Hi Mauro, Mauro Ribeiro <mdrjr0@xxxxxxxxx> writes: > Kevin, > > https://github.com/hardkernel/u-boot/tree/odroid-v2012.07 Yes, this is the one I'm using, but USB networking doesn't seem to work with that. Do you have USB networking working with that u-boot? If so, what changes to the config did you make? Kevin > > On Thu, Oct 17, 2013 at 5:00 PM, Kevin Hilman <khilman@xxxxxxxxxx> wrote: > >> Aliaksei Katovich <aliaksei.katovich@xxxxxxxxx> writes: >> >> > hi Kevin; >> > >> >> Vyacheslav Tyrtov <v.tyrtov@xxxxxxxxxxx> writes: >> >> >> >> > The series of patches represent support of Exynos 5410 SoC >> >> > >> >> > The Exynos 5410 is the first Samsung SoC based on bigLITTLE >> architecture. >> >> > Patches allow all 8 CPU cores (4 x A7 and 4 x A15) to run at the same >> time >> >> > >> >> > Patches add new platform description, support of clock controller, >> >> > dual cluster support and device tree for Exynos 5410 >> >> > >> >> > Has been build on v3.12-rc5. >> >> > Has been tested on Exynos 5410 reference board (exynos_defconfig). >> >> >> >> Has anyone tried this on the exynos5410 based odroid-xu yet? >> >> >> >> I tried booting this on my recently arrived odroid-xu, but am not >> >> getting it to boot. >> > >> > I am able to boot my odroid-xu+e to busybox with these patches >> applied >> > against 3.12-rc5: exynos_defconfig and exynos5410-smdk5410.dtb were >> > used. >> > >> > However there seem to be some issues with virq allocations, like >> this: >> >> Ah, I've seen the same thing, but for me it doesn't boot reliably. >> Sometimes there's an immediate fault like this[1], and once in a rare >> while, it starts to boot and I see the same virq errors. >> >> Curious what you guys are using for boot loaders. I found some >> pre-build u-boot binaries along with the necessary BL1/2 binary blobs in >> the hardkernel kernel repo: https://github.com/hardkernel/linux.git >> branch: origin/odroidxu-3.4.y >> path: tools/hardkernel/u-boot-pre-built >> >> Unfortunatly, that u-boot doesn't have usb networking support built in >> so I couln't use u-boot to tftp the kernel, so I was able to use fasboot >> to load the kernel/ramdisk, but it's very flaky. >> >> Do you have an pointers of where to get a known working bootloader. >> Ideally, a u-boot with networking/tftp support would be ideal. >> >> Thanks, >> >> Kevin >> >> [1] >> USB cable Connected![0x4] >> Starting download of 10008576 bytes >> ......... >> downloading of 10008576 bytes finished >> Kernel size: 00296bc5 >> Ramdisk size: 006f3c00 >> Booting kernel.. >> ## Booting kernel from Legacy Image at 40008000 ... >> Image Name: Linux >> Image Type: ARM Linux Kernel Image (uncompressed) >> Data Size: 2714501 Bytes = 2.6 MiB >> Load Address: 40008000 >> Entry Point: 40008000 >> Verifying Checksum ... OK >> XIP Kernel Image ... OK >> OK >> >> Starting kernel ... >> >> undefined instruction >> pc : [<4000800c>] lr : [<bfc65df4>] >> sp : bfb5bbc8 ip : 00000000 fp : 00001251 >> r10: 00000000 r9 : 00000000 r8 : bfb5bf30 >> r7 : 00000000 r6 : 00000000 r5 : 40008000 r4 : bfcabac0 >> r3 : bfb5bfa8 r2 : 40000100 r1 : 00001251 r0 : 00000000 >> Flags: nZCv IRQs off FIQs off Mode SVC_32 >> Resetting CPU ... >> >> emmc resetting ... >> resetting ... >> >> -- >> To unsubscribe from this list: send the line "unsubscribe >> linux-samsung-soc" in >> the body of a message to majordomo@xxxxxxxxxxxxxxx >> More majordomo info at http://vger.kernel.org/majordomo-info.html >> -- To unsubscribe from this list: send the line "unsubscribe linux-doc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
