> Driver for Renesas ISL28022 power monitor with I2C interface.
> The device monitors voltage, current via shunt resistor and calculated power.
>
> Signed-off-by: Carsten Spieß <mail@xxxxxxxxxxxxxxxxx>
Hi Carsten,
We added support for reading shunt voltage in mV and revise code by some comment from maintainer.
Would you might take a look into it and apply to the patch set? Thank you.
Best Regards,
Delphine CC Chiu
---
drivers/hwmon/isl28022.c | 88 ++++++++++++++++++++++++++++------------
1 file changed, 63 insertions(+), 25 deletions(-)
diff --git a/drivers/hwmon/isl28022.c b/drivers/hwmon/isl28022.c
index f0494c3bd483..c5bcefc96256 100644
--- a/drivers/hwmon/isl28022.c
+++ b/drivers/hwmon/isl28022.c
@@ -85,8 +85,6 @@ struct isl28022_data {
u32 shunt;
u32 gain;
u32 average;
- u16 config;
- u16 calib;
};
static int isl28022_read(struct device *dev, enum hwmon_sensor_types type,
@@ -95,20 +93,61 @@ static int isl28022_read(struct device *dev, enum hwmon_sensor_types type,
struct isl28022_data *data = dev_get_drvdata(dev);
unsigned int regval;
int err;
+ u16 sign_bit;
switch (type) {
case hwmon_in:
- switch (attr) {
- case hwmon_in_input:
- err = regmap_read(data->regmap,
- ISL28022_REG_BUS, ®val);
- if (err < 0)
- return err;
- /* driver supports only 60V mode (BRNG 11) */
- *val = (long)(((u16)regval) & 0xFFFC);
+ switch (channel) {
+ case 0:
+ switch (attr) {
+ case hwmon_in_input:
+ err = regmap_read(data->regmap,
+ ISL28022_REG_BUS, ®val);
+ if (err < 0)
+ return err;
+ /* driver supports only 60V mode (BRNG 11) */
+ *val = (long)(((u16)regval) & 0xFFFC);
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
+ break;
+ case 1:
+ switch (attr) {
+ case hwmon_in_input:
+ err = regmap_read(data->regmap,
+ ISL28022_REG_SHUNT, ®val);
+ if (err < 0)
+ return err;
+ switch (data->gain) {
+ case 8:
+ sign_bit = (regval >> 15) & 0x01;
+ *val = (long)((((u16)regval) & 0x7FFF) -
+ (sign_bit * 32768)) / 100;
+ break;
+ case 4:
+ sign_bit = (regval >> 14) & 0x01;
+ *val = (long)((((u16)regval) & 0x3FFF) -
+ (sign_bit * 16384)) / 100;
+ break;
+ case 2:
+ sign_bit = (regval >> 13) & 0x01;
+ *val = (long)((((u16)regval) & 0x1FFF) -
+ (sign_bit * 8192)) / 100;
+ break;
+ case 1:
+ sign_bit = (regval >> 12) & 0x01;
+ *val = (long)((((u16)regval) & 0x0FFF) -
+ (sign_bit * 4096)) / 100;
+ break;
+ }
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
break;
default:
- return -EINVAL;
+ return -EOPNOTSUPP;
}
break;
case hwmon_curr:
@@ -122,7 +161,7 @@ static int isl28022_read(struct device *dev, enum hwmon_sensor_types type,
(long)data->shunt;
break;
default:
- return -EINVAL;
+ return -EOPNOTSUPP;
}
break;
case hwmon_power:
@@ -136,11 +175,11 @@ static int isl28022_read(struct device *dev, enum hwmon_sensor_types type,
(long)data->shunt) * (long)regval;
break;
default:
- return -EINVAL;
+ return -EOPNOTSUPP;
}
break;
default:
- return -EINVAL;
+ return -EOPNOTSUPP;
}
return 0;
@@ -182,7 +221,8 @@ static umode_t isl28022_is_visible(const void *data, enum hwmon_sensor_types typ
static const struct hwmon_channel_info *isl28022_info[] = {
HWMON_CHANNEL_INFO(in,
- HWMON_I_INPUT), /* channel 0: bus voltage (mV) */
+ HWMON_I_INPUT, /* channel 0: bus voltage (mV) */
+ HWMON_I_INPUT), /* channel 1: shunt voltage (mV) */
HWMON_CHANNEL_INFO(curr,
HWMON_C_INPUT), /* channel 1: current (mA) */
HWMON_CHANNEL_INFO(power,
@@ -368,24 +408,22 @@ static int isl28022_read_properties(struct device *dev, struct isl28022_data *da
static int isl28022_config(struct isl28022_data *data)
{
int err;
+ u16 config;
+ u16 calib;
- data->config = (ISL28022_MODE_CONT_SB << ISL28022_MODE_SHIFT) |
+ config = (ISL28022_MODE_CONT_SB << ISL28022_MODE_SHIFT) |
(ISL28022_BRNG_60 << ISL28022_BRNG_SHIFT) |
(__ffs(data->gain) << ISL28022_PG_SHIFT) |
((ISL28022_ADC_15_1 + __ffs(data->average)) << ISL28022_SADC_SHIFT) |
((ISL28022_ADC_15_1 + __ffs(data->average)) << ISL28022_BADC_SHIFT);
- data->calib = data->shunt ? 0x8000 / data->gain : 0;
+ calib = data->shunt ? 0x8000 / data->gain : 0;
- err = regmap_write(data->regmap, ISL28022_REG_CONFIG, data->config);
+ err = regmap_write(data->regmap, ISL28022_REG_CONFIG, config);
if (err < 0)
return err;
- err = regmap_write(data->regmap, ISL28022_REG_CALIB, data->calib);
- if (err < 0)
- return err;
-
- return 0;
+ return regmap_write(data->regmap, ISL28022_REG_CALIB, calib);;
}
static int isl28022_probe(struct i2c_client *client)
@@ -418,7 +456,7 @@ static int isl28022_probe(struct i2c_client *client)
isl28022_debugfs_init(client, data);
- hwmon_dev = devm_hwmon_device_register_with_info(dev, "isl28022_hwmon",
+ hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name,
data, &isl28022_chip_info, NULL);
if (IS_ERR(hwmon_dev))
return PTR_ERR(hwmon_dev);
@@ -438,7 +476,7 @@ static struct i2c_driver isl28022_driver = {
.driver = {
.name = "isl28022",
},
- .probe_new = isl28022_probe,
+ .probe = isl28022_probe,
.id_table = isl28022_ids,
};
--
2.25.1
