Re: [PATCH v3 1/2] dt-bindings: hwmon: Add LTC4282 bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Dec 06, 2023 at 09:38:11AM +0100, Nuno Sá wrote:
> On Tue, 2023-12-05 at 16:18 +0000, Conor Dooley wrote:
> > On Tue, Dec 05, 2023 at 04:22:55PM +0100, Nuno Sa via B4 Relay wrote:
> > 
> > > +  adi,overvoltage-dividers:
> > > +    description: |
> > > +      Select which dividers to use for VDD Overvoltage detection. Note that
> > > +      when the internal dividers are used the threshold is referenced to VDD.
> > > +      The percentages in the datasheet are misleading since the actual values
> > > +      to look for are in the "Absolute Maximum Ratings" table in the
> > > +      "Comparator Inputs" section. In there there's a line for each of the 5%,
> > > +      10% and 15% settings with the actual min, typical and max tolerances.
> > > +    $ref: /schemas/types.yaml#/definitions/string
> > > +    enum: [external, vdd_5_percent, vdd_10_percent, vdd_15_percent]
> > > +
> > > +  adi,undervoltage-dividers:
> > > +    description: |
> > > +      Select which dividers to use for VDD Overvoltage detection. Note that
> > > +      when the internal dividers are used the threshold is referenced to VDD.
> > > +      The percentages in the datasheet are misleading since the actual values
> > > +      to look for are in the "Absolute Maximum Ratings" table in the
> > > +      "Comparator Inputs" section. In there there's a line for each of the 5%,
> > > +      10% and 15% settings with the actual min, typical and max tolerances.
> > > +    $ref: /schemas/types.yaml#/definitions/string
> > > +    enum: [external, vdd_5_percent, vdd_10_percent, vdd_15_percent]
> > 
> > > +  adi,gpio1-mode:
> > > +    description: Defines the function of the Pin. It can indicate that power is
> > > +      good (PULL the pin low when power is not good) or that power is bad (Go
> > > +      into high-z when power is not good).
> > > +    $ref: /schemas/types.yaml#/definitions/string
> > > +    enum: [power_bad, power_good]
> > > +
> > > +  adi,gpio2-mode:
> > > +    description: Defines the function of the Pin. It can be set as the input for
> > > +      the ADC or indicating that the MOSFET is in stress (dissipating power).
> > > +    $ref: /schemas/types.yaml#/definitions/string
> > > +    enum: [adc_input, stress_fet]
> > 
> > None of these properties have a default nor are required.
> > What happens when they are omitted?
> > 
> 
> Yeah, they get the power on reset default values (or whatever is in eeprom but that's
> not the typical usecase). I'll add a default for all these properties. Your question
> already made me realize something I need to fix for v4. For some reason, I thought
> gpio3 was the default pin to be muxed into the ADC (and hence monitored by hwmon) but
> I realized that gpio2 is the default one. Hence, I need a boolean property to allow
> for users to mux gpio3 instead of gpio2.

:+1: patch should be good to go then IMO with those defaults added and
the mux one fixed.

Thanks,
Conor.

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux