Minor edits regarding use of spacing and proofreading.
Signed-off-by: Manuel Fombuena <fombuena@xxxxxxxxxxx>
---
drivers/leds/leds-st1202.c | 48 +++++++++++++++++++-------------------
1 file changed, 24 insertions(+), 24 deletions(-)
diff --git a/drivers/leds/leds-st1202.c b/drivers/leds/leds-st1202.c
index 927874f20839..cb4797ea8f3a 100644
--- a/drivers/leds/leds-st1202.c
+++ b/drivers/leds/leds-st1202.c
@@ -16,27 +16,27 @@
#include <linux/slab.h>
#include <linux/string.h>
-#define ST1202_CHAN_DISABLE_ALL 0x00
-#define ST1202_CHAN_ENABLE_HIGH 0x03
-#define ST1202_CHAN_ENABLE_LOW 0x02
-#define ST1202_CONFIG_REG 0x04
+#define ST1202_CHAN_DISABLE_ALL 0x00
+#define ST1202_CHAN_ENABLE_HIGH 0x03
+#define ST1202_CHAN_ENABLE_LOW 0x02
+#define ST1202_CONFIG_REG 0x04
/* PATS: Pattern sequence feature enable */
-#define ST1202_CONFIG_REG_PATS BIT(7)
+#define ST1202_CONFIG_REG_PATS BIT(7)
/* PATSR: Pattern sequence runs (self-clear when sequence is finished) */
-#define ST1202_CONFIG_REG_PATSR BIT(6)
-#define ST1202_CONFIG_REG_SHFT BIT(3)
-#define ST1202_DEV_ENABLE 0x01
-#define ST1202_DEV_ENABLE_ON BIT(0)
-#define ST1202_DEV_ENABLE_RESET BIT(7)
-#define ST1202_DEVICE_ID 0x00
-#define ST1202_ILED_REG0 0x09
-#define ST1202_MAX_LEDS 12
-#define ST1202_MAX_PATTERNS 8
-#define ST1202_MILLIS_PATTERN_DUR_MAX 5660
-#define ST1202_MILLIS_PATTERN_DUR_MIN 22
-#define ST1202_PATTERN_DUR 0x16
-#define ST1202_PATTERN_PWM 0x1E
-#define ST1202_PATTERN_REP 0x15
+#define ST1202_CONFIG_REG_PATSR BIT(6)
+#define ST1202_CONFIG_REG_SHFT BIT(3)
+#define ST1202_DEV_ENABLE 0x01
+#define ST1202_DEV_ENABLE_ON BIT(0)
+#define ST1202_DEV_ENABLE_RESET BIT(7)
+#define ST1202_DEVICE_ID 0x00
+#define ST1202_ILED_REG0 0x09
+#define ST1202_MAX_LEDS 12
+#define ST1202_MAX_PATTERNS 8
+#define ST1202_MILLIS_PATTERN_DUR_MAX 5660
+#define ST1202_MILLIS_PATTERN_DUR_MIN 22
+#define ST1202_PATTERN_DUR 0x16
+#define ST1202_PATTERN_PWM 0x1E
+#define ST1202_PATTERN_REP 0x15
struct st1202_led {
struct fwnode_handle *fwnode;
@@ -99,9 +99,9 @@ static int st1202_pwm_pattern_write(struct st1202_chip *chip, int led_num,
value_h = (u8)(value >> 8);
/*
- * Datasheet: Register address low = 1Eh + 2*(xh) + 18h*(yh),
- * where x is the channel number (led number) in hexadecimal (x = 00h .. 0Bh)
- * and y is the pattern number in hexadecimal (y = 00h .. 07h)
+ * Datasheet: Register address low = 1Eh + 2*(xh) + 18h*(yh),
+ * where x is the channel number (led number) in hexadecimal (x = 00h .. 0Bh)
+ * and y is the pattern number in hexadecimal (y = 00h .. 07h)
*/
ret = st1202_write_reg(chip, (ST1202_PATTERN_PWM + (led_num * 2) + 0x18 * pattern),
value_l);
@@ -288,8 +288,8 @@ static int st1202_setup(struct st1202_chip *chip)
guard(mutex)(&chip->lock);
/*
- * Once the supply voltage is applied, the LED1202 executes some internal checks,
- * afterwords it stops the oscillator and puts the internal LDO in quiescent mode.
+ * Once the supply voltage is applied, the LED1202 executes some internal checks.
+ * Afterwards, it stops the oscillator and puts the internal LDO in quiescent mode.
* To start the device, EN bit must be set inside the “Device Enable” register at
* address 01h. As soon as EN is set, the LED1202 loads the adjustment parameters
* from the internal non-volatile memory and performs an auto-calibration procedure
--
2.48.1
