Re: [RFC PATCH 2/3] pinctrl: at91: add support for generic pinconf

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 23:37 Sat 24 Aug     , Boris BREZILLON wrote:
> Add support for generic pin configuration to pinctrl-at91 driver.
> 
> Signed-off-by: Boris BREZILLON <b.brezillon@xxxxxxxxxxx>
> ---
>  .../bindings/pinctrl/atmel,at91-pinctrl.txt        |   43 +++-
>  drivers/pinctrl/Kconfig                            |    2 +-
>  drivers/pinctrl/pinctrl-at91.c                     |  265 ++++++++++++++++++--
>  3 files changed, 289 insertions(+), 21 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
> index 7ccae49..7a7c0c4 100644
> --- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
> @@ -18,7 +18,9 @@ mode) this pin can work on and the 'config' configures various pad settings
>  such as pull-up, multi drive, etc.
>  
>  Required properties for iomux controller:
> -- compatible: "atmel,at91rm9200-pinctrl"
> +- compatible: "atmel,at91rm9200-pinctrl" or "atmel,at91sam9x5-pinctrl".
> +  Add "generic-pinconf" to the compatible string list to use the generic pin
> +  configuration syntax.
>  - atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be
>    configured in this periph mode. All the periph and bank need to be describe.
>  
> @@ -83,6 +85,11 @@ Required properties for pin configuration node:
>    setting. The format is atmel,pins = <PIN_BANK PIN_BANK_NUM PERIPH CONFIG>.
>    The PERIPH 0 means gpio, PERIPH 1 is periph A, PERIPH 2 is periph B...
>    PIN_BANK 0 is pioA, PIN_BANK 1 is pioB...
> +  Dependending on the presence of the "generic-pinconf" string in the
> +  compatible property the 4th cell is:
> +   * a phandle referencing a generic pin config node (refer to
> +     pinctrl-bindings.txt)
> +   * an integer defining the pin config (see the following description)
>  
>  Bits used for CONFIG:
>  PULL_UP		(1 << 0): indicate this pin need a pull up.
> @@ -132,6 +139,40 @@ pinctrl@fffff400 {
>  	};
>  };
>  
> +or
> +
> +pinctrl@fffff400 {
> +	#address-cells = <1>;
> +	#size-cells = <1>;
> +	ranges;
> +	compatible = "atmel,at91rm9200-pinctrl", "generic-pinconf", "simple-bus";
nack your break the backword compatibility

if we use a old kernel with this new dt nothing will work
as the old kernel will never known the the "generic-pinconf" means anything

if we want to use generic-pinconf support you *CAN NOT* use atmel,at91rm9200-pinctrl
in the compatible
> +	reg = <0xfffff400 0x600>;
> +
> +	atmel,mux-mask = <
> +	      /*    A         B     */
> +	       0xffffffff 0xffc00c3b  /* pioA */
> +	       0xffffffff 0x7fff3ccf  /* pioB */
> +	       0xffffffff 0x007fffff  /* pioC */
> +	      >;
> +
> +	pcfg_none: pcfg_none {
> +		bias-disable;
> +	};
> +
> +	pcfg_pull_up: pcfg_pull_up {
> +		bias-pullup;
> +	};
> +
> +	/* shared pinctrl settings */
> +	dbgu {
> +		pinctrl_dbgu: dbgu-0 {
> +			atmel,pins =
> +				<1 14 0x1 &pcfg_none		/* PB14 periph A */
> +				 1 15 0x1 &pcfg_pull_up>;	/* PB15 periph A with pullup */
> +		};
> +	};
> +};
> +
>  dbgu: serial@fffff200 {
>  	compatible = "atmel,at91sam9260-usart";
>  	reg = <0xfffff200 0x200>;
> diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
> index bdb1a87..55a4f2c 100644
> --- a/drivers/pinctrl/Kconfig
> +++ b/drivers/pinctrl/Kconfig
> @@ -54,7 +54,7 @@ config PINCTRL_AT91
>  	depends on OF
>  	depends on ARCH_AT91
>  	select PINMUX
> -	select PINCONF
> +	select GENERIC_PINCONF
>  	help
>  	  Say Y here to enable the at91 pinctrl driver
>  
> diff --git a/drivers/pinctrl/pinctrl-at91.c b/drivers/pinctrl/pinctrl-at91.c
> index 7cce066..1994dd2 100644
> --- a/drivers/pinctrl/pinctrl-at91.c
> +++ b/drivers/pinctrl/pinctrl-at91.c
> @@ -23,6 +23,7 @@
>  #include <linux/gpio.h>
>  #include <linux/pinctrl/machine.h>
>  #include <linux/pinctrl/pinconf.h>
> +#include <linux/pinctrl/pinconf-generic.h>
>  #include <linux/pinctrl/pinctrl.h>
>  #include <linux/pinctrl/pinmux.h>
>  /* Since we request GPIOs from ourself */
> @@ -32,6 +33,7 @@
>  #include <mach/at91_pio.h>
>  
>  #include "core.h"
> +#include "pinconf.h"
>  
>  #define MAX_NB_GPIO_PER_BANK	32
>  
> @@ -85,6 +87,21 @@ enum at91_mux {
>  	AT91_MUX_PERIPH_D = 4,
>  };
>  
> +struct at91_generic_pinconf {
> +	unsigned long	*configs;
> +	unsigned int	nconfigs;
> +};
> +
> +enum at91_pinconf_type {
> +	AT91_PINCONF_NATIVE,
> +	AT91_PINCONF_GENERIC,
> +};
> +
> +union at91_pinconf {
> +	unsigned long			native;
> +	struct at91_generic_pinconf	generic;
> +};
> +
>  /**
>   * struct at91_pmx_pin - describes an At91 pin mux
>   * @bank: the bank of the pin
> @@ -93,10 +110,11 @@ enum at91_mux {
>   * @conf: the configuration of the pin: PULL_UP, MULTIDRIVE etc...
>   */
>  struct at91_pmx_pin {
> -	uint32_t	bank;
> -	uint32_t	pin;
> -	enum at91_mux	mux;
> -	unsigned long	conf;
> +	uint32_t		bank;
> +	uint32_t		pin;
> +	enum at91_mux		mux;
> +	enum at91_pinconf_type	conftype;
> +	union at91_pinconf	conf;
>  };
>  
>  /**
> @@ -278,8 +296,16 @@ static int at91_dt_node_to_map(struct pinctrl_dev *pctldev,
>  		new_map[i].type = PIN_MAP_TYPE_CONFIGS_PIN;
>  		new_map[i].data.configs.group_or_pin =
>  				pin_get_name(pctldev, grp->pins[i]);
> -		new_map[i].data.configs.configs = &grp->pins_conf[i].conf;
> -		new_map[i].data.configs.num_configs = 1;
> +		if (!pctldev->desc->confops->is_generic) {
> +			new_map[i].data.configs.configs =
> +				&grp->pins_conf[i].conf.native;
> +			new_map[i].data.configs.num_configs = 1;
> +		} else {
> +			new_map[i].data.configs.configs =
> +				grp->pins_conf[i].conf.generic.configs;
> +			new_map[i].data.configs.num_configs =
> +				grp->pins_conf[i].conf.generic.nconfigs;
> +		}
>  	}
>  
>  	dev_dbg(pctldev->dev, "maps: function %s group %s num %d\n",
> @@ -325,7 +351,7 @@ static void at91_mux_disable_interrupt(void __iomem *pio, unsigned mask)
>  
>  static unsigned at91_mux_get_pullup(void __iomem *pio, unsigned pin)
>  {
> -	return (readl_relaxed(pio + PIO_PUSR) >> pin) & 0x1;
> +	return !((readl_relaxed(pio + PIO_PUSR) >> pin) & 0x1);
>  }
>  
>  static void at91_mux_set_pullup(void __iomem *pio, unsigned mask, bool on)
> @@ -407,6 +433,16 @@ static enum at91_mux at91_mux_get_periph(void __iomem *pio, unsigned mask)
>  	return select + 1;
>  }
>  
> +static bool at91_mux_get_output(void __iomem *pio, unsigned pin)
> +{
> +	return (readl_relaxed(pio + PIO_OSR) >> pin) & 0x1;
> +}
> +
> +static void at91_mux_set_output(void __iomem *pio, unsigned mask, bool is_on)
> +{
> +	__raw_writel(mask, pio + (is_on ? PIO_OER : PIO_ODR));
> +}
> +
>  static bool at91_mux_get_deglitch(void __iomem *pio, unsigned pin)
>  {
>  	return (__raw_readl(pio + PIO_IFSR) >> pin) & 0x1;
> @@ -445,7 +481,7 @@ static void at91_mux_pio3_set_debounce(void __iomem *pio, unsigned mask,
>  
>  static bool at91_mux_pio3_get_pulldown(void __iomem *pio, unsigned pin)
>  {
> -	return (__raw_readl(pio + PIO_PPDSR) >> pin) & 0x1;
> +	return !((__raw_readl(pio + PIO_PPDSR) >> pin) & 0x1);
>  }
>  
>  static void at91_mux_pio3_set_pulldown(void __iomem *pio, unsigned mask, bool is_on)
> @@ -492,12 +528,17 @@ static struct at91_pinctrl_mux_ops at91sam9x5_ops = {
>  static void at91_pin_dbg(const struct device *dev, const struct at91_pmx_pin *pin)
>  {
>  	if (pin->mux) {
> -		dev_dbg(dev, "pio%c%d configured as periph%c with conf = 0x%lu\n",
> -			pin->bank + 'A', pin->pin, pin->mux - 1 + 'A', pin->conf);
> +		dev_dbg(dev, "pio%c%d configured as periph%c",
> +			pin->bank + 'A', pin->pin, pin->mux - 1 + 'A');
>  	} else {
> -		dev_dbg(dev, "pio%c%d configured as gpio with conf = 0x%lu\n",
> -			pin->bank + 'A', pin->pin, pin->conf);
> +		dev_dbg(dev, "pio%c%d configured as gpio",
> +			pin->bank + 'A', pin->pin);
>  	}
> +
> +	if (pin->conftype == AT91_PINCONF_NATIVE)
> +		dev_dbg(dev, " with conf = 0x%lu\n", pin->conf.native);
> +	else
> +		dev_dbg(dev, "\n");

do not change debug output
>  }
>  
>  static int pin_check_config(struct at91_pinctrl *info, const char *name,
> @@ -782,6 +823,157 @@ static const struct pinconf_ops at91_pinconf_ops = {
>  	.pin_config_group_dbg_show	= at91_pinconf_group_dbg_show,
>  };
>  
> +static int at91_generic_pinconf_get(struct pinctrl_dev *pctldev,
> +				    unsigned pin_id, unsigned long *config)
> +{
> +	struct at91_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
> +	enum pin_config_param param = pinconf_to_config_param(*config);
> +	void __iomem *pio = pin_to_controller(info, pin_to_bank(pin_id));
> +	unsigned pin = pin_id % MAX_NB_GPIO_PER_BANK;
> +	int div;
> +
> +	switch (param) {
> +	case PIN_CONFIG_BIAS_DISABLE:
> +		if (at91_mux_get_pullup(pio, pin) &&
> +		    (info->ops->get_pulldown ||
> +		     !info->ops->get_pulldown(pio, pin)))
> +			return -EINVAL;
> +
> +		*config = 0;
> +		break;
> +	case PIN_CONFIG_BIAS_PULL_UP:
> +		if (!at91_mux_get_pullup(pio, pin))
> +			return -EINVAL;
> +
> +		*config = 0;
> +		break;
> +	case PIN_CONFIG_BIAS_PULL_DOWN:
> +		if (!info->ops->get_pulldown)
> +			return -ENOTSUPP;
> +		if (!info->ops->get_pulldown(pio, pin))
> +			return -EINVAL;
> +
> +		*config = 0;
> +		break;
> +	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
> +		if (!at91_mux_get_multidrive(pio, pin))
> +			return -EINVAL;
> +
> +		*config = 0;
> +		break;
> +	case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
> +		if (!info->ops->get_schmitt_trig)
> +			return -ENOTSUPP;
> +
> +		if (!(info->ops->get_schmitt_trig(pio, pin)))
> +			*config = 1;
> +		else
> +			*config = 0;
> +		break;
> +	case PIN_CONFIG_INPUT_DEBOUNCE:
> +		if (!info->ops->get_debounce)
> +			return -ENOTSUPP;
> +
> +		if (info->ops->get_debounce(pio, pin, &div)) {
> +			/* TODO: replace 32768 with clk_get_rate(slck) return */
> +			*config = ((div + 1) * 2) * 1000000 / 32768;
> +			if (*config > 0xffff)
> +				*config = 0xffff;
> +		} else
> +			*config = 0;
> +		break;
> +	case PIN_CONFIG_INPUT_DEGLITCH:
> +		if (!info->ops->get_deglitch)
> +			return -ENOTSUPP;
> +
> +		*config = info->ops->get_deglitch(pio, pin);
> +		break;
> +	case PIN_CONFIG_OUTPUT:
> +		if (info->ops->get_periph(pio, pin) != AT91_MUX_GPIO)
> +			return -EINVAL;
> +
> +		*config = at91_mux_get_output(pio, pin);
> +		break;
> +	default:
> +		return -ENOTSUPP;
> +		break;
> +	}
> +
> +	return 0;
> +}
> +
> +static int at91_generic_pinconf_set(struct pinctrl_dev *pctldev,
> +				    unsigned pin_id, unsigned long config)
> +{
> +	struct at91_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
> +	enum pin_config_param param = pinconf_to_config_param(config);
> +	u16 arg = pinconf_to_config_argument(config);
> +	u32 div = 0;
> +	unsigned pin = pin_id % MAX_NB_GPIO_PER_BANK;
> +	unsigned mask = pin_to_mask(pin);
> +	void __iomem *pio = pin_to_controller(info, pin_to_bank(pin_id));
> +
> +	switch (param) {
> +	case PIN_CONFIG_BIAS_DISABLE:
> +		at91_mux_set_pullup(pio, mask, 0);
> +		if (info->ops->set_pulldown)
> +			info->ops->set_pulldown(pio, mask, 0);
> +		break;
> +	case PIN_CONFIG_BIAS_PULL_UP:
> +		at91_mux_set_pullup(pio, mask, arg);
> +		break;
> +	case PIN_CONFIG_BIAS_PULL_DOWN:
> +		if (!info->ops->set_pulldown)
> +			return -ENOTSUPP;
> +		info->ops->set_pulldown(pio, mask, arg);
> +		break;
> +	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
> +		at91_mux_set_multidrive(pio, mask, 1);
> +		break;
> +	case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
> +		if (!info->ops->disable_schmitt_trig)
> +			return -ENOTSUPP;
> +		if (arg)
> +			mask = ~mask;
> +		info->ops->disable_schmitt_trig(pio, mask);
> +		break;
> +	case PIN_CONFIG_INPUT_DEBOUNCE:
> +		if (!info->ops->set_debounce)
> +			return -ENOTSUPP;
> +
> +		/* TODO: replace 32768 with clk_get_rate(slck) return */
> +		if (arg) {
> +			div = (arg * 32768 / (2 * 1000000));
> +			if (div)
> +				div--;
> +		}
> +		info->ops->set_debounce(pio, mask, arg ? 1 : 0, div);
> +		break;
> +	case PIN_CONFIG_INPUT_DEGLITCH:
> +		if (!info->ops->set_deglitch)
> +			return -ENOTSUPP;
> +
> +		info->ops->set_deglitch(pio, mask, arg ? 1 : 0);
> +		break;
> +	case PIN_CONFIG_OUTPUT:
> +		if (info->ops->get_periph(pio, pin) != AT91_MUX_GPIO)
> +			return -EINVAL;
> +		at91_mux_set_output(pio, mask, arg);
> +		break;
> +	default:
> +		return -ENOTSUPP;
> +		break;
> +	}
> +
> +	return 0;
> +}
> +
> +static const struct pinconf_ops at91_generic_pinconf_ops = {
> +	.is_generic			= true,
> +	.pin_config_get			= at91_generic_pinconf_get,
> +	.pin_config_set			= at91_generic_pinconf_set,
> +};
> +
>  static struct pinctrl_desc at91_pinctrl_desc = {
>  	.pctlops	= &at91_pctrl_ops,
>  	.pmxops		= &at91_pmx_ops,
> @@ -847,6 +1039,7 @@ static int at91_pinctrl_parse_groups(struct device_node *np,
>  	int size;
>  	const __be32 *list;
>  	int i, j;
> +	int err;
>  
>  	dev_dbg(info->dev, "group(%d): %s\n", index, np->name);
>  
> @@ -870,21 +1063,48 @@ static int at91_pinctrl_parse_groups(struct device_node *np,
>  				GFP_KERNEL);
>  	grp->pins = devm_kzalloc(info->dev, grp->npins * sizeof(unsigned int),
>  				GFP_KERNEL);
> -	if (!grp->pins_conf || !grp->pins)
> -		return -ENOMEM;
> +	if (!grp->pins_conf || !grp->pins) {
> +		err = -ENOMEM;
> +		goto out_err;
> +	}

why ???
>  
>  	for (i = 0, j = 0; i < size; i += 4, j++) {
>  		pin->bank = be32_to_cpu(*list++);
>  		pin->pin = be32_to_cpu(*list++);
>  		grp->pins[j] = pin->bank * MAX_NB_GPIO_PER_BANK + pin->pin;
>  		pin->mux = be32_to_cpu(*list++);
> -		pin->conf = be32_to_cpu(*list++);
> +		if (at91_pinctrl_desc.confops->is_generic) {
> +			struct device_node *np_config;
> +			const __be32 *phandle =	list++;
> +
> +			if (!phandle) {
> +				err = -EINVAL;
> +				goto out_err;
> +			}
> +			np_config =
> +				of_find_node_by_phandle(be32_to_cpup(phandle));
> +			pin->conftype = AT91_PINCONF_GENERIC;
> +			err = pinconf_generic_parse_dt_config(np_config,
> +						&pin->conf.generic.configs,
> +						&pin->conf.generic.nconfigs);
> +			if (err)
> +				goto out_err;
> +
> +		} else {
> +			pin->conftype = AT91_PINCONF_NATIVE;
> +			pin->conf.native = be32_to_cpu(*list++);
> +		}
>  
>  		at91_pin_dbg(info->dev, pin);
>  		pin++;
>  	}
>  
>  	return 0;
> +
> +out_err:
> +	kfree(grp->pins_conf);
> +	kfree(grp->pins);
use devm and drop those kfree
> +	return err;
>  }
>  
>  static int at91_pinctrl_parse_functions(struct device_node *np,
> @@ -904,10 +1124,10 @@ static int at91_pinctrl_parse_functions(struct device_node *np,
>  	/* Initialise function */
>  	func->name = np->name;
>  	func->ngroups = of_get_child_count(np);
> -	if (func->ngroups <= 0) {
> -		dev_err(info->dev, "no groups defined\n");
> -		return -EINVAL;
> -	}
> +	/* This node might be a generic config definition: silently ignore it */
> +	if (func->ngroups <= 0)
> +		return 0;
> +
>  	func->groups = devm_kzalloc(info->dev,
>  			func->ngroups * sizeof(char *), GFP_KERNEL);
>  	if (!func->groups)
> @@ -930,6 +1150,11 @@ static struct of_device_id at91_pinctrl_of_match[] = {
>  	{ /* sentinel */ }
>  };
>  
> +static struct of_device_id at91_pinconf_of_match[] = {
> +	{ .compatible = "generic-pinconf" },
> +	{ /* sentinel */ }
> +};
> +
>  static int at91_pinctrl_probe_dt(struct platform_device *pdev,
>  				 struct at91_pinctrl *info)
>  {
> @@ -945,6 +1170,8 @@ static int at91_pinctrl_probe_dt(struct platform_device *pdev,
>  	info->dev = &pdev->dev;
>  	info->ops = (struct at91_pinctrl_mux_ops *)
>  		of_match_device(at91_pinctrl_of_match, &pdev->dev)->data;
> +	if (of_match_device(at91_pinconf_of_match, &pdev->dev))
> +		at91_pinctrl_desc.confops = &at91_generic_pinconf_ops;
>  	at91_pinctrl_child_count(info, np);
>  
>  	if (info->nbanks < 1) {
> -- 
> 1.7.9.5
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux