitivity */
> + phyparam0 &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
> + phyparam0 |= PHYPARAM0_REF_LOSLEVEL;
> + writel(phyparam0, drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
> +
> + writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYRESUME);
> +
> + /*
> + * Setting the Frame length Adj value[6:1] to default 0x20
> + * See xHCI 1.0 spec, 5.2.4
> + */
> + linksystem = LINKSYSTEM_XHCI_VERSION_CONTROL |
> + LINKSYSTEM_FLADJ(0x20);
> + writel(linksystem, drv->reg_phy + EXYNOS5_DRD_LINKSYSTEM);
> +
> + phyparam1 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
> + /* Set Tx De-Emphasis level */
> + phyparam1 &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
> + phyparam1 |= PHYPARAM1_PCS_TXDEEMPH;
> + writel(phyparam1, drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
> +
> + phybatchg = readl(drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
> + phybatchg |= PHYBATCHG_UTMI_CLKSEL;
> + writel(phybatchg, drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
> +
> + /* PHYTEST POWERDOWN Control */
> + phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> + phytest &= ~(PHYTEST_POWERDOWN_SSP |
> + PHYTEST_POWERDOWN_HSP);
> + writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> +
> + /* UTMI Power Control */
> + writel(PHYUTMI_OTGDISABLE, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
> +
> + phyclkrst = exynos5_usb3phy_set_refclk(drv);
> +
> + phyclkrst |= PHYCLKRST_PORTRESET |
> + /* Digital power supply in normal operating mode */
> + PHYCLKRST_RETENABLEN |
> + /* Enable ref clock for SS function */
> + PHYCLKRST_REF_SSP_EN |
> + /* Enable spread spectrum */
> + PHYCLKRST_SSC_EN |
> + /* Power down HS Bias and PLL blocks in suspend mode */
> + PHYCLKRST_COMMONONN;
> +
> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +
> + udelay(10);
> +
> + phyclkrst &= ~PHYCLKRST_PORTRESET;
> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +
> + clk_disable_unprepare(drv->clk);
> +
> + return 0;
> +}
> +
> +static int exynos5_usb3phy_exit(struct phy *phy)
> +{
> + struct usb3phy_driver *drv = phy_get_drvdata(phy);
> + int ret;
> + u32 phyutmi;
> + u32 phyclkrst;
> + u32 phytest;
> +
> + ret = clk_prepare_enable(drv->clk);
> + if (ret)
> + return ret;
> +
> + phyutmi = PHYUTMI_OTGDISABLE |
> + PHYUTMI_FORCESUSPEND |
> + PHYUTMI_FORCESLEEP;
> + writel(phyutmi, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
> +
> + /* Resetting the PHYCLKRST enable bits to reduce leakage current */
> + phyclkrst = readl(drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> + phyclkrst &= ~(PHYCLKRST_REF_SSP_EN |
> + PHYCLKRST_SSC_EN |
> + PHYCLKRST_COMMONONN);
> + writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +
> + /* Control PHYTEST to remove leakage current */
> + phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> + phytest |= PHYTEST_POWERDOWN_SSP |
> + PHYTEST_POWERDOWN_HSP;
> + writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> +
> + clk_disable_unprepare(drv->clk);
> +
> + return 0;
> +}
> +
> +static int exynos5_usb3phy_power_on(struct phy *phy)
> +{
> + struct usb3phy_driver *drv = phy_get_drvdata(phy);
> +
> + dev_dbg(drv->dev, "Request to power_on usb3drd phy\n");
> +
> + if (!IS_ERR(drv->usb30_sclk))
> + clk_prepare_enable(drv->usb30_sclk);
> +
> + /* Power-on PHY*/
> + exynos5_usb3phy_isol(drv, 0);
> +
> + return 0;
> +}
> +
> +static int exynos5_usb3phy_power_off(struct phy *phy)
> +{
> + struct usb3phy_driver *drv = phy_get_drvdata(phy);
> +
> + dev_dbg(drv->dev, "Request to power_off usb3drd phy\n");
> +
> + /* Power-off the PHY */
> + exynos5_usb3phy_isol(drv, 1);
> +
> + if (!IS_ERR(drv->usb30_sclk))
> + clk_disable_unprepare(drv->usb30_sclk);
> +
> + return 0;
> +}
> +
> +static struct phy_ops exynos5_usb3phy_ops = {
> + .init = exynos5_usb3phy_init,
> + .exit = exynos5_usb3phy_exit,
> + .power_on = exynos5_usb3phy_power_on,
> + .power_off = exynos5_usb3phy_power_off,
> + .owner = THIS_MODULE,
> +};
> +
> +const struct usb3phy_config exynos5420_usb3phy_cfg = {
> + .has_usb30_sclk = true,
> + .reg_pmu_offset = EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET,
> + .has_multi_controller = true,
> +};
> +
> +const struct usb3phy_config exynos5250_usb3phy_cfg = {
> + .has_usb30_sclk = false,
> + .reg_pmu_offset = EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET,
> + .has_multi_controller = false,
> +};
> +
> +static const struct of_device_id exynos5_usb3phy_of_match[] = {
> + {
> + .compatible = "samsung,exynos5250-usb3phy",
> + .data = &exynos5250_usb3phy_cfg
> + }, {
> + .compatible = "samsung,exynos5420-usb3phy",
> + .data = &exynos5420_usb3phy_cfg
> + },
> + { },
> +};
> +
> +static int exynos5_usb3phy_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct device_node *node = dev->of_node;
> + struct usb3phy_driver *drv;
> + struct phy_provider *phy_provider;
> + struct resource *res;
> + struct clk *clk;
> + const struct of_device_id *match;
> + const struct usb3phy_config *cfg;
> +
> + /*
> + * Exynos systems are completely DT enabled,
> + * so lets not have any platform data support for this driver.
> + */
> + if (!node) {
> + dev_err(dev, "no device node found\n");
> + return -ENODEV;
> + }
> +
> + match = of_match_node(exynos5_usb3phy_of_match, pdev->dev.of_node);
> + if (!match) {
> + dev_err(dev, "of_match_node() failed\n");
> + return -EINVAL;
> + }
> + cfg = match->data;
> +
> + drv = devm_kzalloc(dev, sizeof(*drv), GFP_KERNEL);
> + if (!drv) {
> + dev_err(dev, "Failed to allocate memory\n");
> + return -ENOMEM;
> + }
> +
> + dev_set_drvdata(dev, drv);
> + drv->dev = dev;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + drv->reg_phy = devm_ioremap_resource(dev, res);
> + if (IS_ERR(drv->reg_phy)) {
> + dev_err(dev, "Failed to map register memory (phy)\n");
> + return PTR_ERR(drv->reg_phy);
> + }
> +
> + drv->cfg = cfg;
> +
> + /*
> + * Exynos5420 SoC has multiple channels for USB 3.0 PHY, with
> + * each having separate power control registers.
> + * 'drv->channel' facilitates to set such registers.
> + */
> + if (drv->cfg->has_multi_controller) {
> + drv->channel = of_alias_get_id(node, "usb3phy");
> + if (drv->channel < 0) {
> + dev_err(dev, "Invalid usb3drd phy node\n");
> + return -EINVAL;
> + }
> + }
> +
> + drv->reg_isol = syscon_regmap_lookup_by_phandle(dev->of_node,
> + "samsung,syscon-phandle");
> + if (IS_ERR(drv->reg_isol)) {
> + dev_err(dev, "Failed to map register memory (isolation)\n");
> + return PTR_ERR(drv->reg_isol);
> + }
> +
> + drv->clk = devm_clk_get(dev, "phy");
> + if (IS_ERR(drv->clk)) {
> + dev_err(dev, "Failed to get clock of phy controller\n");
> + return PTR_ERR(drv->clk);
> + }
> +
> + /*
> + * Exysno5420 SoC has an additional special clock, used for
> + * for USB 3.0 PHY operation, this clock goes to the PHY block
> + * as a reference clock to clock generation block of the controller,
> + * named as 'USB30_SCLK_100M'.
> + */
> + if (cfg->has_usb30_sclk) {
> + drv->usb30_sclk = devm_clk_get(dev, "usb30_sclk_100m");
> + if (IS_ERR(drv->usb30_sclk)) {
> + dev_err(dev, "Failed to get phy reference clock\n");
> + return PTR_ERR(drv->usb30_sclk);
> + }
> + }
> +
> + dev_dbg(dev, "Creating usb3drd phy\n");
> + drv->phy = devm_phy_create(dev, &exynos5_usb3phy_ops, NULL);
> + if (IS_ERR(drv->phy)) {
> + dev_err(drv->dev, "Failed to create usb3drd phy\n");
> + return PTR_ERR(drv->phy);
> + }
> +
> + phy_set_drvdata(drv->phy, drv);
> +
> + clk = clk_get(dev, "usb3phy_refclk");
> + if (IS_ERR(clk)) {
> + dev_err(dev, "Failed to get reference clock of usb3drd phy\n");
> + return PTR_ERR(clk);
> + }
> + drv->rate = clk_get_rate(clk);
> +
> + drv->refclk = exynos5_rate_to_clk(drv->rate);
> + if (drv->refclk == -EINVAL) {
> + dev_err(dev, "Clock rate (%ld) not supported\n",
> + drv->rate);
> + clk_put(clk);
> + return -EINVAL;
> + }
> + clk_put(clk);
> +
> + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> + if (IS_ERR(phy_provider)) {
> + dev_err(drv->dev, "Failed to register phy provider\n");
> + return PTR_ERR(phy_provider);
> + }
> +
> + return 0;
> +}
> +
> +static struct platform_driver exynos5_usb3phy_driver = {
> + .probe = exynos5_usb3phy_probe,
> + .driver = {
> + .of_match_table = exynos5_usb3phy_of_match,
> + .name = "exynos5-usb3phy",
> + .owner = THIS_MODULE,
> + }
> +};
> +
> +module_platform_driver(exynos5_usb3phy_driver);
> +MODULE_DESCRIPTION("Samsung EXYNOS5 series SoC USB 3.0 PHY driver");
> +MODULE_AUTHOR("Vivek Gautam <gautam.vivek@xxxxxxxxxxx>");
> +MODULE_LICENSE("GPL v2");
> +MODULE_ALIAS("platform:exynos5-usb3phy");
> diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
> index 08e2f39..629789d 100644
> --- a/drivers/usb/phy/Kconfig
> +++ b/drivers/usb/phy/Kconfig
> @@ -95,7 +95,7 @@ config SAMSUNG_USBPHY
> help
> Enable this to support Samsung USB phy helper driver for Samsung SoCs.
> This driver provides common interface to interact, for Samsung USB 2.0 PHY
> - driver and later for Samsung USB 3.0 PHY driver.
> + driver.
>
> config SAMSUNG_USB2PHY
> tristate "Samsung USB 2.0 PHY controller Driver"
> @@ -105,14 +105,6 @@ config SAMSUNG_USB2PHY
> Enable this to support Samsung USB 2.0 (High Speed) PHY controller
> driver for Samsung SoCs.
>
> -config SAMSUNG_USB3PHY
> - tristate "Samsung USB 3.0 PHY controller Driver"
> - select SAMSUNG_USBPHY
> - select USB_PHY
> - help
> - Enable this to support Samsung USB 3.0 (Super Speed) phy controller
> - for samsung SoCs.
> -
> config TWL6030_USB
> tristate "TWL6030 USB Transceiver Driver"
> depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
> diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
> index 022c1da..b7f304a 100644
> --- a/drivers/usb/phy/Makefile
> +++ b/drivers/usb/phy/Makefile
> @@ -18,7 +18,6 @@ obj-$(CONFIG_AM335X_PHY_USB) += phy-am335x.o
> obj-$(CONFIG_OMAP_USB3) += phy-omap-usb3.o
> obj-$(CONFIG_SAMSUNG_USBPHY) += phy-samsung-usb.o
> obj-$(CONFIG_SAMSUNG_USB2PHY) += phy-samsung-usb2.o
> -obj-$(CONFIG_SAMSUNG_USB3PHY) += phy-samsung-usb3.o
> obj-$(CONFIG_TWL6030_USB) += phy-twl6030-usb.o
> obj-$(CONFIG_USB_EHCI_TEGRA) += phy-tegra-usb.o
> obj-$(CONFIG_USB_GPIO_VBUS) += phy-gpio-vbus-usb.o
> diff --git a/drivers/usb/phy/phy-samsung-usb.h b/drivers/usb/phy/phy-samsung-usb.h
> index 68771bf..dd2a0b5 100644
> --- a/drivers/usb/phy/phy-samsung-usb.h
> +++ b/drivers/usb/phy/phy-samsung-usb.h
> @@ -155,86 +155,6 @@
>
> #define EXYNOS5_PHY_OTG_TUNE (0x40)
>
> -/* EXYNOS5: USB 3.0 DRD */
> -#define EXYNOS5_DRD_LINKSYSTEM (0x04)
> -
> -#define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
> -#define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
> -#define LINKSYSTEM_XHCI_VERSION_CONTROL (0x1 << 27)
> -
> -#define EXYNOS5_DRD_PHYUTMI (0x08)
> -
> -#define PHYUTMI_OTGDISABLE (0x1 << 6)
> -#define PHYUTMI_FORCESUSPEND (0x1 << 1)
> -#define PHYUTMI_FORCESLEEP (0x1 << 0)
> -
> -#define EXYNOS5_DRD_PHYPIPE (0x0c)
> -
> -#define EXYNOS5_DRD_PHYCLKRST (0x10)
> -
> -#define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23)
> -#define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23)
> -
> -#define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21)
> -#define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21)
> -
> -#define PHYCLKRST_SSC_EN (0x1 << 20)
> -#define PHYCLKRST_REF_SSP_EN (0x1 << 19)
> -#define PHYCLKRST_REF_CLKDIV2 (0x1 << 18)
> -
> -#define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11)
> -#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11)
> -#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x02 << 11)
> -#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11)
> -#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11)
> -#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
> -
> -#define PHYCLKRST_FSEL_MASK (0x3f << 5)
> -#define PHYCLKRST_FSEL(_x) ((_x) << 5)
> -#define PHYCLKRST_FSEL_PAD_100MHZ (0x27 << 5)
> -#define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5)
> -#define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5)
> -#define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5)
> -
> -#define PHYCLKRST_RETENABLEN (0x1 << 4)
> -
> -#define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2)
> -#define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2)
> -#define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2)
> -
> -#define PHYCLKRST_PORTRESET (0x1 << 1)
> -#define PHYCLKRST_COMMONONN (0x1 << 0)
> -
> -#define EXYNOS5_DRD_PHYREG0 (0x14)
> -#define EXYNOS5_DRD_PHYREG1 (0x18)
> -
> -#define EXYNOS5_DRD_PHYPARAM0 (0x1c)
> -
> -#define PHYPARAM0_REF_USE_PAD (0x1 << 31)
> -#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26)
> -#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26)
> -
> -#define EXYNOS5_DRD_PHYPARAM1 (0x20)
> -
> -#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
> -#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
> -
> -#define EXYNOS5_DRD_PHYTERM (0x24)
> -
> -#define EXYNOS5_DRD_PHYTEST (0x28)
> -
> -#define PHYTEST_POWERDOWN_SSP (0x1 << 3)
> -#define PHYTEST_POWERDOWN_HSP (0x1 << 2)
> -
> -#define EXYNOS5_DRD_PHYADP (0x2c)
> -
> -#define EXYNOS5_DRD_PHYBATCHG (0x30)
> -
> -#define PHYBATCHG_UTMI_CLKSEL (0x1 << 2)
> -
> -#define EXYNOS5_DRD_PHYRESUME (0x34)
> -#define EXYNOS5_DRD_LINKPORT (0x44)
> -
> #ifndef MHZ
> #define MHZ (1000*1000)
> #endif
> diff --git a/drivers/usb/phy/phy-samsung-usb3.c b/drivers/usb/phy/phy-samsung-usb3.c
> deleted file mode 100644
> index cc08192..0000000
> --- a/drivers/usb/phy/phy-samsung-usb3.c
> +++ /dev/null
> @@ -1,350 +0,0 @@
> -/* linux/drivers/usb/phy/phy-samsung-usb3.c
> - *
> - * Copyright (c) 2013 Samsung Electronics Co., Ltd.
> - * http://www.samsung.com
> - *
> - * Author: Vivek Gautam <gautam.vivek@xxxxxxxxxxx>
> - *
> - * Samsung USB 3.0 PHY transceiver; talks to DWC3 controller.
> - *
> - * This program is free software; you can redistribute it and/or modify
> - * it under the terms of the GNU General Public License version 2 as
> - * published by the Free Software Foundation.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> - * GNU General Public License for more details.
> - */
> -
> -#include <linux/module.h>
> -#include <linux/platform_device.h>
> -#include <linux/clk.h>
> -#include <linux/delay.h>
> -#include <linux/err.h>
> -#include <linux/io.h>
> -#include <linux/of.h>
> -#include <linux/usb/samsung_usb_phy.h>
> -#include <linux/platform_data/samsung-usbphy.h>
> -
> -#include "phy-samsung-usb.h"
> -
> -/*
> - * Sets the phy clk as EXTREFCLK (XXTI) which is internal clock from clock core.
> - */
> -static u32 samsung_usb3phy_set_refclk(struct samsung_usbphy *sphy)
> -{
> - u32 reg;
> - u32 refclk;
> -
> - refclk = sphy->ref_clk_freq;
> -
> - reg = PHYCLKRST_REFCLKSEL_EXT_REFCLK |
> - PHYCLKRST_FSEL(refclk);
> -
> - switch (refclk) {
> - case FSEL_CLKSEL_50M:
> - reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
> - PHYCLKRST_SSC_REFCLKSEL(0x00));
> - break;
> - case FSEL_CLKSEL_20M:
> - reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
> - PHYCLKRST_SSC_REFCLKSEL(0x00));
> - break;
> - case FSEL_CLKSEL_19200K:
> - reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
> - PHYCLKRST_SSC_REFCLKSEL(0x88));
> - break;
> - case FSEL_CLKSEL_24M:
> - default:
> - reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
> - PHYCLKRST_SSC_REFCLKSEL(0x88));
> - break;
> - }
> -
> - return reg;
> -}
> -
> -static void samsung_exynos5_usb3phy_enable(struct samsung_usbphy *sphy)
> -{
> - void __iomem *regs = sphy->regs;
> - u32 phyparam0;
> - u32 phyparam1;
> - u32 linksystem;
> - u32 phybatchg;
> - u32 phytest;
> - u32 phyclkrst;
> -
> - /* Reset USB 3.0 PHY */
> - writel(0x0, regs + EXYNOS5_DRD_PHYREG0);
> -
> - phyparam0 = readl(regs + EXYNOS5_DRD_PHYPARAM0);
> - /* Select PHY CLK source */
> - phyparam0 &= ~PHYPARAM0_REF_USE_PAD;
> - /* Set Loss-of-Signal Detector sensitivity */
> - phyparam0 &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
> - phyparam0 |= PHYPARAM0_REF_LOSLEVEL;
> - writel(phyparam0, regs + EXYNOS5_DRD_PHYPARAM0);
> -
> - writel(0x0, regs + EXYNOS5_DRD_PHYRESUME);
> -
> - /*
> - * Setting the Frame length Adj value[6:1] to default 0x20
> - * See xHCI 1.0 spec, 5.2.4
> - */
> - linksystem = LINKSYSTEM_XHCI_VERSION_CONTROL |
> - LINKSYSTEM_FLADJ(0x20);
> - writel(linksystem, regs + EXYNOS5_DRD_LINKSYSTEM);
> -
> - phyparam1 = readl(regs + EXYNOS5_DRD_PHYPARAM1);
> - /* Set Tx De-Emphasis level */
> - phyparam1 &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
> - phyparam1 |= PHYPARAM1_PCS_TXDEEMPH;
> - writel(phyparam1, regs + EXYNOS5_DRD_PHYPARAM1);
> -
> - phybatchg = readl(regs + EXYNOS5_DRD_PHYBATCHG);
> - phybatchg |= PHYBATCHG_UTMI_CLKSEL;
> - writel(phybatchg, regs + EXYNOS5_DRD_PHYBATCHG);
> -
> - /* PHYTEST POWERDOWN Control */
> - phytest = readl(regs + EXYNOS5_DRD_PHYTEST);
> - phytest &= ~(PHYTEST_POWERDOWN_SSP |
> - PHYTEST_POWERDOWN_HSP);
> - writel(phytest, regs + EXYNOS5_DRD_PHYTEST);
> -
> - /* UTMI Power Control */
> - writel(PHYUTMI_OTGDISABLE, regs + EXYNOS5_DRD_PHYUTMI);
> -
> - phyclkrst = samsung_usb3phy_set_refclk(sphy);
> -
> - phyclkrst |= PHYCLKRST_PORTRESET |
> - /* Digital power supply in normal operating mode */
> - PHYCLKRST_RETENABLEN |
> - /* Enable ref clock for SS function */
> - PHYCLKRST_REF_SSP_EN |
> - /* Enable spread spectrum */
> - PHYCLKRST_SSC_EN |
> - /* Power down HS Bias and PLL blocks in suspend mode */
> - PHYCLKRST_COMMONONN;
> -
> - writel(phyclkrst, regs + EXYNOS5_DRD_PHYCLKRST);
> -
> - udelay(10);
> -
> - phyclkrst &= ~(PHYCLKRST_PORTRESET);
> - writel(phyclkrst, regs + EXYNOS5_DRD_PHYCLKRST);
> -}
> -
> -static void samsung_exynos5_usb3phy_disable(struct samsung_usbphy *sphy)
> -{
> - u32 phyutmi;
> - u32 phyclkrst;
> - u32 phytest;
> - void __iomem *regs = sphy->regs;
> -
> - phyutmi = PHYUTMI_OTGDISABLE |
> - PHYUTMI_FORCESUSPEND |
> - PHYUTMI_FORCESLEEP;
> - writel(phyutmi, regs + EXYNOS5_DRD_PHYUTMI);
> -
> - /* Resetting the PHYCLKRST enable bits to reduce leakage current */
> - phyclkrst = readl(regs + EXYNOS5_DRD_PHYCLKRST);
> - phyclkrst &= ~(PHYCLKRST_REF_SSP_EN |
> - PHYCLKRST_SSC_EN |
> - PHYCLKRST_COMMONONN);
> - writel(phyclkrst, regs + EXYNOS5_DRD_PHYCLKRST);
> -
> - /* Control PHYTEST to remove leakage current */
> - phytest = readl(regs + EXYNOS5_DRD_PHYTEST);
> - phytest |= (PHYTEST_POWERDOWN_SSP |
> - PHYTEST_POWERDOWN_HSP);
> - writel(phytest, regs + EXYNOS5_DRD_PHYTEST);
> -}
> -
> -static int samsung_usb3phy_init(struct usb_phy *phy)
> -{
> - struct samsung_usbphy *sphy;
> - unsigned long flags;
> - int ret = 0;
> -
> - sphy = phy_to_sphy(phy);
> -
> - /* Enable the phy clock */
> - ret = clk_prepare_enable(sphy->clk);
> - if (ret) {
> - dev_err(sphy->dev, "%s: clk_prepare_enable failed\n", __func__);
> - return ret;
> - }
> -
> - spin_lock_irqsave(&sphy->lock, flags);
> -
> - /* setting default phy-type for USB 3.0 */
> - samsung_usbphy_set_type(&sphy->phy, USB_PHY_TYPE_DEVICE);
> -
> - /* Disable phy isolation */
> - if (sphy->drv_data->set_isolation)
> - sphy->drv_data->set_isolation(sphy, false);
> -
> - /* Initialize usb phy registers */
> - sphy->drv_data->phy_enable(sphy);
> -
> - spin_unlock_irqrestore(&sphy->lock, flags);
> -
> - /* Disable the phy clock */
> - clk_disable_unprepare(sphy->clk);
> -
> - return ret;
> -}
> -
> -/*
> - * The function passed to the usb driver for phy shutdown
> - */
> -static void samsung_usb3phy_shutdown(struct usb_phy *phy)
> -{
> - struct samsung_usbphy *sphy;
> - unsigned long flags;
> -
> - sphy = phy_to_sphy(phy);
> -
> - if (clk_prepare_enable(sphy->clk)) {
> - dev_err(sphy->dev, "%s: clk_prepare_enable failed\n", __func__);
> - return;
> - }
> -
> - spin_lock_irqsave(&sphy->lock, flags);
> -
> - /* setting default phy-type for USB 3.0 */
> - samsung_usbphy_set_type(&sphy->phy, USB_PHY_TYPE_DEVICE);
> -
> - /* De-initialize usb phy registers */
> - sphy->drv_data->phy_disable(sphy);
> -
> - /* Enable phy isolation */
> - if (sphy->drv_data->set_isolation)
> - sphy->drv_data->set_isolation(sphy, true);
> -
> - spin_unlock_irqrestore(&sphy->lock, flags);
> -
> - clk_disable_unprepare(sphy->clk);
> -}
> -
> -static int samsung_usb3phy_probe(struct platform_device *pdev)
> -{
> - struct samsung_usbphy *sphy;
> - struct samsung_usbphy_data *pdata = dev_get_platdata(&pdev->dev);
> - struct device *dev = &pdev->dev;
> - struct resource *phy_mem;
> - void __iomem *phy_base;
> - struct clk *clk;
> - int ret;
> -
> - phy_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> - phy_base = devm_ioremap_resource(dev, phy_mem);
> - if (IS_ERR(phy_base))
> - return PTR_ERR(phy_base);
> -
> - sphy = devm_kzalloc(dev, sizeof(*sphy), GFP_KERNEL);
> - if (!sphy)
> - return -ENOMEM;
> -
> - clk = devm_clk_get(dev, "usbdrd30");
> - if (IS_ERR(clk)) {
> - dev_err(dev, "Failed to get device clock\n");
> - return PTR_ERR(clk);
> - }
> -
> - sphy->dev = dev;
> -
> - if (dev->of_node) {
> - ret = samsung_usbphy_parse_dt(sphy);
> - if (ret < 0)
> - return ret;
> - } else {
> - if (!pdata) {
> - dev_err(dev, "no platform data specified\n");
> - return -EINVAL;
> - }
> - }
> -
> - sphy->plat = pdata;
> - sphy->regs = phy_base;
> - sphy->clk = clk;
> - sphy->phy.dev = sphy->dev;
> - sphy->phy.label = "samsung-usb3phy";
> - sphy->phy.type = USB_PHY_TYPE_USB3;
> - sphy->phy.init = samsung_usb3phy_init;
> - sphy->phy.shutdown = samsung_usb3phy_shutdown;
> - sphy->drv_data = samsung_usbphy_get_driver_data(pdev);
> -
> - sphy->ref_clk_freq = samsung_usbphy_get_refclk_freq(sphy);
> - if (sphy->ref_clk_freq < 0)
> - return -EINVAL;
> -
> - spin_lock_init(&sphy->lock);
> -
> - platform_set_drvdata(pdev, sphy);
> -
> - return usb_add_phy_dev(&sphy->phy);
> -}
> -
> -static int samsung_usb3phy_remove(struct platform_device *pdev)
> -{
> - struct samsung_usbphy *sphy = platform_get_drvdata(pdev);
> -
> - usb_remove_phy(&sphy->phy);
> -
> - if (sphy->pmuregs)
> - iounmap(sphy->pmuregs);
> - if (sphy->sysreg)
> - iounmap(sphy->sysreg);
> -
> - return 0;
> -}
> -
> -static struct samsung_usbphy_drvdata usb3phy_exynos5 = {
> - .cpu_type = TYPE_EXYNOS5250,
> - .devphy_en_mask = EXYNOS_USBPHY_ENABLE,
> - .rate_to_clksel = samsung_usbphy_rate_to_clksel_4x12,
> - .set_isolation = samsung_usbphy_set_isolation_4210,
> - .phy_enable = samsung_exynos5_usb3phy_enable,
> - .phy_disable = samsung_exynos5_usb3phy_disable,
> -};
> -
> -#ifdef CONFIG_OF
> -static const struct of_device_id samsung_usbphy_dt_match[] = {
> - {
> - .compatible = "samsung,exynos5250-usb3phy",
> - .data = &usb3phy_exynos5
> - },
> - {},
> -};
> -MODULE_DEVICE_TABLE(of, samsung_usbphy_dt_match);
> -#endif
> -
> -static struct platform_device_id samsung_usbphy_driver_ids[] = {
> - {
> - .name = "exynos5250-usb3phy",
> - .driver_data = (unsigned long)&usb3phy_exynos5,
> - },
> - {},
> -};
> -
> -MODULE_DEVICE_TABLE(platform, samsung_usbphy_driver_ids);
> -
> -static struct platform_driver samsung_usb3phy_driver = {
> - .probe = samsung_usb3phy_probe,
> - .remove = samsung_usb3phy_remove,
> - .id_table = samsung_usbphy_driver_ids,
> - .driver = {
> - .name = "samsung-usb3phy",
> - .owner = THIS_MODULE,
> - .of_match_table = of_match_ptr(samsung_usbphy_dt_match),
> - },
> -};
> -
> -module_platform_driver(samsung_usb3phy_driver);
> -
> -MODULE_DESCRIPTION("Samsung USB 3.0 phy controller");
> -MODULE_AUTHOR("Vivek Gautam <gautam.vivek@xxxxxxxxxxx>");
> -MODULE_LICENSE("GPL");
> -MODULE_ALIAS("platform:samsung-usb3phy");
> --
> 1.7.6.5
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-usb" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
Best Regards
Vivek Gautam
Samsung R&D Institute, Bangalore
India
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
