于 2013年08月26日 14:22, Sourav Poddar 写道:
Hi,
On Monday 26 August 2013 10:11 AM, Huang Shijie wrote:
This patch adds the DDR quad read support by:
(1) Add the relative commands:
OPCODE_DDRQIOR, OPCODE_4DDRQIOR
(2) add the "m25p,ddr-quad-read" property for the m25p80 driver
If the dts has the "m25p,ddr-quad-read" property, the kernel will
set the Quad bit of the configuration register, and when the
setting suceedes, we will set the read opcode with the right
spi nor command.
Signed-off-by: Huang Shijie<b32955@xxxxxxxxxxxxx>
---
Documentation/devicetree/bindings/mtd/m25p80.txt | 5 +++++
drivers/mtd/devices/m25p80.c | 21 ++++++++++++++++-----
include/linux/mtd/spi-nor.h | 2 ++
3 files changed, 23 insertions(+), 5 deletions(-)
diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt
b/Documentation/devicetree/bindings/mtd/m25p80.txt
index b33313f..a01c6b7 100644
--- a/Documentation/devicetree/bindings/mtd/m25p80.txt
+++ b/Documentation/devicetree/bindings/mtd/m25p80.txt
@@ -22,6 +22,11 @@ Optional properties:
all chips and support for it can not be detected at runtime.
Refer to your chips' datasheet to check if this is supported
by your chip.
+- m25p,ddr-quad-read : Use the "ddr quad read" opcode to read data
from the chip
+ instead of the usual "read" opcode. This opcode is not
+ supported by all chips and support for it can not be detected
+ at runtime. Refer to your chips' datasheet to check if this
+ is supported by your chip.
Example:
flash: m25p80@0 {
diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c
index 0645c9f..32ccdc7 100644
--- a/drivers/mtd/devices/m25p80.c
+++ b/drivers/mtd/devices/m25p80.c
@@ -913,7 +913,8 @@ static void m25p80_check_quad_read(struct m25p
*flash, struct device_node *np)
int ret;
int sr_cr;
- if (of_property_read_bool(np, "m25p,quad-read")) {
+ if (of_property_read_bool(np, "m25p,quad-read")
+ || of_property_read_bool(np, "m25p,ddr-quad-read")) {
/* The configuration register is set by the second byte. */
sr_cr = CR_QUAD<< 8;
@@ -927,10 +928,20 @@ static void m25p80_check_quad_read(struct m25p
*flash, struct device_node *np)
if (!(ret> 0&& (ret& CR_QUAD)))
return;
- if (flash->mtd.size<= SZ_16M)
- flash->read_opcode = OPCODE_QIOR;
- else
- flash->read_opcode = OPCODE_4QIOR;
+ if (of_property_read_bool(np, "m25p,quad-read")) {
+ if (flash->mtd.size<= SZ_16M)
+ flash->read_opcode = OPCODE_QIOR;
+ else
+ flash->read_opcode = OPCODE_4QIOR;
+ return;
+ }
+
+ if (of_property_read_bool(np, "m25p,ddr-quad-read")) {
+ if (flash->mtd.size<= SZ_16M)
+ flash->read_opcode = OPCODE_DDRQIOR;
+ else
+ flash->read_opcode = OPCODE_4DDRQIOR;
+ }
I remember this getting asked in some other thread also...
Quad read need dummy bits before reading out the data, what happens
when the controller does not have LUT feature. ?
I think the controller (not the QUADSPI) should submit a patch to fix it.
There are many different kinds of READs need the dummy, take S25FSL128S
for example :
Fast-Read(dummy = 8),
Dual-Output Read(dummy = 8),
Dual I/O read(dummy = 4 for 3-byte; dummy = 2 for 4-byte)
.......
Quad i/o Read(dummy = 4)
DDR QUAD i/o Read(dummy = 8)
......................
Even the same spi command such as Dual I/O read (0xBB), different
version of chips may require different
dummies.
-------------------------------------------------------------
So, the dummies are binded with the chips, not binded with the SPI
commands.
-------------------------------------------------------------
We can not list all the dummies in the m25p_ids[] . It's not feasible.
An alternate method is to specific the dummy with the DT node, such as:
"m25p,quad-read = <4>", means this chip's Quad read needs dummy=4.
thanks
Huang Shijie
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
