Commit messages (was: [PATCH v4 3/3] hwmon: Driver for Nuvoton NCT7363Y)

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Dear Guenter,


Thank you for your reply.

Am 28.02.24 um 17:03 schrieb Guenter Roeck:
On 2/28/24 03:03, Paul Menzel wrote:

Am 28.02.24 um 10:03 schrieb Guenter Roeck:
On 2/27/24 23:57, Paul Menzel wrote:

Am 27.02.24 um 01:56 schrieb baneric926@xxxxxxxxx:
From: Ban Feng <kcfeng0@xxxxxxxxxxx>

NCT7363Y is an I2C based hardware monitoring chip from Nuvoton.

Please reference the datasheet.

Note that something like

Datasheet: Available from Nuvoton upon request

is quite common for hardware monitoring chips and acceptable.

Yes, it would be nice to document it though. (And finally for vendors to just make them available for download.)

Nuvoton is nice enough and commonly makes datasheets available on request.
The only exception I have seen so far is where they were forced into an NDA
by a large chip and board vendor, which prevented them from publishing a
specific datasheet.

Nice, that they are better in this regard than others.

Others are much worse. Many PMIC vendors don't publish their datasheets at
all, and sometimes chips don't even officially exist (notorious for chips
intended for the automotive market). Just look at the whole discussion
around MAX31335.

Anyway, there are lots of examples in Documentation/hwmon/. I don't see
the need to add further documentation, and I specifically don't want to
make it official that "Datasheet not public" is acceptable as well.
We really don't have a choice unless we want to exclude a whole class
of chips from the kernel, but that doesn't make it better.

I know folks figure it out eventually, but I found it helpful to have the datesheet name in the commit message to know what to search for, ask for, or in case of difference between datasheet revision what to compare against.

Could you please give a high level description of the driver design?

Can you be more specific ? I didn't have time yet to look into details,
but at first glance this looks like a standard hardware monitoring driver.
One could argue that the high level design of such drivers is described
in Documentation/hwmon/hwmon-kernel-api.rst.

I don't usually ask for a additional design information for hwmon drivers
unless some chip interaction is unusual and needs to be explained,
and then I prefer to have it explained in the code. Given that, I am
quite curious and would like to understand what you are looking for.
For a 10+ lines commit, in my opinion the commit message should say something about the implementation. Even it is just, as you wrote, a note, that it follows the standard design.

Again, I have not looked into the submission, but usually we ask for that
to be documented in Documentation/hwmon/. I find that much better than
a soon-to-be-forgotten commit message. I don't mind something like
"The NCT7363Y is a fan controller with up to 16 independent fan input
  monitors and up to 16 independent PWM outputs. It also supports up
  to 16 GPIO pins"
or in other words a description of the chip, not the implementation.
That a driver hwmon driver uses the hardware monitoring API seems to be
obvious to me, so I don't see the value of adding it to the commit
description. I would not mind having something there, but I don't
see it as mandatory.

On the  other side, granted, that is just _my_ personal opinion.
Do we have a common guideline for what exactly should be in commit
descriptions for driver submissions ? I guess I should look that up.

`Documentation/hwmon/submitting-patches.rst` refers to `Documentation/process/submitting-patches.rst`, and there *Describe your changes* seems to have been written for documenting bug fixes or enhancements and not new additions. It for example contains:

Once the problem is established, describe what you are actually doing
about it in technical detail.  It's important to describe the change
in plain English for the reviewer to verify that the code is behaving
as you intend it to.

I agree with your description, but I am also convinced if you write 500 lines of code, that you can write ten lines of commit messages giving a broad overview. In this case, saying that it follows the standard driver model would be good enough for me.

Also, at least for me, often having to bisect stuff and using `git blame` to look at old commits, commit messages are very valuable to me, and not “forgotten”. ;-)


Kind regards,

Paul




[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux