Add notify_suspend and notify_resume according to different SoCs.
Signed-off-by: Peter Chen <peter.chen@xxxxxxxxxxxxx>
---
drivers/usb/phy/phy-mxs-usb.c | 91 +++++++++++++++++++++++++++++++++++++++--
1 files changed, 87 insertions(+), 4 deletions(-)
diff --git a/drivers/usb/phy/phy-mxs-usb.c b/drivers/usb/phy/phy-mxs-usb.c
index 6d48bde..4416ed6 100644
--- a/drivers/usb/phy/phy-mxs-usb.c
+++ b/drivers/usb/phy/phy-mxs-usb.c
@@ -164,8 +164,8 @@ static int mxs_phy_suspend(struct usb_phy *x, int suspend)
static int mxs_phy_on_connect(struct usb_phy *phy,
enum usb_device_speed speed)
{
- dev_dbg(phy->dev, "%s speed device has connected\n",
- (speed == USB_SPEED_HIGH) ? "high" : "non-high");
+ dev_dbg(phy->dev, "%s device has connected\n",
+ (speed == USB_SPEED_HIGH) ? "HS" : "FS/LS");
if (speed == USB_SPEED_HIGH)
writel(BM_USBPHY_CTRL_ENHOSTDISCONDETECT,
@@ -177,8 +177,8 @@ static int mxs_phy_on_connect(struct usb_phy *phy,
static int mxs_phy_on_disconnect(struct usb_phy *phy,
enum usb_device_speed speed)
{
- dev_dbg(phy->dev, "%s speed device has disconnected\n",
- (speed == USB_SPEED_HIGH) ? "high" : "non-high");
+ dev_dbg(phy->dev, "%s device has disconnected\n",
+ (speed == USB_SPEED_HIGH) ? "HS" : "FS/LS");
if (speed == USB_SPEED_HIGH)
writel(BM_USBPHY_CTRL_ENHOSTDISCONDETECT,
@@ -187,6 +187,88 @@ static int mxs_phy_on_disconnect(struct usb_phy *phy,
return 0;
}
+static int mxs_phy_on_suspend_workaround(struct usb_phy *phy,
+ enum usb_device_speed speed)
+{
+ dev_dbg(phy->dev, "%s device has suspended\n",
+ (speed == USB_SPEED_HIGH) ? "HS" : "FS/LS");
+
+ /* delay 4ms to wait bus entering idle */
+ usleep_range(4000, 5000);
+
+ /*
+ * Workaround for wakeup signal between portsc.suspendM
+ * and PHY enters low power mode.
+ */
+ writel_relaxed(0xffffffff, phy->io_priv + HW_USBPHY_PWD);
+ writel_relaxed(0, phy->io_priv + HW_USBPHY_PWD);
+
+ if (speed == USB_SPEED_HIGH)
+ writel_relaxed(BM_USBPHY_CTRL_ENHOSTDISCONDETECT,
+ phy->io_priv + HW_USBPHY_CTRL_CLR);
+
+ return 0;
+}
+
+static int mxs_phy_on_suspend(struct usb_phy *phy,
+ enum usb_device_speed speed)
+{
+ dev_dbg(phy->dev, "%s device has suspended\n",
+ (speed == USB_SPEED_HIGH) ? "HS" : "FS/LS");
+
+ /* delay 4ms to wait bus entering idle */
+ usleep_range(4000, 5000);
+
+ if (speed == USB_SPEED_HIGH)
+ writel_relaxed(BM_USBPHY_CTRL_ENHOSTDISCONDETECT,
+ phy->io_priv + HW_USBPHY_CTRL_CLR);
+
+ return 0;
+}
+
+/*
+ * The resume signal must be finished here.
+ */
+static int mxs_phy_on_resume(struct usb_phy *phy,
+ enum usb_device_speed speed)
+{
+ dev_dbg(phy->dev, "%s device has resumed\n",
+ (speed == USB_SPEED_HIGH) ? "HS" : "FS/LS");
+
+ if (speed == USB_SPEED_HIGH) {
+ /* Make sure the device has switched to High-Speed mode */
+ udelay(500);
+ writel_relaxed(BM_USBPHY_CTRL_ENHOSTDISCONDETECT,
+ phy->io_priv + HW_USBPHY_CTRL_SET);
+ }
+
+ return 0;
+}
+
+/*
+ * For mxs PHY, there are two PHY issues related to suspend/resume.
+ *
+ * 1. The PHY will be in messy if there is an wakeup after putting
+ * bus to suspend (set portsc.suspendM) but before setting PHY to low
+ * power mode (set portsc.phcd).
+ * 2. The SOF sends too fast after resuming, it will cause disconnection
+ * between host and high speed device.
+ *
+ * For mx23 and mx28, both of two issues are existed.
+ * For mx6q and mx6dl, only the second issue is existed.
+ * For mx6 sololite and later SoCs, none issue is existed.
+ */
+static void mxs_phy_workaround(struct mxs_phy *mxs_phy)
+{
+ if (is_mx23_phy(mxs_phy)) {
+ mxs_phy->phy.notify_suspend = mxs_phy_on_suspend_workaround;
+ mxs_phy->phy.notify_resume = mxs_phy_on_resume;
+ } else if (is_mx6q_phy(mxs_phy)) {
+ mxs_phy->phy.notify_suspend = mxs_phy_on_suspend;
+ mxs_phy->phy.notify_resume = mxs_phy_on_resume;
+ }
+}
+
static int mxs_phy_probe(struct platform_device *pdev)
{
struct resource *res;
@@ -247,6 +329,7 @@ static int mxs_phy_probe(struct platform_device *pdev)
mxs_phy->clk = clk;
mxs_phy->devtype = pdev->id_entry->driver_data;
+ mxs_phy_workaround(mxs_phy);
platform_set_drvdata(pdev, &mxs_phy->phy);
--
1.7.1
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
