Re: [PATCH v4 2/3] iio: adc: ad7625: add driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 2024-09-05 3:58 a.m., Nuno Sá wrote:
On Wed, 2024-09-04 at 15:14 -0400, Trevor Gamblin wrote:
Add a driver for the AD762x and AD796x family of ADCs. These are
pin-compatible devices using an LVDS interface for data transfer,
capable of sampling at rates of 6 (AD7625), 10 (AD7626), and 5
(AD7960/AD7961) MSPS, respectively. They also feature multiple voltage
reference options based on the configuration of the EN1/EN0 pins, which
can be set in the devicetree.

Signed-off-by: Trevor Gamblin <tgamblin@xxxxxxxxxxxx>
---
Hi Trevor,

It LGTM, just some minor stuff from me...

With that,

Reviewed-by: Nuno Sa <nuno.sa@xxxxxxxxxx>

  MAINTAINERS              |   1 +
  drivers/iio/adc/Kconfig  |  16 ++
  drivers/iio/adc/Makefile |   1 +
  drivers/iio/adc/ad7625.c | 684
+++++++++++++++++++++++++++++++++++++++++++++++

...

+
+static int ad7625_set_sampling_freq(struct ad7625_state *st, int freq)
+{
+	u64 target;
+	struct pwm_waveform clk_gate_wf = { }, cnv_wf = { };
+	int ret;
+
+	target = DIV_ROUND_UP_ULL(NSEC_PER_SEC, freq);
Not seeing any reason why it can't be DIV_ROUND_UP()?
Uwe rightly pointed out (internally) that freq probably shouldn't be signed, so I'll adjust that instead and resubmit.

+	cnv_wf.period_length_ns = clamp(target, 100, 10 * KILO);
+
+	/*
+	 * Use the maximum conversion time t_CNVH from the datasheet as
+	 * the duty_cycle for ref_clk, cnv, and clk_gate
+	 */
+	cnv_wf.duty_length_ns = st->info->timing_spec->conv_high_ns;
+
+	ret = pwm_round_waveform_might_sleep(st->cnv_pwm, &cnv_wf);
+	if (ret)
+		return ret;
+
+	/*
+	 * Set up the burst signal for transferring data. period and
+	 * offset should mirror the CNV signal
+	 */
+	clk_gate_wf.period_length_ns = cnv_wf.period_length_ns;
+
+	clk_gate_wf.duty_length_ns = DIV_ROUND_UP_ULL((u64)NSEC_PER_SEC *
+		st->info->chan_spec.scan_type.realbits,
+		st->ref_clk_rate_hz);
+
+	/* max t_MSB from datasheet */
+	clk_gate_wf.duty_offset_ns = st->info->timing_spec->conv_msb_ns;
+
+	ret = pwm_round_waveform_might_sleep(st->clk_gate_pwm, &clk_gate_wf);
+	if (ret)
+		return ret;
+
+	st->cnv_wf = cnv_wf;
+	st->clk_gate_wf = clk_gate_wf;
+
+	/* TODO: Add a rounding API for PWMs that can simplify this */
+	target = DIV_ROUND_CLOSEST_ULL(st->ref_clk_rate_hz, freq);
ditto...

+	st->sampling_freq_hz = DIV_ROUND_CLOSEST_ULL(st->ref_clk_rate_hz,
+						     target);
+
+	return 0;
+}
+

...

+
+static int ad7625_buffer_preenable(struct iio_dev *indio_dev)
+{
+	struct ad7625_state *st = iio_priv(indio_dev);
+	int ret;
+
+	ret = pwm_set_waveform_might_sleep(st->cnv_pwm, &st->cnv_wf, false);
+	if (ret)
+		return ret;
+
+	ret = pwm_set_waveform_might_sleep(st->clk_gate_pwm,
+					   &st->clk_gate_wf, false);
+	if (ret) {
+		/* Disable cnv PWM if clk_gate setup failed */
+		pwm_disable(st->cnv_pwm);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ad7625_buffer_postdisable(struct iio_dev *indio_dev)
+{
+	struct ad7625_state *st = iio_priv(indio_dev);
+
+	pwm_disable(st->cnv_pwm);
+	pwm_disable(st->clk_gate_pwm);
+
+	return 0;
+}
+
Might not matter but it is a good practise to disable things in the reverse
order.

Good point, I'll change that too.

Thanks!


- Nuno Sá






[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux