Re: [PATCH v3 1/3] extcon: extcon-gpio-usbvid: Generic USB VBUS/ID detection via GPIO

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 08/28/2013 11:33 AM, George Cherian wrote:
> Add a generic USB VBUS/ID detection EXTCON driver. This driver expects
> the ID/VBUS pin are connected via GPIOs. This driver is tested on
> DRA7x board were the ID pin is routed via GPIOs. The driver supports
> both VBUS and ID pin configuration and ID pin only configuration.

> diff --git a/Documentation/devicetree/bindings/extcon/extcon-gpio-usbvid.txt b/Documentation/devicetree/bindings/extcon/extcon-gpio-usbvid.txt

> +EXTCON FOR USB VIA GPIO

Please write a brief explanation of the HW that this binding represents.

"Extcon" is a Linux-specific term. Binding documentation should be
written in an OS-agnostic manner. Bindings should not reference
OS-specific terminology, and should be a pure description of the HW.

> +Required Properties:
> + - compatible : Should be "ti,gpio-usb-vid" for USB VBUS-ID detector
> +		using gpios or "ti,gpio-usb-id" for USB ID pin detector

Those souond like two rather different things. Should they be separate
bindings, or at the least, separate sections in the document?

If this binding is meant to represent some generic hardware, the vendor
prefix probably isn't required. So, remove "ti," from the compatible values.

> + - gpios : phandle and args ID pin gpio and VBUS gpio.

s/and args/and specifier/.

> +	   The first gpio used  for ID pin detection
> +	   and the second used for VBUS detection.
> +	   ID pin gpio is mandatory and VBUS is optional
> +	   depending on implementation.

It'd be better to use named GPIO properties here, rather than having
multiple different kinds of GPIO in the same property. How about
"id-gpios" and "vbus-gpios" as the property names?

The semantics of each property should be specified. Are these input
GPIOs that reflect the ID and VBUS state? Do they directly represent the
signal state on the connector, or are they processed somehow? Does the
VBUS GPIO control the board's VBUS output, or is it an input? If it
controls VBUS output, it probably should be represented as a regulator
rather than a GPIO.

I think the following might work:

Required properties:

id-gpios: GPIO specifier for the connector's ID pin input. This directly
represents the value present on the ID pin at the connector.

Optional properties:

vbus-gpios: GPIO specifier for the connector's VBUS signal. This
directly represents whether VBUS being driven by the USB cable itself.

(although perhaps that isn't an optional property, but rather a required
property of the second compatible value?)

> +Please refer to ../gpio/gpio.txt for details of the common GPIO bindings
> +
> +Example:
> +
> +	gpio_usbvid_extcon1 {
> +		compatible = "ti,gpio-usb-vid";
> +		gpios = <&gpio1 1 0>,
> +			<&gpio2 2 0>;
> +	};

--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux