[PATCH 2/2] hwmon: (nzxt-kraken3) Add support for NZXT Kraken 2023 (standard and Elite) models

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add support for NZXT Kraken 2023 (standard) and NZXT Kraken 2023 Elite
all-in-one CPU coolers. These models communicate identically to the NZXT
Kraken Z-series (Z53 code paths) in all cases except when writing the
fan curve, where setting additional bits in the report is needed.

Reviewed-by: Jonas Malaco <jonas@xxxxxxxxxxxx>
Signed-off-by: Aleksa Savic <savicaleksa83@xxxxxxxxx>
---
 Documentation/hwmon/nzxt-kraken3.rst | 19 ++++++++------
 drivers/hwmon/nzxt-kraken3.c         | 38 ++++++++++++++++++++++------
 2 files changed, 41 insertions(+), 16 deletions(-)

diff --git a/Documentation/hwmon/nzxt-kraken3.rst b/Documentation/hwmon/nzxt-kraken3.rst
index 90fd9dec15ff..57fe99d23301 100644
--- a/Documentation/hwmon/nzxt-kraken3.rst
+++ b/Documentation/hwmon/nzxt-kraken3.rst
@@ -11,17 +11,20 @@ Supported devices:
 * NZXT Kraken Z53
 * NZXT Kraken Z63
 * NZXT Kraken Z73
+* NZXT Kraken 2023
+* NZXT Kraken 2023 Elite
 
 Author: Jonas Malaco, Aleksa Savic
 
 Description
 -----------
 
-This driver enables hardware monitoring support for NZXT Kraken X53/X63/X73 and
-Z53/Z63/Z73 all-in-one CPU liquid coolers. All models expose liquid temperature
-and pump speed (in RPM), as well as PWM control (either as a fixed value
-or through a temp-PWM curve). The Z-series models additionally expose the speed
-and duty of an optionally connected fan, with the same PWM control capabilities.
+This driver enables hardware monitoring support for NZXT Kraken X53/X63/X73,
+Z53/Z63/Z73 and Kraken 2023 (standard and Elite) all-in-one CPU liquid coolers.
+All models expose liquid temperature and pump speed (in RPM), as well as PWM
+control (either as a fixed value or through a temp-PWM curve). The Z-series and
+Kraken 2023 models additionally expose the speed and duty of an optionally connected
+fan, with the same PWM control capabilities.
 
 Pump and fan duty control mode can be set through pwm[1-2]_enable, where 1 is
 for the manual control mode and 2 is for the liquid temp to PWM curve mode.
@@ -39,9 +42,9 @@ The devices can report if they are faulty. The driver supports that situation
 and will issue a warning. This can also happen when the USB cable is connected,
 but SATA power is not.
 
-The addressable RGB LEDs and LCD screen (only on Z-series models) are not
-supported in this driver, but can be controlled through existing userspace tools,
-such as `liquidctl`_.
+The addressable RGB LEDs and LCD screen (only on Z-series and Kraken 2023 models)
+are not supported in this driver, but can be controlled through existing userspace
+tools, such as `liquidctl`_.
 
 .. _liquidctl: https://github.com/liquidctl/liquidctl
 
diff --git a/drivers/hwmon/nzxt-kraken3.c b/drivers/hwmon/nzxt-kraken3.c
index 571087e3fd3e..0b3f04c740b0 100644
--- a/drivers/hwmon/nzxt-kraken3.c
+++ b/drivers/hwmon/nzxt-kraken3.c
@@ -1,8 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
- * hwmon driver for NZXT Kraken X53/X63/X73 and Z53/Z63/Z73 all in one coolers.
- * X53 and Z53 in code refer to all models in their respective series (shortened
- * for brevity).
+ * hwmon driver for NZXT Kraken X53/X63/X73, Z53/Z63/Z73 and 2023/2023 Elite all in one coolers.
+ * X53 and Z53 in code refer to all models in their respective series (shortened for brevity).
+ * 2023 models use the Z53 code paths.
  *
  * Copyright 2021  Jonas Malaco <jonas@xxxxxxxxxxxx>
  * Copyright 2022  Aleksa Savic <savicaleksa83@xxxxxxxxx>
@@ -23,8 +23,10 @@
 #define USB_PRODUCT_ID_X53		0x2007
 #define USB_PRODUCT_ID_X53_SECOND	0x2014
 #define USB_PRODUCT_ID_Z53		0x3008
+#define USB_PRODUCT_ID_KRAKEN2023	0x300E
+#define USB_PRODUCT_ID_KRAKEN2023_ELITE	0x300C
 
