CMIS compliant modules such as QSFP-DD might be running a firmware that
can be updated in a vendor-neutral way by exchanging messages between
the host and the module as described in section 7.2.2 of revision
4.0 of the CMIS standard.
According to the CMIS standard, the firmware update process is done
using a CDB commands sequence.
CDB (Command Data Block Message Communication) reads and writes are
performed on memory map pages 9Fh-AFh according to the CMIS standard,
section 8.12 of revision 4.0.
Add a pair of new ethtool messages that allow:
* User space to trigger firmware update of transceiver modules
* The kernel to notify user space about the progress of the process
The user interface is designed to be asynchronous in order to avoid RTNL
being held for too long and to allow several modules to be updated
simultaneously. The interface is designed with CMIS compliant modules in
mind, but kept generic enough to accommodate future use cases, if these
arise.
The kernel interface that will implement the firmware update using CDB
command will include 2 layers that will be added under ethtool:
* The upper layer that will be triggered from the module layer, is
cmis_ fw_update.
* The lower one is cmis_cdb.
In the future there might be more operations to implement using CDB
commands. Therefore, the idea is to keep the cmis_cdb interface clean and
the cmis_fw_update specific to the cdb commands handling it.
The communication between the kernel and the driver will be done using
two ethtool operations that enable reading and writing the transceiver
module EEPROM.
The operation ethtool_ops::get_module_eeprom_by_page, that is already
implemented, will be used for reading from the EEPROM the CDB reply,
e.g. reading module setting, state, etc.
The operation ethtool_ops::set_module_eeprom_by_page, that is added in
the current patchset, will be used for writing to the EEPROM the CDB
command such as start firmware image, run firmware image, etc.
Therefore in order for a driver to implement module flashing, that
driver needs to implement the two functions mentioned above.
Patchset overview:
Patch #1-#2: Implement the EEPROM writing in mlxsw.
Patch #3: Define the interface between the kernel and user space.
Patch #4: Add ability to notify the flashing firmware progress.
Patch #5: Add firmware flashing in progress flag.
Patch #6: Add extended compliance codes.
Patch #7: Add the cdb layer.
Patch #8: Add the fw_update layer.
Patch #9: Add ability to flash transceiver modules' firmware.
Danielle Ratson (7):
ethtool: Add an interface for flashing transceiver modules' firmware
ethtool: Add flashing transceiver modules' firmware notifications
ability
include: netdevice: Add module firmware flashing in progress flag to
net_device
net: sfp: Add more extended compliance codes
ethtool: cmis_cdb: Add a layer for supporting CDB commands
ethtool: cmis_fw_update: add a layer for supporting firmware update
using CDB
ethtool: Add ability to flash transceiver modules' firmware
Ido Schimmel (2):
ethtool: Add ethtool operation to write to a transceiver module EEPROM
mlxsw: Implement ethtool operation to write to a transceiver module
EEPROM
Documentation/netlink/specs/ethtool.yaml | 63 +++
Documentation/networking/ethtool-netlink.rst | 62 +++
.../net/ethernet/mellanox/mlxsw/core_env.c | 57 ++
.../net/ethernet/mellanox/mlxsw/core_env.h | 6 +
drivers/net/ethernet/mellanox/mlxsw/minimal.c | 15 +
.../mellanox/mlxsw/spectrum_ethtool.c | 15 +
include/linux/ethtool.h | 20 +-
include/linux/netdevice.h | 4 +-
include/linux/sfp.h | 6 +
include/uapi/linux/ethtool.h | 18 +
include/uapi/linux/ethtool_netlink.h | 20 +
net/ethtool/Makefile | 2 +-
net/ethtool/cmis.h | 119 ++++
net/ethtool/cmis_cdb.c | 525 ++++++++++++++++++
net/ethtool/cmis_fw_update.c | 367 ++++++++++++
net/ethtool/module.c | 238 ++++++++
net/ethtool/module_fw.h | 38 ++
net/ethtool/netlink.c | 7 +
net/ethtool/netlink.h | 2 +
19 files changed, 1574 insertions(+), 10 deletions(-)
create mode 100644 net/ethtool/cmis.h
create mode 100644 net/ethtool/cmis_cdb.c
create mode 100644 net/ethtool/cmis_fw_update.c
create mode 100644 net/ethtool/module_fw.h
--
2.43.0
