Quoting Vyacheslav Tyrtov (2013-10-14 08:08:23)
> From: Tarek Dakhran <t.dakhran@xxxxxxxxxxx>
>
> The EXYNOS5410 clocks are statically listed and registered
> using the Samsung specific common clock helper functions.
>
> Signed-off-by: Tarek Dakhran <t.dakhran@xxxxxxxxxxx>
> Signed-off-by: Vyacheslav Tyrtov <v.tyrtov@xxxxxxxxxxx>
Looks good to me. Any objections for me to take this through the clk
tree?
Regards,
Mike
> ---
> .../devicetree/bindings/clock/exynos5410-clock.txt | 37 +++
> drivers/clk/samsung/Makefile | 1 +
> drivers/clk/samsung/clk-exynos5410.c | 251 +++++++++++++++++++++
> include/dt-bindings/clock/exynos5410.h | 175 ++++++++++++++
> 4 files changed, 464 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/clock/exynos5410-clock.txt
> create mode 100644 drivers/clk/samsung/clk-exynos5410.c
> create mode 100644 include/dt-bindings/clock/exynos5410.h
>
> diff --git a/Documentation/devicetree/bindings/clock/exynos5410-clock.txt b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt
> new file mode 100644
> index 0000000..a462da231
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt
> @@ -0,0 +1,37 @@
> +* Samsung Exynos5410 Clock Controller
> +
> +The Exynos5410 clock controller generates and supplies clock to various
> +controllers within the Exynos5410 SoC.
> +
> +Required Properties:
> +
> +- compatible: should be "samsung,exynos5410-clock"
> +
> +- reg: physical base address of the controller and length of memory mapped
> + region.
> +
> +- #clock-cells: should be 1.
> +
> +All available clocks are defined as preprocessor macros in
> +dt-bindings/clock/exynos5410.h header and can be used in device
> +tree sources.
> +
> +Example 1: An example of a clock controller node is listed below.
> +
> + clock: clock-controller@0x10010000 {
> + compatible = "samsung,exynos5410-clock";
> + reg = <0x10010000 0x30000>;
> + #clock-cells = <1>;
> + };
> +
> +Example 2: UART controller node that consumes the clock generated by the clock
> + controller. Refer to the standard clock bindings for information
> + about 'clocks' and 'clock-names' property.
> +
> + serial@12C20000 {
> + compatible = "samsung,exynos4210-uart";
> + reg = <0x12C00000 0x100>;
> + interrupts = <0 51 0>;
> + clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
> + clock-names = "uart", "clk_uart_baud0";
> + };
> diff --git a/drivers/clk/samsung/Makefile b/drivers/clk/samsung/Makefile
> index 3413380..5a446ca 100644
> --- a/drivers/clk/samsung/Makefile
> +++ b/drivers/clk/samsung/Makefile
> @@ -5,6 +5,7 @@
> obj-$(CONFIG_COMMON_CLK) += clk.o clk-pll.o
> obj-$(CONFIG_ARCH_EXYNOS4) += clk-exynos4.o
> obj-$(CONFIG_SOC_EXYNOS5250) += clk-exynos5250.o
> +obj-$(CONFIG_SOC_EXYNOS5410) += clk-exynos5410.o
> obj-$(CONFIG_SOC_EXYNOS5420) += clk-exynos5420.o
> obj-$(CONFIG_SOC_EXYNOS5440) += clk-exynos5440.o
> obj-$(CONFIG_ARCH_EXYNOS) += clk-exynos-audss.o
> diff --git a/drivers/clk/samsung/clk-exynos5410.c b/drivers/clk/samsung/clk-exynos5410.c
> new file mode 100644
> index 0000000..c5eba08
> --- /dev/null
> +++ b/drivers/clk/samsung/clk-exynos5410.c
> @@ -0,0 +1,251 @@
> +/*
> + * Copyright (c) 2013 Samsung Electronics Co., Ltd.
> + * Author: Tarek Dakhran <t.dakhran@xxxxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * Common Clock Framework support for Exynos5410 SoC.
> +*/
> +
> +#include <dt-bindings/clock/exynos5410.h>
> +
> +#include <linux/clk.h>
> +#include <linux/clkdev.h>
> +#include <linux/clk-provider.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +
> +#include "clk.h"
> +
> +#define APLL_LOCK 0x0
> +#define APLL_CON0 0x100
> +#define CPLL_LOCK 0x10020
> +#define CPLL_CON0 0x10120
> +#define MPLL_LOCK 0x4000
> +#define MPLL_CON0 0x4100
> +#define BPLL_LOCK 0x20010
> +#define BPLL_CON0 0x20110
> +#define KPLL_LOCK 0x28000
> +#define KPLL_CON0 0x28100
> +
> +#define SRC_CPU 0x200
> +#define DIV_CPU0 0x500
> +#define SRC_CPERI1 0x4204
> +#define DIV_TOP0 0x10510
> +#define DIV_TOP1 0x10514
> +#define DIV_FSYS1 0x1054c
> +#define DIV_FSYS2 0x10550
> +#define DIV_PERIC0 0x10558
> +#define SRC_TOP0 0x10210
> +#define SRC_TOP1 0x10214
> +#define SRC_TOP2 0x10218
> +#define SRC_FSYS 0x10244
> +#define SRC_PERIC0 0x10250
> +#define SRC_MASK_FSYS 0x10340
> +#define SRC_MASK_PERIC0 0x10350
> +#define GATE_BUS_FSYS0 0x10740
> +#define GATE_IP_FSYS 0x10944
> +#define GATE_IP_PERIC 0x10950
> +#define GATE_IP_PERIS 0x10960
> +#define SRC_CDREX 0x20200
> +#define SRC_KFC 0x28200
> +#define DIV_KFC0 0x28500
> +
> +/* list of PLLs */
> +enum exynos5410_plls {
> + apll, cpll, mpll,
> + bpll, kpll,
> + nr_plls /* number of PLLs */
> +};
> +
> +/*
> + * list of controller registers to be saved and restored during a
> + * suspend/resume cycle.
> + */
> +static unsigned long exynos5410_clk_regs[] __initdata = {
> + SRC_CPU,
> + DIV_CPU0,
> + SRC_CPERI1,
> + DIV_TOP0,
> + DIV_TOP1,
> + DIV_FSYS1,
> + DIV_FSYS2,
> + DIV_PERIC0,
> + SRC_TOP0,
> + SRC_TOP1,
> + SRC_TOP2,
> + SRC_FSYS,
> + SRC_PERIC0,
> + SRC_MASK_FSYS,
> + SRC_MASK_PERIC0,
> + GATE_BUS_FSYS0,
> + GATE_IP_FSYS,
> + GATE_IP_PERIC,
> + GATE_IP_PERIS,
> + SRC_CDREX,
> + SRC_KFC,
> + DIV_KFC0,
> +};
> +
> +/* list of all parent clocks */
> +PNAME(apll_p) = { "fin_pll", "fout_apll", };
> +PNAME(bpll_p) = { "fin_pll", "fout_bpll", };
> +PNAME(cpll_p) = { "fin_pll", "fout_cpll" };
> +PNAME(mpll_p) = { "fin_pll", "fout_mpll", };
> +PNAME(kpll_p) = { "fin_pll", "fout_kpll", };
> +
> +PNAME(mout_cpu_p) = { "mout_apll", "sclk_mpll", };
> +PNAME(mout_kfc_p) = { "mout_kpll", "sclk_mpll", };
> +
> +PNAME(mpll_user_p) = { "fin_pll", "sclk_mpll", };
> +PNAME(bpll_user_p) = { "fin_pll", "sclk_bpll", };
> +PNAME(mpll_bpll_p) = { "sclk_mpll_muxed", "sclk_bpll_muxed", };
> +
> +PNAME(group2_p) = { "fin_pll", "fin_pll", "none", "none",
> + "none", "none", "sclk_mpll_bpll",
> + "none", "none", "sclk_cpll" };
> +
> +/* fixed rate clocks generated outside the soc */
> +static struct samsung_fixed_rate_clock exynos5410_frt_ext_clks[] __initdata = {
> + FRATE(CLK_FIN_PLL, "fin_pll", NULL, CLK_IS_ROOT, 0),
> +};
> +
> +static struct samsung_mux_clock exynos5410_mux_clks[] __initdata = {
> + MUX(0, "mout_apll", apll_p, SRC_CPU, 0, 1),
> + MUX(0, "mout_cpu", mout_cpu_p, SRC_CPU, 16, 1),
> +
> + MUX(0, "mout_kpll", kpll_p, SRC_KFC, 0, 1),
> + MUX(0, "mout_kfc", mout_kfc_p, SRC_KFC, 16, 1),
> +
> + MUX(0, "sclk_mpll", mpll_p, SRC_CPERI1, 8, 1),
> + MUX(0, "sclk_mpll_muxed", mpll_user_p, SRC_TOP2, 20, 1),
> +
> + MUX(0, "sclk_bpll", bpll_p, SRC_CDREX, 0, 1),
> + MUX(0, "sclk_bpll_muxed", bpll_user_p, SRC_TOP2, 24, 1),
> +
> + MUX(0, "sclk_cpll", cpll_p, SRC_TOP2, 8, 1),
> +
> + MUX(0, "sclk_mpll_bpll", mpll_bpll_p, SRC_TOP1, 20, 1),
> +
> + MUX(0, "mout_mmc0", group2_p, SRC_FSYS, 0, 4),
> + MUX(0, "mout_mmc1", group2_p, SRC_FSYS, 4, 4),
> + MUX(0, "mout_mmc2", group2_p, SRC_FSYS, 8, 4),
> +
> + MUX(0, "mout_uart0", group2_p, SRC_PERIC0, 0, 4),
> + MUX(0, "mout_uart1", group2_p, SRC_PERIC0, 4, 4),
> + MUX(0, "mout_uart2", group2_p, SRC_PERIC0, 8, 4),
> +
> + MUX(0, "mout_aclk200", mpll_bpll_p, SRC_TOP0, 12, 1),
> + MUX(0, "mout_aclk400", mpll_bpll_p, SRC_TOP0, 20, 1),
> +};
> +
> +static struct samsung_div_clock exynos5410_div_clks[] __initdata = {
> + DIV(0, "div_arm", "mout_cpu", DIV_CPU0, 0, 3),
> + DIV(0, "div_arm2", "div_arm", DIV_CPU0, 28, 3),
> +
> + DIV(0, "div_acp", "div_arm2", DIV_CPU0, 8, 3),
> + DIV(0, "div_cpud", "div_arm2", DIV_CPU0, 4, 3),
> + DIV(0, "div_atb", "div_arm2", DIV_CPU0, 16, 3),
> + DIV(0, "pclk_dbg", "div_arm2", DIV_CPU0, 20, 3),
> +
> + DIV(0, "div_kfc", "mout_kfc", DIV_KFC0, 0, 3),
> + DIV(0, "div_aclk", "div_kfc", DIV_KFC0, 4, 3),
> + DIV(0, "div_pclk", "div_kfc", DIV_KFC0, 20, 3),
> +
> + DIV(0, "aclk66_pre", "sclk_mpll_muxed", DIV_TOP1, 24, 3),
> + DIV(0, "aclk66", "aclk66_pre", DIV_TOP0, 0, 3),
> +
> + DIV(0, "div_mmc0", "mout_mmc0", DIV_FSYS1, 0, 4),
> + DIV(0, "div_mmc1", "mout_mmc1", DIV_FSYS1, 16, 4),
> + DIV(0, "div_mmc2", "mout_mmc2", DIV_FSYS2, 0, 4),
> +
> + DIV_F(0, "div_mmc_pre0", "div_mmc0",
> + DIV_FSYS1, 8, 8, CLK_SET_RATE_PARENT, 0),
> + DIV_F(0, "div_mmc_pre1", "div_mmc1",
> + DIV_FSYS1, 24, 8, CLK_SET_RATE_PARENT, 0),
> + DIV_F(0, "div_mmc_pre2", "div_mmc2",
> + DIV_FSYS2, 8, 8, CLK_SET_RATE_PARENT, 0),
> +
> + DIV(0, "div_uart0", "mout_uart0", DIV_PERIC0, 0, 4),
> + DIV(0, "div_uart1", "mout_uart1", DIV_PERIC0, 4, 4),
> + DIV(0, "div_uart2", "mout_uart2", DIV_PERIC0, 8, 4),
> + DIV(0, "div_uart3", "mout_uart3", DIV_PERIC0, 12, 4),
> +
> + DIV(0, "aclk200", "mout_aclk200", DIV_TOP0, 12, 3),
> + DIV(0, "aclk400", "mout_aclk400", DIV_TOP0, 24, 3),
> +};
> +
> +static struct samsung_gate_clock exynos5410_gate_clks[] __initdata = {
> + GATE(CLK_MCT, "mct", "aclk66", GATE_IP_PERIS, 18, 0, 0),
> +
> + GATE(CLK_SCLK_MMC0, "sclk_mmc0", "div_mmc_pre0",
> + SRC_MASK_FSYS, 0, CLK_SET_RATE_PARENT, 0),
> + GATE(CLK_SCLK_MMC1, "sclk_mmc1", "div_mmc_pre1",
> + SRC_MASK_FSYS, 4, CLK_SET_RATE_PARENT, 0),
> + GATE(CLK_SCLK_MMC2, "sclk_mmc2", "div_mmc_pre2",
> + SRC_MASK_FSYS, 8, CLK_SET_RATE_PARENT, 0),
> +
> + GATE(CLK_MMC0, "sdmmc0", "aclk200", GATE_BUS_FSYS0, 12, 0, 0),
> + GATE(CLK_MMC1, "sdmmc1", "aclk200", GATE_BUS_FSYS0, 13, 0, 0),
> + GATE(CLK_MMC2, "sdmmc2", "aclk200", GATE_BUS_FSYS0, 14, 0, 0),
> +
> + GATE(CLK_UART0, "uart0", "aclk66", GATE_IP_PERIC, 0, 0, 0),
> + GATE(CLK_UART1, "uart1", "aclk66", GATE_IP_PERIC, 1, 0, 0),
> + GATE(CLK_UART2, "uart2", "aclk66", GATE_IP_PERIC, 2, 0, 0),
> +
> + GATE(CLK_SCLK_UART0, "sclk_uart0", "div_uart0",
> + SRC_MASK_PERIC0, 0, CLK_SET_RATE_PARENT, 0),
> + GATE(CLK_SCLK_UART1, "sclk_uart1", "div_uart1",
> + SRC_MASK_PERIC0, 4, CLK_SET_RATE_PARENT, 0),
> + GATE(CLK_SCLK_UART2, "sclk_uart2", "div_uart2",
> + SRC_MASK_PERIC0, 8, CLK_SET_RATE_PARENT, 0),
> +};
> +
> +static struct samsung_pll_clock exynos5410_plls[nr_plls] __initdata = {
> + [apll] = PLL(pll_35xx, CLK_FOUT_APLL, "fout_apll", "fin_pll", APLL_LOCK,
> + APLL_CON0, NULL),
> + [cpll] = PLL(pll_35xx, CLK_FOUT_CPLL, "fout_cpll", "fin_pll", CPLL_LOCK,
> + CPLL_CON0, NULL),
> + [mpll] = PLL(pll_35xx, CLK_FOUT_MPLL, "fout_mpll", "fin_pll", MPLL_LOCK,
> + MPLL_CON0, NULL),
> + [bpll] = PLL(pll_35xx, CLK_FOUT_BPLL, "fout_bpll", "fin_pll", BPLL_LOCK,
> + BPLL_CON0, NULL),
> + [kpll] = PLL(pll_35xx, CLK_FOUT_KPLL, "fout_kpll", "fin_pll", KPLL_LOCK,
> + KPLL_CON0, NULL),
> +};
> +
> +static struct of_device_id ext_clk_match[] __initdata = {
> + { .compatible = "samsung,clock-oscclk", .data = (void *)0, },
> + { },
> +};
> +
> +/* register exynos5410 clocks */
> +static void __init exynos5410_clk_init(struct device_node *np)
> +{
> + void __iomem *reg_base;
> +
> + reg_base = of_iomap(np, 0);
> + if (!reg_base)
> + panic("%s: failed to map registers\n", __func__);
> +
> + samsung_clk_init(np, reg_base, CLK_NR_CLKS,
> + exynos5410_clk_regs, ARRAY_SIZE(exynos5410_clk_regs),
> + NULL, 0);
> + samsung_clk_of_register_fixed_ext(exynos5410_frt_ext_clks,
> + ARRAY_SIZE(exynos5410_frt_ext_clks),
> + ext_clk_match);
> + samsung_clk_register_pll(exynos5410_plls, ARRAY_SIZE(exynos5410_plls),
> + reg_base);
> +
> + samsung_clk_register_mux(exynos5410_mux_clks,
> + ARRAY_SIZE(exynos5410_mux_clks));
> + samsung_clk_register_div(exynos5410_div_clks,
> + ARRAY_SIZE(exynos5410_div_clks));
> + samsung_clk_register_gate(exynos5410_gate_clks,
> + ARRAY_SIZE(exynos5410_gate_clks));
> +
> + pr_debug("Exynos5410: clock setup completed.\n");
> +}
> +CLK_OF_DECLARE(exynos5410_clk, "samsung,exynos5410-clock", exynos5410_clk_init);
> diff --git a/include/dt-bindings/clock/exynos5410.h b/include/dt-bindings/clock/exynos5410.h
> new file mode 100644
> index 0000000..9b4a58b
> --- /dev/null
> +++ b/include/dt-bindings/clock/exynos5410.h
> @@ -0,0 +1,175 @@
> +#ifndef _DT_BINDINGS_CLOCK_EXYNOS_5410_H
> +#define _DT_BINDINGS_CLOCK_EXYNOS_5410_H
> +
> +/* core clocks */
> +#define CLK_FIN_PLL 1
> +#define CLK_FOUT_APLL 2
> +#define CLK_FOUT_CPLL 3
> +#define CLK_FOUT_DPLL 4
> +#define CLK_FOUT_EPLL 5
> +#define CLK_FOUT_RPLL 6
> +#define CLK_FOUT_IPLL 7
> +#define CLK_FOUT_SPLL 8
> +#define CLK_FOUT_VPLL 9
> +#define CLK_FOUT_MPLL 10
> +#define CLK_FOUT_BPLL 11
> +#define CLK_FOUT_KPLL 12
> +
> +/* gate for special clocks (sclk) */
> +#define CLK_SCLK_UART0 128
> +#define CLK_SCLK_UART1 129
> +#define CLK_SCLK_UART2 130
> +#define CLK_SCLK_UART3 131
> +#define CLK_SCLK_MMC0 132
> +#define CLK_SCLK_MMC1 133
> +#define CLK_SCLK_MMC2 134
> +#define CLK_SCLK_SPI0 135
> +#define CLK_SCLK_SPI1 136
> +#define CLK_SCLK_SPI2 137
> +#define CLK_SCLK_I2S1 138
> +#define CLK_SCLK_I2S2 139
> +#define CLK_SCLK_PCM1 140
> +#define CLK_SCLK_PCM2 141
> +#define CLK_SCLK_SPDIF 142
> +#define CLK_SCLK_HDMI 143
> +#define CLK_SCLK_PIXEL 144
> +#define CLK_SCLK_DP1 145
> +#define CLK_SCLK_MIPI1 146
> +#define CLK_SCLK_FIMD1 147
> +#define CLK_SCLK_MAUDIO0 148
> +#define CLK_SCLK_MAUPCM0 149
> +#define CLK_SCLK_USBD300 150
> +#define CLK_SCLK_USBD301 151
> +#define CLK_SCLK_USBPHY300 152
> +#define CLK_SCLK_USBPHY301 153
> +#define CLK_SCLK_UNIPRO 154
> +#define CLK_SCLK_PWM 155
> +#define CLK_SCLK_GSCL_WA 156
> +#define CLK_SCLK_GSCL_WB 157
> +#define CLK_SCLK_HDMIPHY 158
> +
> +/* gate clocks */
> +#define CLK_ACLK66_PERIC 256
> +#define CLK_UART0 257
> +#define CLK_UART1 258
> +#define CLK_UART2 259
> +#define CLK_UART3 260
> +#define CLK_I2C0 261
> +#define CLK_I2C1 262
> +#define CLK_I2C2 263
> +#define CLK_I2C3 264
> +#define CLK_I2C4 265
> +#define CLK_I2C5 266
> +#define CLK_I2C6 267
> +#define CLK_I2C7 268
> +#define CLK_I2C_HDMI 269
> +#define CLK_TSADC 270
> +#define CLK_SPI0 271
> +#define CLK_SPI1 272
> +#define CLK_SPI2 273
> +#define CLK_KEYIF 274
> +#define CLK_I2S1 275
> +#define CLK_I2S2 276
> +#define CLK_PCM1 277
> +#define CLK_PCM2 278
> +#define CLK_PWM 279
> +#define CLK_SPDIF 280
> +#define CLK_I2C8 281
> +#define CLK_I2C9 282
> +#define CLK_I2C10 283
> +#define CLK_ACLK66_PSGEN 300
> +#define CLK_CHIPID 301
> +#define CLK_SYSREG 302
> +#define CLK_TZPC0 303
> +#define CLK_TZPC1 304
> +#define CLK_TZPC2 305
> +#define CLK_TZPC3 306
> +#define CLK_TZPC4 307
> +#define CLK_TZPC5 308
> +#define CLK_TZPC6 309
> +#define CLK_TZPC7 310
> +#define CLK_TZPC8 311
> +#define CLK_TZPC9 312
> +#define CLK_HDMI_CEC 313
> +#define CLK_SECKEY 314
> +#define CLK_MCT 315
> +#define CLK_WDT 316
> +#define CLK_RTC 317
> +#define CLK_TMU 318
> +#define CLK_TMU_GPU 319
> +#define CLK_PCLK66_GPIO 330
> +#define CLK_ACLK200_FSYS2 350
> +#define CLK_MMC0 351
> +#define CLK_MMC1 352
> +#define CLK_MMC2 353
> +#define CLK_SROMC 354
> +#define CLK_UFS 355
> +#define CLK_ACLK200_FSYS 360
> +#define CLK_TSI 361
> +#define CLK_PDMA0 362
> +#define CLK_PDMA1 363
> +#define CLK_RTIC 364
> +#define CLK_USBH20 365
> +#define CLK_USBD300 366
> +#define CLK_USBD301 367
> +#define CLK_ACLK400_MSCL 380
> +#define CLK_MSCL0 381
> +#define CLK_MSCL1 382
> +#define CLK_MSCL2 383
> +#define CLK_SMMU_MSCL0 384
> +#define CLK_SMMU_MSCL1 385
> +#define CLK_SMMU_MSCL2 386
> +#define CLK_ACLK333 400
> +#define CLK_MFC 401
> +#define CLK_SMMU_MFCL 402
> +#define CLK_SMMU_MFCR 403
> +#define CLK_ACLK200_DISP1 410
> +#define CLK_DSIM1 411
> +#define CLK_DP1 412
> +#define CLK_HDMI 413
> +#define CLK_ACLK300_DISP1 420
> +#define CLK_FIMD1 421
> +#define CLK_SMMU_FIMD1 422
> +#define CLK_ACLK166 430
> +#define CLK_MIXER 431
> +#define CLK_ACLK266 440
> +#define CLK_ROTATOR 441
> +#define CLK_MDMA1 442
> +#define CLK_SMMU_ROTATOR 443
> +#define CLK_SMMU_MDMA1 444
> +#define CLK_ACLK300_JPEG 450
> +#define CLK_JPEG 451
> +#define CLK_JPEG2 452
> +#define CLK_SMMU_JPEG 453
> +#define CLK_ACLK300_GSCL 460
> +#define CLK_SMMU_GSCL0 461
> +#define CLK_SMMU_GSCL1 462
> +#define CLK_GSCL_WA 463
> +#define CLK_GSCL_WB 464
> +#define CLK_GSCL0 465
> +#define CLK_GSCL1 466
> +#define CLK_CLK_3AA 467
> +#define CLK_ACLK266_G2D 470
> +#define CLK_SSS 471
> +#define CLK_SLIM_SSS 472
> +#define CLK_MDMA0 473
> +#define CLK_ACLK333_G2D 480
> +#define CLK_G2D 481
> +#define CLK_ACLK333_432_GSCL 490
> +#define CLK_SMMU_3AA 491
> +#define CLK_SMMU_FIMCL0 492
> +#define CLK_SMMU_FIMCL1 493
> +#define CLK_SMMU_FIMCL3 494
> +#define CLK_FIMC_LITE3 495
> +#define CLK_ACLK_G3D 500
> +#define CLK_G3D 501
> +#define CLK_SMMU_MIXER 502
> +
> +/* mux clocks */
> +#define CLK_MOUT_HDMI 640
> +
> +/* divider clocks */
> +#define CLK_DOUT_PIXEL 768
> +#define CLK_NR_CLKS 769
> +
> +#endif /* _DT_BINDINGS_CLOCK_EXYNOS_5410_H */
> --
> 1.8.1.5
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
