as6200 is a temperature sensor with 0.0625°C resolution and a range between -40°C to 125°C. By default, the driver configures as6200 as following: - Converstion rate: 8 Hz - Conversion mode: continuous - Consecutive fault counts: 4 samples - Alert state: high polarity - Alert mode: comparator mode Interrupt is supported for the alert pin. Datasheet: https://ams.com/documents/20143/36005/AS6200_DS000449_4-00.pdf Signed-off-by: Abdel Alkuor <alkuor@xxxxxxxxx> --- Changes in v3: - Fix format for new added lm75 params - Add missing break for hwmon_temp_alarm case in lm75_is_visible - Return combined error code and status from lm75_read_config - Revert back to the previous configure setting semantics in lm75_probe - When an interrupt is tried to be requested and alarm bit is not supported then log an error instead of a warning. Also, remove the unnecessery suggestion about chips with no alarm bit. - Fix as6200 order in lm75_ids Changes in v2: - Incorporate as6200 into lm75 driver Documentation/hwmon/lm75.rst | 10 ++++ drivers/hwmon/lm75.c | 108 ++++++++++++++++++++++++++++++----- 2 files changed, 104 insertions(+), 14 deletions(-) diff --git a/Documentation/hwmon/lm75.rst b/Documentation/hwmon/lm75.rst index 8d0ab4ad5fb5..6adab608dd05 100644 --- a/Documentation/hwmon/lm75.rst +++ b/Documentation/hwmon/lm75.rst @@ -133,6 +133,16 @@ Supported chips: https://www.nxp.com/docs/en/data-sheet/PCT2075.pdf + * AMS OSRAM AS6200 + + Prefix: 'as6200' + + Addresses scanned: none + + Datasheet: Publicly available at the AMS website + + https://ams.com/documents/20143/36005/AS6200_DS000449_4-00.pdf + Author: Frodo Looijaard <frodol@xxxxxx> Description diff --git a/drivers/hwmon/lm75.c b/drivers/hwmon/lm75.c index 5b2ea05c951e..4add2563b199 100644 --- a/drivers/hwmon/lm75.c +++ b/drivers/hwmon/lm75.c @@ -7,6 +7,7 @@ #include <linux/module.h> #include <linux/init.h> +#include <linux/interrupt.h> #include <linux/slab.h> #include <linux/jiffies.h> #include <linux/i2c.h> @@ -25,6 +26,7 @@ enum lm75_type { /* keep sorted in alphabetical order */ adt75, + as6200, at30ts74, ds1775, ds75, @@ -55,6 +57,7 @@ enum lm75_type { /* keep sorted in alphabetical order */ /** * struct lm75_params - lm75 configuration parameters. + * @config_reg_16bits: Configure register size is 2 bytes. * @set_mask: Bits to set in configuration register when configuring * the chip. * @clr_mask: Bits to clear in configuration register when configuring @@ -75,17 +78,20 @@ enum lm75_type { /* keep sorted in alphabetical order */ * @sample_times: All the possible sample times to be set. Mandatory if * num_sample_times is larger than 1. If set, number of * entries must match num_sample_times. + * @alarm: Alarm bit is supported. */ struct lm75_params { - u8 set_mask; - u8 clr_mask; + bool config_reg_16bits; + u16 set_mask; + u16 clr_mask; u8 default_resolution; u8 resolution_limits; const u8 *resolutions; unsigned int default_sample_time; u8 num_sample_times; const unsigned int *sample_times; + bool alarm; }; /* Addresses scanned */ @@ -104,8 +110,8 @@ struct lm75_data { struct i2c_client *client; struct regmap *regmap; struct regulator *vs; - u8 orig_conf; - u8 current_conf; + u16 orig_conf; + u16 current_conf; u8 resolution; /* In bits, 9 to 16 */ unsigned int sample_time; /* In ms */ enum lm75_type kind; @@ -128,6 +134,15 @@ static const struct lm75_params device_params[] = { .default_resolution = 12, .default_sample_time = MSEC_PER_SEC / 10, }, + [as6200] = { + .config_reg_16bits = true, + .set_mask = 0x94C0, /* 8 sample/s, 4 CF, positive polarity */ + .default_resolution = 12, + .default_sample_time = 125, + .num_sample_times = 4, + .sample_times = (unsigned int []){ 125, 250, 1000, 4000 }, + .alarm = true, + }, [at30ts74] = { .set_mask = 3 << 5, /* 12-bit mode*/ .default_resolution = 12, @@ -317,20 +332,23 @@ static inline long lm75_reg_to_mc(s16 temp, u8 resolution) return ((temp >> (16 - resolution)) * 1000) >> (resolution - 8); } -static int lm75_write_config(struct lm75_data *data, u8 set_mask, - u8 clr_mask) +static int lm75_write_config(struct lm75_data *data, u16 set_mask, + u16 clr_mask) { - u8 value; + unsigned int value; - clr_mask |= LM75_SHUTDOWN; + clr_mask |= LM75_SHUTDOWN << (8 * data->params->config_reg_16bits); value = data->current_conf & ~clr_mask; value |= set_mask; if (data->current_conf != value) { s32 err; - - err = i2c_smbus_write_byte_data(data->client, LM75_REG_CONF, - value); + if (data->params->config_reg_16bits) + err = regmap_write(data->regmap, LM75_REG_CONF, value); + else + err = i2c_smbus_write_byte_data(data->client, + LM75_REG_CONF, + value); if (err) return err; data->current_conf = value; @@ -338,6 +356,27 @@ static int lm75_write_config(struct lm75_data *data, u8 set_mask, return 0; } +static int lm75_read_config(struct lm75_data *data) +{ + int ret; + unsigned int status; + + if (data->params->config_reg_16bits) { + ret = regmap_read(data->regmap, LM75_REG_CONF, &status); + return ret ? ret : status; + } + + return i2c_smbus_read_byte_data(data->client, LM75_REG_CONF); +} + +static irqreturn_t lm75_alarm_handler(int irq, void *private) +{ + struct device *hwmon_dev = private; + + hwmon_notify_event(hwmon_dev, hwmon_temp, hwmon_temp_alarm, 0); + return IRQ_HANDLED; +} + static int lm75_read(struct device *dev, enum hwmon_sensor_types type, u32 attr, int channel, long *val) { @@ -366,6 +405,9 @@ static int lm75_read(struct device *dev, enum hwmon_sensor_types type, case hwmon_temp_max_hyst: reg = LM75_REG_HYST; break; + case hwmon_temp_alarm: + reg = LM75_REG_CONF; + break; default: return -EINVAL; } @@ -373,7 +415,17 @@ static int lm75_read(struct device *dev, enum hwmon_sensor_types type, if (err < 0) return err; - *val = lm75_reg_to_mc(regval, data->resolution); + if (attr == hwmon_temp_alarm) { + switch (data->kind) { + case as6200: + *val = (regval >> 5) & 0x1; + break; + default: + return -EINVAL; + } + } else { + *val = lm75_reg_to_mc(regval, data->resolution); + } break; default: return -EINVAL; @@ -436,6 +488,7 @@ static int lm75_update_interval(struct device *dev, long val) data->resolution = data->params->resolutions[index]; break; case tmp112: + case as6200: err = regmap_read(data->regmap, LM75_REG_CONF, ®); if (err < 0) return err; @@ -503,6 +556,10 @@ static umode_t lm75_is_visible(const void *data, enum hwmon_sensor_types type, case hwmon_temp_max: case hwmon_temp_max_hyst: return 0644; + case hwmon_temp_alarm: + if (config_data->params->alarm) + return 0444; + break; } break; default: @@ -515,7 +572,8 @@ static const struct hwmon_channel_info * const lm75_info[] = { HWMON_CHANNEL_INFO(chip, HWMON_C_REGISTER_TZ | HWMON_C_UPDATE_INTERVAL), HWMON_CHANNEL_INFO(temp, - HWMON_T_INPUT | HWMON_T_MAX | HWMON_T_MAX_HYST), + HWMON_T_INPUT | HWMON_T_MAX | HWMON_T_MAX_HYST | + HWMON_T_ALARM), NULL }; @@ -623,7 +681,7 @@ static int lm75_probe(struct i2c_client *client) return err; /* Cache original configuration */ - status = i2c_smbus_read_byte_data(client, LM75_REG_CONF); + status = lm75_read_config(data); if (status < 0) { dev_dbg(dev, "Can't read config? %d\n", status); return status; @@ -646,6 +704,23 @@ static int lm75_probe(struct i2c_client *client) if (IS_ERR(hwmon_dev)) return PTR_ERR(hwmon_dev); + if (client->irq) { + if (data->params->alarm) { + err = devm_request_threaded_irq(dev, + client->irq, + NULL, + &lm75_alarm_handler, + IRQF_ONESHOT, + client->name, + hwmon_dev); + if (err) + return err; + } else { + /* alarm is only supported for chips with alarm bit */ + dev_err(dev, "alarm interrupt is not supported\n"); + } + } + dev_info(dev, "%s: sensor '%s'\n", dev_name(hwmon_dev), client->name); return 0; @@ -653,6 +728,7 @@ static int lm75_probe(struct i2c_client *client) static const struct i2c_device_id lm75_ids[] = { { "adt75", adt75, }, + { "as6200", as6200, }, { "at30ts74", at30ts74, }, { "ds1775", ds1775, }, { "ds75", ds75, }, @@ -689,6 +765,10 @@ static const struct of_device_id __maybe_unused lm75_of_match[] = { .compatible = "adi,adt75", .data = (void *)adt75 }, + { + .compatible = "ams,as6200", + .data = (void *)as6200 + }, { .compatible = "atmel,at30ts74", .data = (void *)at30ts74 -- 2.34.1