-enum kinds { X53, Z53 } __packed;
+enum kinds { X53, Z53, KRAKEN2023 } __packed;
 enum pwm_enable { off, manual, curve } __packed;
 
 #define DRIVER_NAME		"nzxt_kraken3"
@@ -136,6 +138,7 @@ static umode_t kraken3_is_visible(const void *data, enum hwmon_sensor_types type
 				return 0444;
 			break;
 		case Z53:
+		case KRAKEN2023:
 			/* Pump and fan */
 			if (channel < 2)
 				return 0444;
@@ -155,6 +158,7 @@ static umode_t kraken3_is_visible(const void *data, enum hwmon_sensor_types type
 					return 0644;
 				break;
 			case Z53:
+			case KRAKEN2023:
 				/* Pump and fan */
 				if (channel < 2)
 					return 0644;
@@ -242,6 +246,7 @@ static int kraken3_read_x53(struct kraken3_data *priv)
 	return 0;
 }
 
+/* Covers Z53 and KRAKEN2023 device kinds */
 static int kraken3_read_z53(struct kraken3_data *priv)
 {
 	int ret = mutex_lock_interruptible(&priv->z53_status_request_lock);
@@ -355,6 +360,13 @@ static int kraken3_write_curve(struct kraken3_data *priv, u8 *curve_array, int c
 	/* Set the correct ID for writing pump/fan duty (0x01 or 0x02, respectively) */
 	fixed_duty_cmd[SET_DUTY_ID_OFFSET] = channel + 1;
 
+	if (priv->kind == KRAKEN2023) {
+		/* These require 1s in the next one or two slots after SET_DUTY_ID_OFFSET */
+		fixed_duty_cmd[SET_DUTY_ID_OFFSET + 1] = 1;
+		if (channel == 1) /* Fan */
+			fixed_duty_cmd[SET_DUTY_ID_OFFSET + 2] = 1;
+	}
+
 	/* Copy curve to command */
 	memcpy(fixed_duty_cmd + SET_CURVE_DUTY_CMD_HEADER_LENGTH, curve_array, CUSTOM_CURVE_POINTS);
 
@@ -502,8 +514,8 @@ static umode_t kraken3_curve_props_are_visible(struct kobject *kobj, struct attr
 	struct device *dev = kobj_to_dev(kobj);
 	struct kraken3_data *priv = dev_get_drvdata(dev);
 
-	/* Only Z53 has the fan curve */
-	if (index >= CUSTOM_CURVE_POINTS && priv->kind != Z53)
+	/* X53 does not have a fan */
+	if (index >= CUSTOM_CURVE_POINTS && priv->kind == X53)
 		return 0;
 
 	return attr->mode;
@@ -769,8 +781,8 @@ static int kraken3_raw_event(struct hid_device *hdev, struct hid_report *report,
 	if (priv->kind == X53 && !completion_done(&priv->status_report_processed)) {
 		/* Mark first X-series device report as received */
 		complete_all(&priv->status_report_processed);
-	} else if (priv->kind == Z53) {
-		/* Additional readings for Z53 */
+	} else if (priv->kind == Z53 || priv->kind == KRAKEN2023) {
+		/* Additional readings for Z53 and KRAKEN2023 */
 		priv->fan_input[1] = get_unaligned_le16(data + Z53_FAN_SPEED_OFFSET);
 		priv->channel_info[1].reported_duty =
 		    kraken3_percent_to_pwm(data[Z53_FAN_DUTY_OFFSET]);
@@ -907,6 +919,14 @@ static int kraken3_probe(struct hid_device *hdev, const struct hid_device_id *id
 		priv->kind = Z53;
 		device_name = "z53";
 		break;
+	case USB_PRODUCT_ID_KRAKEN2023:
+		priv->kind = KRAKEN2023;
+		device_name = "kraken2023";
+		break;
+	case USB_PRODUCT_ID_KRAKEN2023_ELITE:
+		priv->kind = KRAKEN2023;
+		device_name = "kraken2023elite";
+		break;
 	default:
 		break;
 	}
@@ -969,6 +989,8 @@ static const struct hid_device_id kraken3_table[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_NZXT, USB_PRODUCT_ID_X53) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_NZXT, USB_PRODUCT_ID_X53_SECOND) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_NZXT, USB_PRODUCT_ID_Z53) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_NZXT, USB_PRODUCT_ID_KRAKEN2023) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_NZXT, USB_PRODUCT_ID_KRAKEN2023_ELITE) },
 	{ }
 };
 
-- 
2.44.0





[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux