[PATCH 2/3] thermal: imx: add necessary clk operation

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Thermal sensor needs pll3_usb_otg when measuring temperature,
otherwise the temperature read will be incorrect, so need to
enable this clk before sensor working, for alarm function,
as hardware will take measurement periodically, so we should
keep this clk always on once alarm function is enabled.

Signed-off-by: Anson Huang <b20788@xxxxxxxxxxxxx>
---
 drivers/thermal/imx_thermal.c |   22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/drivers/thermal/imx_thermal.c b/drivers/thermal/imx_thermal.c
index 1d6c801..7abbc04 100644
--- a/drivers/thermal/imx_thermal.c
+++ b/drivers/thermal/imx_thermal.c
@@ -7,6 +7,7 @@
  *
  */
 
+#include <linux/clk.h>
 #include <linux/cpu_cooling.h>
 #include <linux/cpufreq.h>
 #include <linux/delay.h>
@@ -73,6 +74,7 @@ struct imx_thermal_data {
 	unsigned long last_temp;
 	bool irq_enabled;
 	int irq;
+	struct clk *thermal_clk;
 };
 
 static void imx_set_alarm_temp(struct imx_thermal_data *data,
@@ -427,6 +429,13 @@ static int imx_thermal_probe(struct platform_device *pdev)
 		return ret;
 	}
 
+	data->thermal_clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(data->thermal_clk)) {
+		ret = IS_ERR(data->thermal_clk);
+		dev_err(&pdev->dev, "failed to get thermal clk!\n");
+		return ret;
+	}
+
 	/* Make sure sensor is in known good state for measurements */
 	regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
 	regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_MEASURE_TEMP);
@@ -457,6 +466,19 @@ static int imx_thermal_probe(struct platform_device *pdev)
 		return ret;
 	}
 
+	/*
+	 * Thermal sensor needs clk on to get correct value, normally
+	 * we should enable its clk before taking measurement and disable
+	 * clk after measurement is done, but if alarm function is enabled,
+	 * hardware will auto measure the temperature periodically, so we
+	 * need to keep the clk always on for alarm function.
+	 */
+	ret = clk_prepare_enable(data->thermal_clk);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to enable thermal clk: %d\n", ret);
+		return ret;
+	}
+
 	/* Enable measurements at ~ 10 Hz */
 	regmap_write(map, TEMPSENSE1 + REG_CLR, TEMPSENSE1_MEASURE_FREQ);
 	measure_freq = DIV_ROUND_UP(32768, 10); /* 10 Hz */
-- 
1.7.9.5


--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux