On Sun, Sep 15, 2013 at 10:44 PM, Sebastian Reichel <sre@xxxxxxxxxx> wrote:
> Add SSI device tree data for OMAP34xx and Nokia N900.
>
> Signed-off-by: Sebastian Reichel <sre@xxxxxxxxxx>
> ---
> Documentation/devicetree/bindings/hsi/omap_ssi.txt | 73 ++++++++++++++++++++++
> arch/arm/boot/dts/omap3-n900.dts | 8 +++
> arch/arm/boot/dts/omap34xx.dtsi | 49 +++++++++++++++
> 3 files changed, 130 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/hsi/omap_ssi.txt
>
> diff --git a/Documentation/devicetree/bindings/hsi/omap_ssi.txt b/Documentation/devicetree/bindings/hsi/omap_ssi.txt
> new file mode 100644
> index 0000000..e3597eb
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/hsi/omap_ssi.txt
> @@ -0,0 +1,73 @@
> +OMAP SSI controller bindings
> +
> +Required properties:
> +- compatible: Should be set to the following value
> + ti,omap3-ssi (applicable to OMAP34xx devices)
> +- ti,hwmods: Name of the hwmod associated to the controller, which
> + is "ssi".
> +- reg: Contains SSI register address range (base address and
> + length).
> +- reg-names: Contains the names of the address ranges. It's
> + expected, that "sys" and "gdd" address ranges are
> + provided.
> +- interrupts: Contains the interrupt information for the controller.
> +- interrupt-names: Contains the names of the interrupts. It's expected,
> + that "gdd_mpu" is provided.
> +- ranges Required as an empty node
> +- #address-cells Should be set to <1>
> +- #size-cells Should be set to <1>
> +
> +Each port is represented as a sub-node of the ti,omap3-ssi device.
> +
> +Required Port sub-node properties:
> +- compatible: Should be set to the following value
> + ti,omap3-ssi-port (applicable to OMAP34xx devices)
> +- reg: Contains port's register address range (base address
> + and length).
> +- reg-names: Contains the names of the address ranges. It's
> + expected, that "tx" and "rx" address ranges are
> + provided.
> +- interrupt-parent Should be a phandle for the interrupt controller
> +- interrupts: Contains the interrupt information for the port.
> +- interrupt-names: Contains the names of the interrupts. It's expected,
> + that "mpu_irq0" and "mpu_irq1" are provided.
> +- ti,ssi-cawake-gpio: Defines which GPIO pin is used to signify CAWAKE
> + events for the port. This is an optional board-specific
> + property. If it's missing the port will not be
> + enabled.
> +
> +Example for Nokia N900:
> +
> +ssi-controller@48058000 {
> + compatible = "ti,omap3-ssi";
> + ti,hwmods = "ssi";
> +
> + reg = <0x48058000 0x1000>,
> + <0x48059000 0x1000>;
> + reg-names = "sys",
> + "gdd";
> +
> + interrupts = <55>;
> + interrupt-names = "gdd_mpu";
> +
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + ssi-port@0 {
> + compatible = "ti,omap3-ssi-port";
> +
> + reg = <0x4805a000 0x800>,
> + <0x4805a800 0x800>;
> + reg-names = "tx",
> + "rx";
> +
> + interrupt-parent = <&intc>;
> + interrupts = <51>,
> + <52>;
> + interrupt-names = "mpu_irq0",
> + "mpu_irq1";
> +
> + ti,ssi-cawake-gpio = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* 151 */
> + }
> +}
> diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
> index 0582356..cc4a3e2 100644
> --- a/arch/arm/boot/dts/omap3-n900.dts
> +++ b/arch/arm/boot/dts/omap3-n900.dts
> @@ -186,6 +186,14 @@
> power = <50>;
> };
>
> +&ssi_port1 {
> + ti,ssi-cawake-gpio = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* 151 */
> +};
> +
> +&ssi_port2 {
> + status = "disabled";
> +};
> +
> &uart1 {
> pinctrl-names = "default";
> pinctrl-0 = <&uart1_pins>;
> diff --git a/arch/arm/boot/dts/omap34xx.dtsi b/arch/arm/boot/dts/omap34xx.dtsi
> index 5355d61..393b7a7 100644
> --- a/arch/arm/boot/dts/omap34xx.dtsi
> +++ b/arch/arm/boot/dts/omap34xx.dtsi
> @@ -25,4 +25,53 @@
> clock-latency = <300000>; /* From legacy driver */
> };
> };
> +
> + ocp {
> + ssi: ssi-controller@48058000 {
> + compatible = "ti,omap3-ssi";
> + ti,hwmods = "ssi";
> +
> + reg = <0x48058000 0x1000>,
> + <0x48059000 0x1000>;
> + reg-names = "sys",
> + "gdd";
> +
> + interrupts = <55>;
> + interrupt-names = "gdd_mpu";
> +
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + ssi_port1: ssi-port@0 {
> + compatible = "ti,omap3-ssi-port";
> +
> + reg = <0x4805a000 0x800>,
> + <0x4805a800 0x800>;
> + reg-names = "tx",
> + "rx";
> +
> + interrupt-parent = <&intc>;
> + interrupts = <51>,
> + <52>;
> + interrupt-names = "mpu_irq0",
> + "mpu_irq1";
> + };
> +
> + ssi_port2: ssi-port@1 {
> + compatible = "ti,omap3-ssi-port";
> +
> + reg = <0x4805b000 0x800>,
> + <0x4805b800 0x800>;
> + reg-names = "tx",
> + "rx";
> +
> + interrupt-parent = <&intc>;
> + interrupts = <53>,
> + <54>;
> + interrupt-names = "mpu_irq0",
> + "mpu_irq1";
> + };
> + };
> + };
> };
> --
> 1.8.4.rc3
Hi Sebastian,
Is the Synchronous Serial Interface (SSI) only supported by
OMAP34xx/OMAP35xx SoC and not by OMAP36xx/OMAP37xx SoC?
I'm asking this since if SSI is supported by both we should add the
device nodes in omap3.dtsi instead of omap34xx.dtsi.
I thought that all OMAP3 SoC supported SSI and all OMAP4 SoC supported
HSI but I guess I was wrong...
Thanks a lot and best regards,
Javier
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
