Re: [PATCH v2 03/10] dt-bindings: iio: adc: ad7606: Add iio backend bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Sep 20, 2024 at 05:33:23PM +0000, Guillaume Stols wrote:
> Add the required properties for iio-backend support, as well as an
> example and the conditions to mutually exclude interruption and
> conversion trigger with iio-backend.
> The iio-backend's function is to controls the communication, and thus the
> interruption pin won't be available anymore.
> As a consequence, the conversion pin must be controlled externally since
> we will miss information about when every single conversion cycle (i.e
> conversion + data transfer) ends, hence a PWM is introduced to trigger
> the conversions.
> 
> Signed-off-by: Guillaume Stols <gstols@xxxxxxxxxxxx>
> ---
>  .../devicetree/bindings/iio/adc/adi,ad7606.yaml    | 76 +++++++++++++++++++++-
>  1 file changed, 74 insertions(+), 2 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
> index 12995ebcddc2..74a8680904b1 100644
> --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
> +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
> @@ -118,13 +118,32 @@ properties:
>        this property must be defined.
>      type: boolean
>  
> +  pwms:
> +    description:
> +      In case the conversion is triggered by a PWM instead of a GPIO plugged to
> +      the CONVST pin, the PWM must be referenced.
> +    minItems: 1
> +    maxItems: 2

Please use an items list to describe what each item is, rather than
doing so in the pwm-names description below.

> +
> +  pwm-names:
> +    description:
> +      The name of each PWM, the first is connected to CONVST, and the second is
> +      connected to CONVST2 if CONVST2 is available and not connected to CONVST1.
> +    minItems: 1
> +    maxItems: 2

You need to define what the names actually are, otherwise you have no
ABI.

Cheers,
Conor.

> +
> +  io-backends:
> +    description:
> +      A reference to the iio-backend, which is responsible handling the BUSY
> +      pin's falling edge and communication.
> +      An example of backend can be found at
> +      http://analogdevicesinc.github.io/hdl/library/axi_ad7606x/index.html
> +
>  required:
>    - compatible
>    - reg
>    - avcc-supply
>    - vdrive-supply
> -  - interrupts
> -  - adi,conversion-start-gpios
>  
>  oneOf:
>    - required:
> @@ -138,6 +157,34 @@ oneOf:
>            - spi-cpol
>  
>  allOf:
> +  - if:
> +      properties:
> +        pwms: false
> +    then:
> +      required:
> +        - adi,conversion-start-gpios
> +
> +  - if:
> +      properties:
> +        adi,conversion-start-gpios: false
> +    then:
> +      required:
> +        - pwms
> +
> +  - if:
> +      properties:
> +        interrupts: false
> +    then:
> +      required:
> +        - io-backends
> +
> +  - if:
> +      properties:
> +        io-backends: false
> +    then:
> +      required:
> +        - interrupts
> +
>    - if:
>        properties:
>          compatible:
> @@ -179,12 +226,37 @@ allOf:
>          adi,sw-mode: false
>      else:
>        properties:
> +        pwms:
> +          maxItems: 1
> +        pwm-names:
> +          maxItems: 1
>          adi,conversion-start-gpios:
>            maxItems: 1
>  
>  unevaluatedProperties: false
>  
>  examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +    / {
> +        adi_adc {
> +            compatible = "adi,ad7606b";
> +            parallel-interface;
> +            pwms = <&axi_pwm_gen 0 0>;
> +
> +            avcc-supply = <&adc_vref>;
> +            vdrive-supply = <&vdd_supply>;
> +
> +            reset-gpios = <&gpio0 91 GPIO_ACTIVE_HIGH>;
> +            standby-gpios = <&gpio0 90 GPIO_ACTIVE_LOW>;
> +            adi,range-gpios = <&gpio0 89 GPIO_ACTIVE_HIGH>;
> +            adi,oversampling-ratio-gpios = <&gpio0 88 GPIO_ACTIVE_HIGH
> +                                            &gpio0 87 GPIO_ACTIVE_HIGH
> +                                            &gpio0 86 GPIO_ACTIVE_HIGH>;
> +            io-backends = <&iio_backend>;
> +        };
> +    };
> +
>    - |
>      #include <dt-bindings/gpio/gpio.h>
>      #include <dt-bindings/interrupt-controller/irq.h>
> 
> -- 
> 2.34.1
> 

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux