Re: [RFC PATCH 04/11] i2c: dt-bindings: configuration settings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 07/05/2024 00:51, Krishna Yarlagadda wrote:
> I2C interface timing registers are configured using config setting
> framework. Document available properties for Tegra I2C controllers.
> 
> Signed-off-by: Krishna Yarlagadda <kyarlagadda@xxxxxxxxxx>
> ---
>  .../bindings/i2c/nvidia,tegra20-i2c.yaml      | 104 ++++++++++++++++++
>  1 file changed, 104 insertions(+)
> 

You called it RFC, so not ready for review, thus just few remarks.

Please use subject prefixes matching the subsystem. You can get them for
example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
your patch is touching. For bindings, the preferred subjects are
explained here:
https://www.kernel.org/doc/html/latest/devicetree/bindings/submitting-patches.html#i-for-patch-submitters


> diff --git a/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.yaml b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.yaml
> index 424a4fc218b6..3b22e75e5aa0 100644
> --- a/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.yaml
> +++ b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.yaml
> @@ -119,6 +119,96 @@ properties:
>        - const: rx
>        - const: tx
>  
> +  config:
> +    description: Config settings for I2C devices enlisted with I2C controller.
> +      Config setting is the configuration based on chip/board/system
> +      characterization on interface/controller settings. This is needed for
> +      - making the controller internal configuration to better perform
> +      - making the interface to work proper by setting drive strength, slew
> +        rates etc
> +      - making the low power leakage.
> +      There are two types of recommended configuration settings
> +      - Controller register specific for internal operation of controller.
> +      - Pad control/Pinmux/pincontrol registers for interfacing.
> +      These configurations can further be categorized as static and dynamic.
> +      - Static config does not change until a controller is reset.
> +      - Dynamic config changes based on mode or condition, controller is
> +        operating in.
> +      I2C has configuration based on clock speed and has below modes.
> +      - common is set on all speeds and can be overridden by speed mode.
> +      - high is set when clock mode is high speed.
> +      - fastplus is set when clock mode is fast plus.
> +      - fast is set when clock mode is fast mode.
> +      - standard is set when clock mode is standard mode.
> +    $ref: /schemas/misc/nvidia,tegra-config-settings.yaml
> +    unevaluatedProperties: false
> +    properties:
> +      nvidia,i2c-clk-divisor-hs-mode:
> +        description: I2C clock divisor for HS mode.

So you decided to implement clocks in DT? No.

> +        $ref: /schemas/types.yaml#/definitions/uint32
> +        minimum: 0
> +        maximum: 0xffff

Anyway divisors, clock rates and everything is human-readable so in
decimal, not hex.

There are also several issues further, like using wrong units (time has
a unit), but since this is RFC, I will just NAK.

Best regards,
Krzysztof





[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux