On 5/8/23 05:22, Vinod Koul wrote:
> On 13-04-23, 12:05, Sean Anderson wrote:
>> This adds support for the Lynx 10G "SerDes" devices found on various NXP
>> QorIQ SoCs. There may be up to four SerDes devices on each SoC, each
>> supporting up to eight lanes. Protocol support for each SerDes is highly
>> heterogeneous, with each SoC typically having a totally different
>> selection of supported protocols for each lane. Additionally, the SerDes
>> devices on each SoC also have differing support. One SerDes will
>> typically support Ethernet on most lanes, while the other will typically
>> support PCIe on most lanes.
>>
>> There is wide hardware support for this SerDes. It is present on QorIQ
>> T-Series and Layerscape processors. Because each SoC typically has
>> specific instructions and exceptions for its SerDes, I have limited the
>> initial scope of this module to just the LS1046A and LS1088A.
>> Additionally, I have only added support for Ethernet protocols. There is
>> not a great need for dynamic reconfiguration for other protocols (except
>> perhaps for M.2 cards), so support for them may never be added.
>>
>> Nevertheless, I have tried to provide an obvious path for adding support
>> for other SoCs as well as other protocols. SATA just needs support for
>> configuring LNmSSCR0. PCIe may need to configure the equalization
>> registers. It also uses multiple lanes. I have tried to write the driver
>> with multi-lane support in mind, so there should not need to be any
>> large changes. Although there are 6 protocols supported, I have only
>> tested SGMII and XFI. The rest have been implemented as described in
>> the datasheet. Most of these protocols should work "as-is", but
>> 10GBASE-KR will need PCS support for link training.
>>
>> Unlike some other phys where e.g. PCIe x4 will use 4 separate phys all
>> configured for PCIe, this driver uses one phy configured to use 4 lanes.
>> This is because while the individual lanes may be configured
>> individually, the protocol selection acts on all lanes at once.
>> Additionally, the order which lanes should be configured in is specified
>> by the datasheet. To coordinate this, lanes are reserved in phy_init,
>> and released in phy_exit.
>>
>> This driver was written with reference to the LS1046A reference manual.
>> However, it was informed by reference manuals for all processors with
>> mEMACs, especially the T4240 (which appears to have a "maxed-out"
>> configuration). The earlier P-series processors appear to be similar, but
>> have a different overall register layout (using "banks" instead of
>> separate SerDes). Perhaps this those use a "5G Lynx SerDes."
>>
>> Note that while I have used FIELD_GET/FIELD_PREP where possible, these
>> macros require const values for the field. This is incompatible with
>> dynamicly-generated fields, such as when the field is determined by a
>> variable. In these cases, I have used traditional shift/mask techniques.
>>
>> Signed-off-by: Sean Anderson <sean.anderson@xxxxxxxx>
>> ---
>>
>> Changes in v14:
>> - Add note about (lack of) use of FIELD_GET/PREP
>>
>> Changes in v10:
>> - Fix debugging print with incorrect error variable
>>
>> Changes in v9:
>> - Split off clock "driver" into its own patch to allow for better
>> review.
>> - Add ability to defer lane initialization to phy_init. This allows
>> for easier transitioning between firmware-managed serdes and Linux-
>> managed serdes, as the consumer (such as dpaa2, which knows what the
>> firmware is doing) has the last say on who gets control.
>> - phy-type -> fsl,phy
>>
>> Changes in v8:
>> - Remove unused variable from lynx_ls_mode_init
>>
>> Changes in v7:
>> - Break out call order into generic documentation
>> - Refuse to switch "major" protocols
>> - Update Kconfig to reflect restrictions
>> - Remove set/clear of "pcs reset" bit, since it doesn't seem to fix
>> anything.
>>
>> Changes in v6:
>> - Update MAINTAINERS to include new files
>> - Include bitfield.h and slab.h to allow compilation on non-arm64
>> arches.
>> - Depend on COMMON_CLK and either layerscape/ppc
>>
>> Changes in v5:
>> - Remove references to PHY_INTERFACE_MODE_1000BASEKX to allow this
>> series to be applied directly to linux/master.
>> - Add fsl,lynx-10g.h to MAINTAINERS
>>
>> Changes in v4:
>> - Rework all debug statements to remove use of __func__. Additional
>> information has been provided as necessary.
>> - Consider alternative parent rates in round_rate and not in set_rate.
>> Trying to modify out parent's rate in set_rate will deadlock.
>> - Explicitly perform a stop/reset sequence in set_rate. This way we
>> always ensure that the PLL is properly stopped.
>> - Set the power-down bit when disabling the PLL. We can do this now that
>> enable/disable aren't abused during the set rate sequence.
>> - Fix typos in QSGMII_OFFSET and XFI_OFFSET
>> - Rename LNmTECR0_TEQ_TYPE_PRE to LNmTECR0_TEQ_TYPE_POST to better
>> reflect its function (adding post-cursor equalization).
>> - Use of_clk_hw_onecell_get instead of a custom function.
>> - Return struct clks from lynx_clks_init instead of embedding lynx_clk
>> in lynx_priv.
>> - Rework PCCR helper functions; T-series SoCs differ from Layerscape SoCs
>> primarily in the layout and offset of the PCCRs. This will help bring a
>> cleaner abstraction layer. The caps have been removed, since this handles the
>> only current usage.
>> - Convert to use new binding format. As a result of this, we no longer need to
>> have protocols for PCIe or SATA. Additionally, modes now live in lynx_group
>> instead of lynx_priv.
>> - Remove teq from lynx_proto_params, since it can be determined from
>> preq_ratio/postq_ratio.
>> - Fix an early return from lynx_set_mode not releasing serdes->lock.
>> - Rename lynx_priv.conf to .cfg, since I kept mistyping it.
>>
>> Changes in v3:
>> - Rename remaining references to QorIQ SerDes to Lynx 10G
>> - Fix PLL enable sequence by waiting for our reset request to be cleared
>> before continuing. Do the same for the lock, even though it isn't as
>> critical. Because we will delay for 1.5ms on average, use prepare
>> instead of enable so we can sleep.
>> - Document the status of each protocol
>> - Fix offset of several bitfields in RECR0
>> - Take into account PLLRST_B, SDRST_B, and SDEN when considering whether
>> a PLL is "enabled."
>> - Only power off unused lanes.
>> - Split mode lane mask into first/last lane (like group)
>> - Read modes from device tree
>> - Use caps to determine whether KX/KR are supported
>> - Move modes to lynx_priv
>> - Ensure that the protocol controller is not already in-use when we try
>> to configure a new mode. This should only occur if the device tree is
>> misconfigured (e.g. when QSGMII is selected on two lanes but there is
>> only one QSGMII controller).
>> - Split PLL drivers off into their own file
>> - Add clock for "ext_dly" instead of writing the bit directly (and
>> racing with any clock code).
>> - Use kasprintf instead of open-coding the snprintf dance
>> - Support 1000BASE-KX in lynx_lookup_proto. This still requires PCS
>> support, so nothing is truly "enabled" yet.
>>
>> Changes in v2:
>> - Rename driver to Lynx 10G (etc.)
>> - Fix not clearing group->pll after disabling it
>> - Support 1 and 2 phy-cells
>> - Power off lanes during probe
>> - Clear SGMIIaCR1_PCS_EN during probe
>> - Rename LYNX_PROTO_UNKNOWN to LYNX_PROTO_NONE
>> - Handle 1000BASE-KX in lynx_proto_mode_prep
>>
>> Documentation/driver-api/phy/index.rst | 1 +
>> Documentation/driver-api/phy/lynx_10g.rst | 58 +
>> MAINTAINERS | 2 +
>> drivers/phy/freescale/Kconfig | 18 +-
>> drivers/phy/freescale/Makefile | 1 +
>> drivers/phy/freescale/phy-fsl-lynx-10g.c | 1224 +++++++++++++++++++++
>> 6 files changed, 1303 insertions(+), 1 deletion(-)
>> create mode 100644 Documentation/driver-api/phy/lynx_10g.rst
>> create mode 100644 drivers/phy/freescale/phy-fsl-lynx-10g.c
>>
>> diff --git a/Documentation/driver-api/phy/index.rst b/Documentation/driver-api/phy/index.rst
>> index 69ba1216de72..c9b7a4698dab 100644
>> --- a/Documentation/driver-api/phy/index.rst
>> +++ b/Documentation/driver-api/phy/index.rst
>> @@ -7,6 +7,7 @@ Generic PHY Framework
>> .. toctree::
>>
>> phy
>> + lynx_10g
>> samsung-usb2
>>
>> .. only:: subproject and html
>> diff --git a/Documentation/driver-api/phy/lynx_10g.rst b/Documentation/driver-api/phy/lynx_10g.rst
>> new file mode 100644
>> index 000000000000..17f9a9580e24
>> --- /dev/null
>> +++ b/Documentation/driver-api/phy/lynx_10g.rst
>> @@ -0,0 +1,58 @@
>> +.. SPDX-License-Identifier: GPL-2.0
>> +
>> +===========================
>> +Lynx 10G Phy (QorIQ SerDes)
>> +===========================
>> +
>> +Using this phy
>> +--------------
>> +
>> +:c:func:`phy_get` just gets (or creates) a new :c:type:`phy` with the lanes
>> +described in the phandle. :c:func:`phy_init` is what actually reserves the
>> +lanes for use. Unlike some other drivers, when the phy is created, there is no
>> +default protocol. :c:func:`phy_set_mode <phy_set_mode_ext>` must be called in
>> +order to set the protocol.
>> +
>> +Supporting SoCs
>> +---------------
>> +
>> +Each new SoC needs a :c:type:`struct lynx_conf <lynx_conf>`, containing the
>> +number of lanes in each device, the endianness of the device, and the helper
>> +functions to use when selecting protocol controllers. For example, the
>> +configuration for the LS1046A is::
>> +
>> + static const struct lynx_cfg ls1046a_cfg = {
>> + .lanes = 4,
>> + .endian = REGMAP_ENDIAN_BIG,
>> + .mode_conflict = lynx_ls_mode_conflict,
>> + .mode_apply = lynx_ls_mode_apply,
>> + .mode_init = lynx_ls_mode_init,
>> + };
>> +
>> +The ``mode_`` functions will generally be common to all SoCs in a series (e.g.
>> +all Layerscape SoCs or all T-series SoCs).
>> +
>> +In addition, you will need to add a device node as documented in
>> +``Documentation/devicetree/bindings/phy/fsl,lynx-10g.yaml``. This lets the
>> +driver know which lanes are available to configure.
>> +
>> +Supporting Protocols
>> +--------------------
>> +
>> +Each protocol is a combination of values which must be programmed into the lane
>> +registers. To add a new protocol, first add it to :c:type:`enum lynx_protocol
>> +<lynx_protocol>`. Add a new entry to ``lynx_proto_params``, and populate the
>> +appropriate fields. Modify ``lynx_lookup_proto`` to map the :c:type:`enum
>> +phy_mode <phy_mode>` to :c:type:`enum lynx_protocol <lynx_protocol>`. Finally,
>> +update the ``mode_conflict``, ``mode_apply``, and ``mode_init`` helpers to
>> +support your protocol.
>> +
>> +You may need to modify :c:func:`lynx_set_mode` in order to support your
>> +protocol. This can happen when you have added members to :c:type:`struct
>> +lynx_proto_params <lynx_proto_params>`. It can also happen if you have specific
>> +clocking requirements, or protocol-specific registers to program.
>> +
>> +Internal API Reference
>> +----------------------
>> +
>> +.. kernel-doc:: drivers/phy/freescale/phy-fsl-lynx-10g.c
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 8da893681de6..870014ab14aa 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -12198,7 +12198,9 @@ T: git https://cas5-0-urlprotect.trendmicro.com:443/wis/clicktime/v1/query?url=https%3a%2f%2fgithub.com%2flinux%2dtest%2dproject%2fltp.git&umid=394d3091-283e-42bc-ac1a-f7e4ac9ff0b7&auth=d807158c60b7d2502abde8a2fc01f40662980862-97fd27a257b9136870bfe8eda3b1eecd6052c43a
>> LYNX 10G SERDES DRIVER
>> M: Sean Anderson <sean.anderson@xxxxxxxx>
>> S: Maintained
>> +F: Documentation/driver-api/phy/lynx_10g.rst
>> F: drivers/clk/clk-fsl-lynx-10g.c
>> +F: drivers/phy/freescale/phy-fsl-lynx-10g.c
>> F: include/dt-bindings/clock/fsl,lynx-10g.h
>> F: include/linux/phy/lynx-10g.h
>>
>> diff --git a/drivers/phy/freescale/Kconfig b/drivers/phy/freescale/Kconfig
>> index 5d461232276f..6bebe00f5889 100644
>> --- a/drivers/phy/freescale/Kconfig
>> +++ b/drivers/phy/freescale/Kconfig
>> @@ -49,7 +49,23 @@ config PHY_FSL_LYNX_28G
>> Only useful for a restricted set of Ethernet protocols.
>>
>> config PHY_FSL_LYNX_10G
>> - tristate
>> + tristate "Freescale QorIQ Lynx 10G SerDes support"
>> depends on COMMON_CLK
>> depends on ARCH_LAYERSCAPE || PPC || COMPILE_TEST
>> + select GENERIC_PHY
>> select REGMAP_MMIO
>> + help
>> + This adds support for the Lynx "SerDes" devices found on various QorIQ
>> + SoCs. There may be up to four SerDes devices on each SoC, and each
>> + device supports up to eight lanes. The SerDes is configured by
>> + default by the RCW, but this module is necessary in order to support
>> + some modes (such as 2.5G SGMII or 1000BASE-KX), or clock setups (as
>> + only as subset of clock configurations are supported by the RCW).
>> + The hardware supports a variety of protocols, including Ethernet,
>> + SATA, PCIe, and more exotic links such as Interlaken and Aurora. This
>> + driver only supports Ethernet, but it will try not to touch lanes
>> + configured for other protocols.
>> +
>> + If you have a QorIQ processor and want to dynamically reconfigure your
>> + SerDes, say Y. If this driver is compiled as a module, it will be
>> + named phy-fsl-lynx-10g and clk-fsl-lynx-10g.
>> diff --git a/drivers/phy/freescale/Makefile b/drivers/phy/freescale/Makefile
>> index cedb328bc4d2..32ad795be7c6 100644
>> --- a/drivers/phy/freescale/Makefile
>> +++ b/drivers/phy/freescale/Makefile
>> @@ -3,4 +3,5 @@ obj-$(CONFIG_PHY_FSL_IMX8MQ_USB) += phy-fsl-imx8mq-usb.o
>> obj-$(CONFIG_PHY_MIXEL_LVDS_PHY) += phy-fsl-imx8qm-lvds-phy.o
>> obj-$(CONFIG_PHY_MIXEL_MIPI_DPHY) += phy-fsl-imx8-mipi-dphy.o
>> obj-$(CONFIG_PHY_FSL_IMX8M_PCIE) += phy-fsl-imx8m-pcie.o
>> +obj-$(CONFIG_PHY_FSL_LYNX_10G) += phy-fsl-lynx-10g.o
>> obj-$(CONFIG_PHY_FSL_LYNX_28G) += phy-fsl-lynx-28g.o
>> diff --git a/drivers/phy/freescale/phy-fsl-lynx-10g.c b/drivers/phy/freescale/phy-fsl-lynx-10g.c
>> new file mode 100644
>> index 000000000000..880f718b387f
>> --- /dev/null
>> +++ b/drivers/phy/freescale/phy-fsl-lynx-10g.c
>> @@ -0,0 +1,1224 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Copyright (C) 2022 Sean Anderson <sean.anderson@xxxxxxxx>
>> + *
>> + * This driver is for the Lynx 10G phys found on many QorIQ devices, including
>> + * the Layerscape series.
>> + */
>> +
>> +#include <dt-bindings/phy/phy.h>
>> +#include <linux/clk.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/phy.h>
>> +#include <linux/phy/lynx-10g.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/regmap.h>
>> +
>> +#define TCALCR 0x90
>> +#define TCALCR1 0x94
>> +#define RCALCR 0xa0
>> +#define RCALCR1 0xa4
>> +
>> +#define CALCR_CALRST_B BIT(27)
>> +
>> +#define LS_PCCR_BASE 0x200
>> +#define PCCR_STRIDE 0x4
>> +
>> +#define LS_PCCRa(a) (LS_PCCR_BASE + (a) * PCCR_STRIDE)
>> +
>> +#define PCCR8_SGMIIa_KX BIT(3)
>> +#define PCCR8_SGMIIa_MASK GENMASK(3, 0)
>> +#define PCCR8_SGMIIa_SHIFT(a) (28 - (a) * 4)
>> +
>> +#define PCCR9_QSGMIIa_MASK GENMASK(2, 0)
>> +#define PCCR9_QSGMIIa_SHIFT(a) (28 - (a) * 4)
>> +
>> +#define PCCRB_XFIa_MASK GENMASK(2, 0)
>> +#define PCCRB_XFIa_SHIFT(a) (28 - (a) * 4)
>> +
>> +#define LANE_BASE 0x800
>> +#define LANE_STRIDE 0x40
>> +#define LNm(m, off) (LANE_BASE + (m) * LANE_STRIDE + (off))
>> +#define LNmGCR0(m) LNm(m, 0x00)
>> +#define LNmGCR1(m) LNm(m, 0x04)
>> +#define LNmSSCR0(m) LNm(m, 0x0C)
>> +#define LNmRECR0(m) LNm(m, 0x10)
>> +#define LNmRECR1(m) LNm(m, 0x14)
>> +#define LNmTECR0(m) LNm(m, 0x18)
>> +#define LNmSSCR1(m) LNm(m, 0x1C)
>> +#define LNmTTLCR0(m) LNm(m, 0x20)
>> +
>> +#define LNmGCR0_RPLL_LES BIT(31)
>> +#define LNmGCR0_RRAT_SEL GENMASK(29, 28)
>> +#define LNmGCR0_TPLL_LES BIT(27)
>> +#define LNmGCR0_TRAT_SEL GENMASK(25, 24)
>> +#define LNmGCR0_RRST_B BIT(22)
>> +#define LNmGCR0_TRST_B BIT(21)
>> +#define LNmGCR0_RX_PD BIT(20)
>> +#define LNmGCR0_TX_PD BIT(19)
>> +#define LNmGCR0_IF20BIT_EN BIT(18)
>> +#define LNmGCR0_FIRST_LANE BIT(16)
>> +#define LNmGCR0_TTRM_VM_SEL GENMASK(13, 12)
>> +#define LNmGCR0_PROTS GENMASK(11, 7)
>> +
>> +#define LNmGCR0_RAT_SEL_SAME 0b00
>> +#define LNmGCR0_RAT_SEL_HALF 0b01
>> +#define LNmGCR0_RAT_SEL_QUARTER 0b10
>> +#define LNmGCR0_RAT_SEL_DOUBLE 0b11
>> +
>> +#define LNmGCR0_PROTS_PCIE 0b00000
>> +#define LNmGCR0_PROTS_SGMII 0b00001
>> +#define LNmGCR0_PROTS_SATA 0b00010
>> +#define LNmGCR0_PROTS_XFI 0b01010
>> +
>> +#define LNmGCR1_RDAT_INV BIT(31)
>> +#define LNmGCR1_TDAT_INV BIT(30)
>> +#define LNmGCR1_OPAD_CTL BIT(26)
>> +#define LNmGCR1_REIDL_TH GENMASK(22, 20)
>> +#define LNmGCR1_REIDL_EX_SEL GENMASK(19, 18)
>> +#define LNmGCR1_REIDL_ET_SEL GENMASK(17, 16)
>> +#define LNmGCR1_REIDL_EX_MSB BIT(15)
>> +#define LNmGCR1_REIDL_ET_MSB BIT(14)
>> +#define LNmGCR1_REQ_CTL_SNP BIT(13)
>> +#define LNmGCR1_REQ_CDR_SNP BIT(12)
>> +#define LNmGCR1_TRSTDIR BIT(7)
>> +#define LNmGCR1_REQ_BIN_SNP BIT(6)
>> +#define LNmGCR1_ISLEW_RCTL GENMASK(5, 4)
>> +#define LNmGCR1_OSLEW_RCTL GENMASK(1, 0)
>> +
>> +#define LNmRECR0_RXEQ_BST BIT(28)
>> +#define LNmRECR0_GK2OVD GENMASK(27, 24)
>> +#define LNmRECR0_GK3OVD GENMASK(19, 16)
>> +#define LNmRECR0_GK2OVD_EN BIT(15)
>> +#define LNmRECR0_GK3OVD_EN BIT(14)
>> +#define LNmRECR0_OSETOVD_EN BIT(13)
>> +#define LNmRECR0_BASE_WAND GENMASK(11, 10)
>> +#define LNmRECR0_OSETOVD GENMASK(6, 0)
>> +
>> +#define LNmRECR0_BASE_WAND_OFF 0b00
>> +#define LNmRECR0_BASE_WAND_DEFAULT 0b01
>> +#define LNmRECR0_BASE_WAND_ALTERNATE 0b10
>> +#define LNmRECR0_BASE_WAND_OSETOVD 0b11
>> +
>> +#define LNmTECR0_TEQ_TYPE GENMASK(29, 28)
>> +#define LNmTECR0_SGN_PREQ BIT(26)
>> +#define LNmTECR0_RATIO_PREQ GENMASK(25, 22)
>> +#define LNmTECR0_SGN_POST1Q BIT(21)
>> +#define LNmTECR0_RATIO_PST1Q GENMASK(20, 16)
>> +#define LNmTECR0_ADPT_EQ GENMASK(13, 8)
>> +#define LNmTECR0_AMP_RED GENMASK(5, 0)
>> +
>> +#define LNmTECR0_TEQ_TYPE_NONE 0b00
>> +#define LNmTECR0_TEQ_TYPE_POST 0b01
>> +#define LNmTECR0_TEQ_TYPE_BOTH 0b10
>> +
>> +#define LNmTTLCR0_FLT_SEL GENMASK(29, 24)
>> +
>> +#define LS_SGMII_BASE 0x1800
>> +#define LS_QSGMII_BASE 0x1880
>> +#define LS_XFI_BASE 0x1980
>> +
>> +#define PCS_STRIDE 0x10
>> +#define CR_STRIDE 0x4
>> +#define PCSa(a, base, cr) (base + (a) * PCS_STRIDE + (cr) * CR_STRIDE)
>> +
>> +#define PCSaCR1_MDEV_PORT GENMASK(31, 27)
>> +
>> +#define LS_SGMIIaCR1(a) PCSa(a, LS_SGMII_BASE, 1)
>> +#define SGMIIaCR1_SGPCS_EN BIT(11)
>> +
>> +enum lynx_protocol {
>> + LYNX_PROTO_NONE = 0,
>> + LYNX_PROTO_SGMII,
>> + LYNX_PROTO_SGMII25, /* Not tested */
>> + LYNX_PROTO_1000BASEKX, /* Not tested */
>> + LYNX_PROTO_QSGMII, /* Not tested */
>> + LYNX_PROTO_XFI,
>> + LYNX_PROTO_10GKR, /* Link training unimplemented */
>> + LYNX_PROTO_LAST,
>> +};
>> +
>> +static const char lynx_proto_str[][16] = {
>> + [LYNX_PROTO_NONE] = "unknown",
>> + [LYNX_PROTO_SGMII] = "SGMII",
>> + [LYNX_PROTO_SGMII25] = "2.5G SGMII",
>> + [LYNX_PROTO_1000BASEKX] = "1000BASE-KX",
>> + [LYNX_PROTO_QSGMII] = "QSGMII",
>> + [LYNX_PROTO_XFI] = "XFI",
>> + [LYNX_PROTO_10GKR] = "10GBASE-KR",
>> +};
>> +
>> +#define PROTO_MASK(proto) BIT(LYNX_PROTO_##proto)
>> +
>> +/**
>> + * struct lynx_proto_params - Parameters for configuring a protocol
>> + * @frate_khz: The PLL rate, in kHz
>> + * @rat_sel: The divider to get the line rate
>> + * @if20bit: Whether the proto is 20 bits or 10 bits
>> + * @prots: Lane protocol select
>> + * @reidl_th: Receiver electrical idle detection threshold
>> + * @reidl_ex: Exit electrical idle filter
>> + * @reidl_et: Enter idle filter
>> + * @slew: Slew control
>> + * @baseline_wander: Enable baseline wander correction
>> + * @gain: Adaptive equalization gain override
>> + * @offset_override: Adaptive equalization offset override
>> + * @preq_ratio: Ratio of full swing transition bit to pre-cursor
>> + * @postq_ratio: Ratio of full swing transition bit to first post-cursor.
>> + * @adpt_eq: Transmitter Adjustments for 8G/10G
>> + * @amp_red: Overall TX Amplitude Reduction
>> + * @flt_sel: TTL configuration selector
>> + */
>> +struct lynx_proto_params {
>> + u32 frate_khz;
>> + u8 rat_sel;
>> + u8 prots;
>> + u8 reidl_th;
>> + u8 reidl_ex;
>> + u8 reidl_et;
>> + u8 slew;
>> + u8 gain;
>> + u8 baseline_wander;
>> + u8 offset_override;
>> + u8 preq_ratio;
>> + u8 postq_ratio;
>> + u8 adpt_eq;
>> + u8 amp_red;
>> + u8 flt_sel;
>> + bool if20bit;
>> +};
>> +
>> +static const struct lynx_proto_params lynx_proto_params[] = {
>> + [LYNX_PROTO_SGMII] = {
>> + .frate_khz = 5000000,
>> + .rat_sel = LNmGCR0_RAT_SEL_QUARTER,
>> + .if20bit = false,
>> + .prots = LNmGCR0_PROTS_SGMII,
>> + .reidl_th = 0b001,
>> + .reidl_ex = 0b011,
>> + .reidl_et = 0b100,
>> + .slew = 0b01,
>> + .gain = 0b1111,
>> + .offset_override = 0b0011111,
>> + .adpt_eq = 0b110000,
>> + .amp_red = 0b000110,
>> + .flt_sel = 0b111001,
>> + },
>> + [LYNX_PROTO_1000BASEKX] = {
>> + .frate_khz = 5000000,
>> + .rat_sel = LNmGCR0_RAT_SEL_QUARTER,
>> + .if20bit = false,
>> + .prots = LNmGCR0_PROTS_SGMII,
>> + .slew = 0b01,
>> + .gain = 0b1111,
>> + .offset_override = 0b0011111,
>> + .adpt_eq = 0b110000,
>> + .flt_sel = 0b111001,
>> + },
>> + [LYNX_PROTO_SGMII25] = {
>> + .frate_khz = 3125000,
>> + .rat_sel = LNmGCR0_RAT_SEL_SAME,
>> + .if20bit = false,
>> + .prots = LNmGCR0_PROTS_SGMII,
>> + .slew = 0b10,
>> + .offset_override = 0b0011111,
>> + .postq_ratio = 0b00110,
>> + .adpt_eq = 0b110000,
>> + },
>> + [LYNX_PROTO_QSGMII] = {
>> + .frate_khz = 5000000,
>> + .rat_sel = LNmGCR0_RAT_SEL_SAME,
>> + .if20bit = true,
>> + .prots = LNmGCR0_PROTS_SGMII,
>> + .slew = 0b01,
>> + .offset_override = 0b0011111,
>> + .postq_ratio = 0b00110,
>> + .adpt_eq = 0b110000,
>> + .amp_red = 0b000010,
>> + },
>> + [LYNX_PROTO_XFI] = {
>> + .frate_khz = 5156250,
>> + .rat_sel = LNmGCR0_RAT_SEL_DOUBLE,
>> + .if20bit = true,
>> + .prots = LNmGCR0_PROTS_XFI,
>> + .slew = 0b01,
>> + .baseline_wander = LNmRECR0_BASE_WAND_DEFAULT,
>> + .offset_override = 0b1011111,
>> + .postq_ratio = 0b00011,
>> + .adpt_eq = 0b110000,
>> + .amp_red = 0b000111,
>> + },
>> + [LYNX_PROTO_10GKR] = {
>> + .frate_khz = 5156250,
>> + .rat_sel = LNmGCR0_RAT_SEL_DOUBLE,
>> + .if20bit = true,
>> + .prots = LNmGCR0_PROTS_XFI,
>> + .slew = 0b01,
>> + .baseline_wander = LNmRECR0_BASE_WAND_DEFAULT,
>> + .offset_override = 0b1011111,
>> + .preq_ratio = 0b0011,
>> + .postq_ratio = 0b01100,
>> + .adpt_eq = 0b110000,
>> + },
>> +};
>> +
>> +/**
>> + * struct lynx_mode - A single configuration of a protocol controller
>> + * @protos: A bitmask of the &enum lynx_protocol this mode supports
>> + * @pccr: The number of the PCCR which contains this mode
>> + * @idx: The index of the protocol controller. For example, SGMIIB would have
>> + * index 1.
>> + * @cfg: The value to program into the controller to select this mode
>> + *
>> + * The serdes has multiple protocol controllers which can be each be selected
>> + * independently. Depending on their configuration, they may use multiple lanes
>> + * at once (e.g. AUI or PCIe x4). Additionally, multiple protocols may be
>> + * supported by a single mode (XFI and 10GKR differ only in their protocol
>> + * parameters).
>> + */
>> +struct lynx_mode {
>> + u16 protos;
>> + u8 pccr;
>> + u8 idx;
>> + u8 cfg;
>> +};
>> +
>> +static_assert(LYNX_PROTO_LAST - 1 <=
>> + sizeof_field(struct lynx_mode, protos) * BITS_PER_BYTE);
>> +
>> +struct lynx_priv;
>> +
>> +/**
>> + * struct lynx_cfg - Configuration for a particular serdes
>> + * @lanes: Number of lanes
>> + * @endian: Endianness of the registers
>> + * @mode_conflict: Determine whether a protocol controller is already in use
>> + * (by another group).
>> + * @mode_apply: Apply a given protocol. This includes programming the
>> + * appropriate config into the PCCR, as well as enabling/disabling
>> + * any other registers (such as the enabling MDIO access).
>> + * %LYNX_PROTO_NONE may be used to clear any associated registers.
>> + * @mode_init: Finish initializing a mode. All fields are filled in except for
>> + * protos. Type is one of PHY_TYPE_*. mode->protos should be filled
>> + * in, and the other fields should be sanity-checked.
>> + */
>> +struct lynx_cfg {
>> + unsigned int lanes;
>> + enum regmap_endian endian;
>> + bool (*mode_conflict)(struct lynx_priv *serdes,
>> + const struct lynx_mode *mode);
>> + void (*mode_apply)(struct lynx_priv *serdes,
>> + const struct lynx_mode *mode,
>> + enum lynx_protocol proto);
>> + int (*mode_init)(struct lynx_priv *serdes, struct lynx_mode *mode,
>> + int type);
>> +};
>> +
>> +/**
>> + * struct lynx_group - Driver data for a group of lanes
>> + * @serdes: The parent serdes
>> + * @pll: The currently-used pll
>> + * @ex_dly: The ex_dly clock, if used
>> + * @modes: Valid protocol controller configurations
>> + * @mode_count: Number of modes in @modes
>> + * @first_lane: The first lane in the group
>> + * @last_lane: The last lane in the group
>> + * @proto: The currently-configured protocol
>> + * @initialized: Whether the complete state of @modes has been set
>> + * @prots: The protocol set up by the RCW
>> + */
>> +struct lynx_group {
>> + struct lynx_priv *serdes;
>> + struct clk *pll, *ex_dly;
>> + const struct lynx_mode *modes;
>> + size_t mode_count;
>> + unsigned int first_lane;
>> + unsigned int last_lane;
>> + enum lynx_protocol proto;
>> + bool initialized;
>> + u8 prots;
>> +};
>> +
>> +/**
>> + * struct lynx_priv - Driver data for the serdes
>> + * @lock: A lock protecting "common" registers in @regmap, as well as the
>> + * members of this struct. Lane-specific registers are protected by the
>> + * phy's lock. PLL registers are protected by the clock's lock.
>> + * @dev: The serdes device
>> + * @regmap: The backing regmap
>> + * @cfg: SoC-specific configuration
>> + * @plls: The PLLs
>> + * @ex_dlys: The "ex_dly" clocks
>> + * @groups: Groups in the serdes
>> + * @group_count: Number of groups in @groups
>> + * @used_lanes: Bitmap of the lanes currently used by phys
>> + */
>> +struct lynx_priv {
>> + struct mutex lock;
>> + struct device *dev;
>> + struct regmap *regmap;
>> + const struct lynx_cfg *cfg;
>> + struct clk *plls[2], *ex_dlys[2];
>> + struct lynx_group *groups;
>> + unsigned int group_count;
>> + unsigned int used_lanes;
>> +};
>> +
>> +static u32 lynx_read(struct lynx_priv *serdes, u32 reg)
>> +{
>> + unsigned int ret = 0;
>> +
>> + WARN_ON_ONCE(regmap_read(serdes->regmap, reg, &ret));
>> + dev_vdbg(serdes->dev, "%.8x <= %.8x\n", ret, reg);
>> + return ret;
>> +}
>> +
>> +static void lynx_write(struct lynx_priv *serdes, u32 val, u32 reg)
>> +{
>> + dev_vdbg(serdes->dev, "%.8x => %.8x\n", val, reg);
>> + WARN_ON_ONCE(regmap_write(serdes->regmap, reg, val));
>> +}
>> +
>> +/*
>> + * This is tricky. If first_lane=1 and last_lane=0, the condition will see 2,
>> + * 1, 0. But the loop body will see 1, 0. We do this to avoid underflow. We
>> + * can't pull the same trick when incrementing, because then we might have to
>> + * start at -1 if (e.g.) first_lane = 0.
>> + */
>> +#define for_range(val, start, end) \
>> + for (val = start < end ? start : start + 1; \
>> + start < end ? val <= end : val-- > end; \
>> + start < end ? val++ : 0)
>> +#define for_each_lane(lane, group) \
>> + for_range(lane, group->first_lane, group->last_lane)
>> +#define for_each_lane_reverse(lane, group) \
>> + for_range(lane, group->last_lane, group->first_lane)
>> +
>> +static int lynx_power_on(struct phy *phy)
>> +{
>> + int i;
>> + struct lynx_group *group = phy_get_drvdata(phy);
>> + u32 gcr0;
>> +
>> + for_each_lane(i, group) {
>> + gcr0 = lynx_read(group->serdes, LNmGCR0(i));
>> + gcr0 &= ~(LNmGCR0_RX_PD | LNmGCR0_TX_PD);
>> + lynx_write(group->serdes, gcr0, LNmGCR0(i));
>> +
>> + usleep_range(15, 30);
>> + gcr0 |= LNmGCR0_RRST_B | LNmGCR0_TRST_B;
>> + lynx_write(group->serdes, gcr0, LNmGCR0(i));
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static void lynx_power_off_group(struct lynx_group *group)
>> +{
>> + int i;
>> +
>> + for_each_lane_reverse(i, group) {
>> + u32 gcr0 = lynx_read(group->serdes, LNmGCR0(i));
>> +
>> + gcr0 |= LNmGCR0_RX_PD | LNmGCR0_TX_PD;
>> + gcr0 &= ~(LNmGCR0_RRST_B | LNmGCR0_TRST_B);
>> + lynx_write(group->serdes, gcr0, LNmGCR0(i));
>> + }
>> +}
>> +
>> +static int lynx_power_off(struct phy *phy)
>> +{
>> + lynx_power_off_group(phy_get_drvdata(phy));
>> + return 0;
>> +}
>> +
>> +/**
>> + * lynx_lane_bitmap() - Get a bitmap for a group of lanes
>> + * @group: The group of lanes
>> + *
>> + * Return: A mask containing all bits between @group->first and @group->last
>> + */
>> +static unsigned int lynx_lane_bitmap(struct lynx_group *group)
>> +{
>> + if (group->first_lane > group->last_lane)
>> + return GENMASK(group->first_lane, group->last_lane);
>> + else
>> + return GENMASK(group->last_lane, group->first_lane);
>> +}
>> +
>> +/**
>> + * lynx_lookup_mode() - Get the mode for a group/protocol combination
>> + * @group: The group of lanes to use
>> + * @proto: The protocol to use
>> + *
>> + * Return: An appropriate mode to use, or %NULL if none match.
>> + */
>> +static const struct lynx_mode *lynx_lookup_mode(struct lynx_group *group,
>> + enum lynx_protocol proto)
>> +{
>> + int i;
>> +
>> + for (i = 0; i < group->mode_count; i++) {
>> + const struct lynx_mode *mode = &group->modes[i];
>> +
>> + if (BIT(proto) & mode->protos)
>> + return mode;
>> + }
>> +
>> + return NULL;
>> +}
>> +
>> +/**
>> + * lynx_init_late() - Initialize group modes after probe()
>> + * @group: The group of lanes to initialize
>> + *
>> + * Disable all modes for a group, taking care not to disable other groups'
>> + * current modes. This ensures that whenever we select a mode, nothing else is
>> + * interfering. Then, turn off the group.
>> + *
>> + * Return: 0 on success, or -%ENOMEM
>> + */
>> +static int lynx_init_late(struct lynx_group *group)
>> +{
>> + int i, j;
>> + struct lynx_priv *serdes = group->serdes;
>> + const struct lynx_mode **modes;
>> +
>> + modes = kcalloc(serdes->group_count, sizeof(*modes), GFP_KERNEL);
>> + if (!modes)
>> + return -ENOMEM;
>> +
>> + for (i = 0; i < serdes->group_count; i++)
>> + modes[i] = lynx_lookup_mode(&serdes->groups[i],
>> + serdes->groups[i].proto);
>> +
>> + for (i = 0; i < group->mode_count; i++) {
>> + for (j = 0; j < serdes->group_count; j++) {
>> + if (!modes[j])
>> + continue;
>> +
>> + if (group->modes[i].pccr == modes[j]->pccr &&
>> + group->modes[i].idx == modes[j]->idx)
>> + goto skip;
>> + }
>> +
>> + serdes->cfg->mode_apply(serdes, &group->modes[i],
>> + LYNX_PROTO_NONE);
>> +skip: ;
>> + }
>> +
>> + kfree(modes);
>> + lynx_power_off_group(group);
>> + group->initialized = true;
>> + return 0;
>> +}
>> +
>> +static int lynx_init(struct phy *phy)
>> +{
>> + int ret = 0;
>> + struct lynx_group *group = phy_get_drvdata(phy);
>> + struct lynx_priv *serdes = group->serdes;
>> + unsigned int lane_mask = lynx_lane_bitmap(group);
>> +
>> + mutex_lock(&serdes->lock);
>> + if (serdes->used_lanes & lane_mask) {
>> + ret = -EBUSY;
>> + } else {
>> + if (!group->initialized)
>> + ret = lynx_init_late(group);
>> +
>> + if (!ret)
>> + serdes->used_lanes |= lane_mask;
>> + }
>> + mutex_unlock(&serdes->lock);
>> + return ret;
>> +}
>> +
>> +static int lynx_exit(struct phy *phy)
>> +{
>> + struct lynx_group *group = phy_get_drvdata(phy);
>> + struct lynx_priv *serdes = group->serdes;
>> +
>> + clk_disable_unprepare(group->ex_dly);
>> + group->ex_dly = NULL;
>> +
>> + clk_disable_unprepare(group->pll);
>> + clk_rate_exclusive_put(group->pll);
>> + group->pll = NULL;
>> +
>> + mutex_lock(&serdes->lock);
>> + serdes->used_lanes &= ~lynx_lane_bitmap(group);
>> + mutex_unlock(&serdes->lock);
>> + return 0;
>> +}
>> +
>> +/**
>> + * lynx_lookup_proto() - Convert a phy-subsystem mode to a protocol
>> + * @mode: The mode to convert
>> + * @submode: The submode of @mode
>> + *
>> + * Return: A corresponding serdes-specific mode
>> + */
>> +static enum lynx_protocol lynx_lookup_proto(enum phy_mode mode, int submode)
>> +{
>> + switch (mode) {
>> + case PHY_MODE_ETHERNET:
>> + switch (submode) {
>> + case PHY_INTERFACE_MODE_SGMII:
>> + case PHY_INTERFACE_MODE_1000BASEX:
>> + return LYNX_PROTO_SGMII;
>> + case PHY_INTERFACE_MODE_2500BASEX:
>> + return LYNX_PROTO_SGMII25;
>> + case PHY_INTERFACE_MODE_QSGMII:
>> + return LYNX_PROTO_QSGMII;
>> + case PHY_INTERFACE_MODE_XGMII:
>> + case PHY_INTERFACE_MODE_10GBASER:
>> + return LYNX_PROTO_XFI;
>> + case PHY_INTERFACE_MODE_10GKR:
>> + return LYNX_PROTO_10GKR;
>> + default:
>> + return LYNX_PROTO_NONE;
>> + }
>> + default:
>> + return LYNX_PROTO_NONE;
>> + }
>> +}
>> +
>> +static int lynx_validate(struct phy *phy, enum phy_mode phy_mode, int submode,
>> + union phy_configure_opts *opts)
>> +{
>> + enum lynx_protocol proto;
>> + struct lynx_group *group = phy_get_drvdata(phy);
>> + const struct lynx_mode *mode;
>> +
>> + proto = lynx_lookup_proto(phy_mode, submode);
>> + if (proto == LYNX_PROTO_NONE)
>> + return -EINVAL;
>> +
>> + /* Nothing to do */
>> + if (proto == group->proto)
>> + return 0;
>> +
>> + /*
>> + * FIXME: At the moment we don't support switching between major
>> + * protocols. From what I can tell, the serdes is working fine, but
>> + * something goes wrong in the PCS.
>> + */
>> + if (lynx_proto_params[proto].prots != group->prots)
>> + return -EINVAL;
>> +
>> + mode = lynx_lookup_mode(group, proto);
>> + if (!mode)
>> + return -EINVAL;
>> +
>> + return 0;
>> +}
>> +
>> +#define abs_diff(a, b) ({ \
>> + typeof(a) _a = (a); \
>> + typeof(b) _b = (b); \
>> + _a > _b ? _a - _b : _b - _a; \
>> +})
>> +
>> +static int lynx_set_mode(struct phy *phy, enum phy_mode phy_mode, int submode)
>> +{
>> + enum lynx_protocol proto;
>> + const struct lynx_proto_params *params;
>> + const struct lynx_mode *old_mode = NULL, *new_mode;
>> + int i, pll, ret;
>> + struct lynx_group *group = phy_get_drvdata(phy);
>> + struct lynx_priv *serdes = group->serdes;
>> + u32 tmp, teq;
>> + u32 gcr0 = 0, gcr1 = 0, recr0 = 0, tecr0 = 0;
>> + u32 gcr0_mask = 0, gcr1_mask = 0, recr0_mask = 0, tecr0_mask = 0;
>> +
>> + proto = lynx_lookup_proto(phy_mode, submode);
>> + if (proto == LYNX_PROTO_NONE) {
>> + dev_dbg(&phy->dev, "unknown mode/submode %d/%d\n",
>> + phy_mode, submode);
>> + return -EINVAL;
>> + }
>> +
>> + /* Nothing to do */
>> + if (proto == group->proto)
>> + return 0;
>> +
>> + new_mode = lynx_lookup_mode(group, proto);
>> + if (!new_mode) {
>> + dev_dbg(&phy->dev, "could not find mode for %s on lanes %u to %u\n",
>> + lynx_proto_str[proto], group->first_lane,
>> + group->last_lane);
>> + return -EINVAL;
>> + }
>> +
>> + if (group->proto != LYNX_PROTO_NONE) {
>> + old_mode = lynx_lookup_mode(group, group->proto);
>> + if (!old_mode) {
>> + dev_err(&phy->dev, "could not find mode for %s\n",
>> + lynx_proto_str[group->proto]);
>> + return -EBUSY;
>> + }
>> + }
>> +
>> + mutex_lock(&serdes->lock);
>> + if (serdes->cfg->mode_conflict(serdes, new_mode)) {
>> + dev_dbg(&phy->dev, "%s%c already in use\n",
>> + lynx_proto_str[__ffs(new_mode->protos)],
>> + 'A' + new_mode->idx);
>> + ret = -EBUSY;
>> + goto out;
>> + }
>
> what are the cases that you envision to have a mode_conflict?
On the B4860, SGMIIa can be used by either MAC1 or MAC5, depending on the value
of SGMIIA_CFG. Similarly for SGMIIb.
>> +
>> + clk_disable_unprepare(group->ex_dly);
>> + group->ex_dly = NULL;
>> +
>> + clk_disable_unprepare(group->pll);
>> + clk_rate_exclusive_put(group->pll);
>> + group->pll = NULL;
>> +
>> + /* First, try to use a PLL which already has the correct rate */
>> + params = &lynx_proto_params[proto];
>> + for (pll = 0; pll < ARRAY_SIZE(serdes->plls); pll++) {
>> + struct clk *clk = serdes->plls[pll];
>> + unsigned long rate = clk_get_rate(clk);
>> + unsigned long error = abs_diff(rate, params->frate_khz);
>> +
>> + dev_dbg(&phy->dev, "pll%d has rate %lu (error=%lu)\n", pll,
>> + rate, error);
>> + /* Accept up to 100ppm deviation */
>> + if (error && params->frate_khz / error < 10000)
>> + continue;
>> +
>> + if (!clk_set_rate_exclusive(clk, rate))
>> + goto got_pll;
>> + /*
>> + * Someone else got a different rate first (or there was some
>> + * other error)
>> + */
>> + }
>> +
>> + /* If neither PLL has the right rate, try setting it */
>> + for (pll = 0; pll < 2; pll++) {
>> + ret = clk_set_rate_exclusive(serdes->plls[pll],
>> + params->frate_khz);
>> + if (!ret)
>> + goto got_pll;
>> + }
>> +
>> + dev_dbg(&phy->dev, "could not get a pll at %ukHz\n",
>> + params->frate_khz);
>> + goto out;
>> +
>> +got_pll:
>> + group->pll = serdes->plls[pll];
>> + ret = clk_prepare_enable(group->pll);
>> + if (ret)
>> + goto out;
>> +
>> + gcr0_mask |= LNmGCR0_RRAT_SEL | LNmGCR0_TRAT_SEL;
>> + gcr0_mask |= LNmGCR0_RPLL_LES | LNmGCR0_TPLL_LES;
>> + gcr0_mask |= LNmGCR0_RRST_B | LNmGCR0_TRST_B;
>> + gcr0_mask |= LNmGCR0_RX_PD | LNmGCR0_TX_PD;
>> + gcr0_mask |= LNmGCR0_IF20BIT_EN | LNmGCR0_PROTS;
>> + gcr0 |= FIELD_PREP(LNmGCR0_RPLL_LES, !pll);
>> + gcr0 |= FIELD_PREP(LNmGCR0_TPLL_LES, !pll);
>> + gcr0 |= FIELD_PREP(LNmGCR0_RRAT_SEL, params->rat_sel);
>> + gcr0 |= FIELD_PREP(LNmGCR0_TRAT_SEL, params->rat_sel);
>> + gcr0 |= FIELD_PREP(LNmGCR0_IF20BIT_EN, params->if20bit);
>> + gcr0 |= FIELD_PREP(LNmGCR0_PROTS, params->prots);
>> +
>> + gcr1_mask |= LNmGCR1_RDAT_INV | LNmGCR1_TDAT_INV;
>> + gcr1_mask |= LNmGCR1_OPAD_CTL | LNmGCR1_REIDL_TH;
>> + gcr1_mask |= LNmGCR1_REIDL_EX_SEL | LNmGCR1_REIDL_ET_SEL;
>> + gcr1_mask |= LNmGCR1_REIDL_EX_MSB | LNmGCR1_REIDL_ET_MSB;
>> + gcr1_mask |= LNmGCR1_REQ_CTL_SNP | LNmGCR1_REQ_CDR_SNP;
>> + gcr1_mask |= LNmGCR1_TRSTDIR | LNmGCR1_REQ_BIN_SNP;
>> + gcr1_mask |= LNmGCR1_ISLEW_RCTL | LNmGCR1_OSLEW_RCTL;
>> + gcr1 |= FIELD_PREP(LNmGCR1_REIDL_TH, params->reidl_th);
>> + gcr1 |= FIELD_PREP(LNmGCR1_REIDL_EX_SEL, params->reidl_ex & 3);
>> + gcr1 |= FIELD_PREP(LNmGCR1_REIDL_ET_SEL, params->reidl_et & 3);
>> + gcr1 |= FIELD_PREP(LNmGCR1_REIDL_EX_MSB, params->reidl_ex >> 2);
>> + gcr1 |= FIELD_PREP(LNmGCR1_REIDL_ET_MSB, params->reidl_et >> 2);
>> + gcr1 |= FIELD_PREP(LNmGCR1_TRSTDIR,
>> + group->first_lane > group->last_lane);
>> + gcr1 |= FIELD_PREP(LNmGCR1_ISLEW_RCTL, params->slew);
>> + gcr1 |= FIELD_PREP(LNmGCR1_OSLEW_RCTL, params->slew);
>> +
>> + recr0_mask |= LNmRECR0_RXEQ_BST | LNmRECR0_BASE_WAND;
>> + recr0_mask |= LNmRECR0_GK2OVD | LNmRECR0_GK3OVD;
>> + recr0_mask |= LNmRECR0_GK2OVD_EN | LNmRECR0_GK3OVD_EN;
>> + recr0_mask |= LNmRECR0_OSETOVD_EN | LNmRECR0_OSETOVD;
>> + if (params->gain) {
>> + recr0 |= FIELD_PREP(LNmRECR0_GK2OVD, params->gain);
>> + recr0 |= FIELD_PREP(LNmRECR0_GK3OVD, params->gain);
>> + recr0 |= LNmRECR0_GK2OVD_EN | LNmRECR0_GK3OVD_EN;
>> + }
>> + recr0 |= FIELD_PREP(LNmRECR0_BASE_WAND, params->baseline_wander);
>> + recr0 |= FIELD_PREP(LNmRECR0_OSETOVD, params->offset_override);
>> +
>> + tecr0_mask |= LNmTECR0_TEQ_TYPE;
>> + tecr0_mask |= LNmTECR0_SGN_PREQ | LNmTECR0_RATIO_PREQ;
>> + tecr0_mask |= LNmTECR0_SGN_POST1Q | LNmTECR0_RATIO_PST1Q;
>> + tecr0_mask |= LNmTECR0_ADPT_EQ | LNmTECR0_AMP_RED;
>> + teq = LNmTECR0_TEQ_TYPE_NONE;
>> + if (params->postq_ratio) {
>> + teq = LNmTECR0_TEQ_TYPE_POST;
>> + tecr0 |= FIELD_PREP(LNmTECR0_SGN_POST1Q, 1);
>> + tecr0 |= FIELD_PREP(LNmTECR0_RATIO_PST1Q, params->postq_ratio);
>> + }
>> + if (params->preq_ratio) {
>> + teq = LNmTECR0_TEQ_TYPE_BOTH;
>> + tecr0 |= FIELD_PREP(LNmTECR0_SGN_PREQ, 1);
>> + tecr0 |= FIELD_PREP(LNmTECR0_RATIO_PREQ, params->preq_ratio);
>> + }
>> + tecr0 |= FIELD_PREP(LNmTECR0_TEQ_TYPE, teq);
>> + tecr0 |= FIELD_PREP(LNmTECR0_ADPT_EQ, params->adpt_eq);
>> + tecr0 |= FIELD_PREP(LNmTECR0_AMP_RED, params->amp_red);
>> +
>> + for_each_lane(i, group) {
>> + tmp = lynx_read(serdes, LNmGCR0(i));
>> + tmp &= ~(LNmGCR0_RRST_B | LNmGCR0_TRST_B);
>> + lynx_write(serdes, tmp, LNmGCR0(i));
>> + }
>> +
>> + ndelay(50);
>> +
>> + /* Disable the old controller */
>> + if (old_mode)
>> + serdes->cfg->mode_apply(serdes, old_mode, LYNX_PROTO_NONE);
>> +
>> + for_each_lane(i, group) {
>> + tmp = lynx_read(serdes, LNmGCR0(i));
>> + tmp &= ~gcr0_mask;
>> + tmp |= gcr0;
>> + tmp |= FIELD_PREP(LNmGCR0_FIRST_LANE, i == group->first_lane);
>> + lynx_write(serdes, tmp, LNmGCR0(i));
>> +
>> + tmp = lynx_read(serdes, LNmGCR1(i));
>> + tmp &= ~gcr1_mask;
>> + tmp |= gcr1;
>> + lynx_write(serdes, tmp, LNmGCR1(i));
>> +
>> + tmp = lynx_read(serdes, LNmRECR0(i));
>> + tmp &= ~recr0_mask;
>> + tmp |= recr0;
>> + lynx_write(serdes, tmp, LNmRECR0(i));
>> +
>> + tmp = lynx_read(serdes, LNmTECR0(i));
>> + tmp &= ~tecr0_mask;
>> + tmp |= tecr0;
>> + lynx_write(serdes, tmp, LNmTECR0(i));
>> +
>> + tmp = lynx_read(serdes, LNmTTLCR0(i));
>> + tmp &= ~LNmTTLCR0_FLT_SEL;
>> + tmp |= FIELD_PREP(LNmTTLCR0_FLT_SEL, params->flt_sel);
>> + lynx_write(serdes, tmp, LNmTTLCR0(i));
>> + }
>> +
>> + ndelay(120);
>> +
>> + for_each_lane_reverse(i, group) {
>> + tmp = lynx_read(serdes, LNmGCR0(i));
>> + tmp |= LNmGCR0_RRST_B | LNmGCR0_TRST_B;
>> + lynx_write(serdes, tmp, LNmGCR0(i));
>> + }
>> +
>> + /* Enable the new controller */
>> + serdes->cfg->mode_apply(serdes, new_mode, proto);
>> + if (proto == LYNX_PROTO_1000BASEKX) {
>> + group->ex_dly = serdes->ex_dlys[pll];
>> + /* This should never fail since it's from our internal driver */
>> + WARN_ON_ONCE(clk_prepare_enable(group->ex_dly));
>> + }
>> + group->proto = proto;
>> +
>> + dev_dbg(&phy->dev, "set mode to %s on lanes %u to %u\n",
>> + lynx_proto_str[proto], group->first_lane, group->last_lane);
>> +
>> +out:
>> + mutex_unlock(&serdes->lock);
>> + return ret;
>> +}
>> +
>> +static const struct phy_ops lynx_phy_ops = {
>> + .init = lynx_init,
>> + .exit = lynx_exit,
>> + .power_on = lynx_power_on,
>> + .power_off = lynx_power_off,
>> + .set_mode = lynx_set_mode,
>> + .validate = lynx_validate,
>> + .owner = THIS_MODULE,
>> +};
>> +
>> +static int lynx_read_u32(struct device *dev, struct fwnode_handle *fwnode,
>> + const char *prop, u32 *val)
>> +{
>> + int ret;
>> +
>> + ret = fwnode_property_read_u32(fwnode, prop, val);
>> + if (ret)
>> + dev_err(dev, "could not read %s from %pfwP: %d\n", prop,
>> + fwnode, ret);
>> + return ret;
>> +}
>> +
>> +static int lynx_probe_group(struct lynx_priv *serdes, struct lynx_group *group,
>> + struct fwnode_handle *fwnode, bool initialize)
>> +{
>> + int i, lane_count, ret;
>> + struct device *dev = serdes->dev;
>> + struct fwnode_handle *mode_node;
>> + struct lynx_mode *modes;
>> + struct phy *phy;
>> + u32 *lanes = NULL;
>> +
>> + group->serdes = serdes;
>> +
>> + lane_count = fwnode_property_count_u32(fwnode, "reg");
>> + if (lane_count < 0) {
>> + dev_err(dev, "could not read %s from %pfwP: %d\n",
>> + "reg", fwnode, lane_count);
>> + return lane_count;
>> + }
>> +
>> + lanes = kcalloc(lane_count, sizeof(*lanes), GFP_KERNEL);
>> + if (!lanes)
>> + return -ENOMEM;
>> +
>> + ret = fwnode_property_read_u32_array(fwnode, "reg", lanes, lane_count);
>> + if (ret) {
>> + dev_err(dev, "could not read %s from %pfwP: %d\n",
>> + "reg", fwnode, ret);
>> + goto out;
>> + }
>> +
>> + group->first_lane = lanes[0];
>> + group->last_lane = lanes[lane_count - 1];
>> + for (i = 0; i < lane_count; i++) {
>> + u32 prots, gcr0;
>> +
>> + if (lanes[i] > serdes->cfg->lanes) {
>> + ret = -EINVAL;
>> + dev_err(dev, "lane %d not in range 0 to %u\n",
>> + i, serdes->cfg->lanes);
>> + goto out;
>> + }
>> +
>> + if (lanes[i] != group->first_lane +
>> + i * !!(group->last_lane - group->first_lane)) {
>> + ret = -EINVAL;
>> + dev_err(dev, "lane %d is not monotonic\n", i);
>> + goto out;
>> + }
>> +
>> + gcr0 = lynx_read(serdes, LNmGCR0(lanes[i]));
>> + prots = FIELD_GET(LNmGCR0_PROTS, gcr0);
>> + if (i && group->prots != prots) {
>> + ret = -EIO;
>> + dev_err(dev, "lane %d protocol does not match lane 0\n",
>> + lanes[i]);
>> + goto out;
>> + }
>> + group->prots = prots;
>> + }
>> +
>> + fwnode_for_each_child_node(fwnode, mode_node)
>> + group->mode_count++;
>> +
>> + modes = devm_kcalloc(dev, group->mode_count, sizeof(*group->modes),
>> + GFP_KERNEL);
>> + if (!modes) {
>> + ret = -ENOMEM;
>> + goto out;
>> + }
>> +
>> + i = 0;
>> + fwnode_for_each_child_node(fwnode, mode_node) {
>> + struct lynx_mode *mode = &modes[i++];
>> + u32 val;
>> +
>> + ret = lynx_read_u32(dev, mode_node, "fsl,pccr", &val);
>> + if (ret)
>> + goto out;
>> + mode->pccr = val;
>> +
>> + ret = lynx_read_u32(dev, mode_node, "fsl,index", &val);
>> + if (ret)
>> + goto out;
>> + mode->idx = val;
>> +
>> + ret = lynx_read_u32(dev, mode_node, "fsl,cfg", &val);
>> + if (ret)
>> + goto out;
>> + mode->cfg = val;
>> +
>> + ret = lynx_read_u32(dev, mode_node, "fsl,type", &val);
>> + if (ret)
>> + goto out;
>> +
>> + ret = serdes->cfg->mode_init(serdes, mode, val);
>> + if (ret)
>> + goto out;
>> +
>> + dev_dbg(dev, "mode PCCR%X.%s%c_CFG=%x on lanes %u to %u\n",
>> + mode->pccr, lynx_proto_str[__ffs(mode->protos)],
>> + 'A' + mode->idx, mode->cfg, group->first_lane,
>> + group->last_lane);
>> + }
>> +
>> + WARN_ON(i != group->mode_count);
>> + group->modes = modes;
>> +
>> + if (initialize) {
>> + /* Deselect anything configured by the RCW/bootloader */
>> + for (i = 0; i < group->mode_count; i++)
>> + serdes->cfg->mode_apply(serdes, &group->modes[i],
>> + LYNX_PROTO_NONE);
>> +
>> + /* Disable the lanes for now */
>> + lynx_power_off_group(group);
>> + group->initialized = true;
>> + }
>> +
>> + phy = devm_phy_create(dev, to_of_node(fwnode), &lynx_phy_ops);
>> + ret = PTR_ERR_OR_ZERO(phy);
>> + if (ret)
>> + dev_err_probe(dev, ret, "could not create phy\n");
>> + else
>> + phy_set_drvdata(phy, group);
>> +
>> +out:
>> + kfree(lanes);
>> + return ret;
>> +}
>> +
>> +static int lynx_probe(struct platform_device *pdev)
>> +{
>> + bool compat;
>> + int ret, i = 0;
>> + struct device *dev = &pdev->dev;
>> + struct fwnode_handle *group_node;
>> + struct lynx_priv *serdes;
>> + struct phy_provider *provider;
>> + struct regmap_config regmap_config = {
>> + .reg_bits = 32,
>> + .reg_stride = 4,
>> + .val_bits = 32,
>> + .disable_locking = true,
>> + };
>> + struct resource *res;
>> + void __iomem *base;
>> +
>> + serdes = devm_kzalloc(dev, sizeof(*serdes), GFP_KERNEL);
>> + if (!serdes)
>> + return -ENOMEM;
>> +
>> + serdes->dev = dev;
>> + platform_set_drvdata(pdev, serdes);
>> + mutex_init(&serdes->lock);
>> + serdes->cfg = device_get_match_data(dev);
>> +
>> + base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
>> + if (IS_ERR(base)) {
>> + ret = PTR_ERR(base);
>> + dev_err_probe(dev, ret, "could not get/map registers\n");
>> + return ret;
>> + }
>> +
>> + regmap_config.val_format_endian = serdes->cfg->endian;
>> + regmap_config.max_register = res->end - res->start;
>> + serdes->regmap = devm_regmap_init_mmio(dev, base, ®map_config);
>> + if (IS_ERR(serdes->regmap)) {
>> + ret = PTR_ERR(serdes->regmap);
>> + dev_err_probe(dev, ret, "could not create regmap\n");
>> + return ret;
>> + }
>> +
>> + compat = device_property_present(dev, "fsl,unused-lanes-reserved");
>> + ret = lynx_clks_init(dev, serdes->regmap, serdes->plls,
>> + serdes->ex_dlys, compat);
>> + if (ret)
>> + return ret;
>> +
>> + serdes->group_count = device_get_child_node_count(dev);
>> + serdes->groups = devm_kcalloc(dev, serdes->group_count,
>> + sizeof(*serdes->groups), GFP_KERNEL);
>> + if (!serdes->groups)
>> + return -ENOMEM;
>> +
>> + device_for_each_child_node(dev, group_node) {
>> + ret = lynx_probe_group(serdes, &serdes->groups[i++],
>> + group_node, !compat);
>> + if (ret)
>> + return ret;
>> + }
>> + WARN_ON(i != serdes->group_count);
>> +
>> + provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
>> + ret = PTR_ERR_OR_ZERO(provider);
>> + if (ret)
>> + dev_err_probe(dev, ret, "could not register phy provider\n");
>> + else
>> + dev_info(dev, "probed with %u lanes and %u groups\n",
>> + serdes->cfg->lanes, serdes->group_count);
>> + return ret;
>> +}
>> +
>> +/*
>> + * These are common helpers for the PCCRs found on (most) Layerscape SoCs.
>> + * There is an earlier layout used on most T-series SoCs, as well as the
>> + * LS1020A/21A/22A.
>> + */
>> +
>> +static int lynx_ls_pccr_params(const struct lynx_mode *mode, u32 *off,
>> + u32 *shift, u32 *mask)
>> +{
>> + if (mode->protos & PROTO_MASK(SGMII)) {
>> + *off = LS_PCCRa(0x8);
>> + *mask = PCCR8_SGMIIa_MASK;
>> + *shift = PCCR8_SGMIIa_SHIFT(mode->idx);
>> + } else if (mode->protos & PROTO_MASK(QSGMII)) {
>> + *off = LS_PCCRa(0x9);
>> + *mask = PCCR9_QSGMIIa_MASK;
>> + *shift = PCCR9_QSGMIIa_SHIFT(mode->idx);
>> + } else if (mode->protos & PROTO_MASK(XFI)) {
>> + *off = LS_PCCRa(0xB);
>> + *mask = PCCRB_XFIa_MASK;
>> + *shift = PCCRB_XFIa_SHIFT(mode->idx);
>> + } else {
>> + return -EINVAL;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static bool lynx_ls_mode_conflict(struct lynx_priv *serdes,
>> + const struct lynx_mode *mode)
>> +{
>> + u32 off, shift, mask;
>> +
>> + if (WARN_ON_ONCE(lynx_ls_pccr_params(mode, &off, &shift, &mask)))
>> + return true;
>> +
>> + return (lynx_read(serdes, off) >> shift) & mask;
>> +}
>> +
>> +static void lynx_ls_mode_apply(struct lynx_priv *serdes,
>> + const struct lynx_mode *mode,
>> + enum lynx_protocol proto)
>> +{
>> + u32 pccr, off, shift, mask;
>> +
>> + if (WARN_ON_ONCE(proto != LYNX_PROTO_NONE &&
>> + !(mode->protos & BIT(proto))))
>> + return;
>> + if (WARN_ON_ONCE(lynx_ls_pccr_params(mode, &off, &shift, &mask)))
>> + return;
>> +
>> + dev_dbg(serdes->dev, "applying %s to PCCR%X.%s%c_CFG\n",
>> + lynx_proto_str[proto], mode->pccr,
>> + lynx_proto_str[__ffs(mode->protos)], 'A' + mode->idx);
>> +
>> + pccr = lynx_read(serdes, off);
>> + pccr &= ~(mask << shift);
>> + if (proto != LYNX_PROTO_NONE)
>> + pccr |= mode->cfg << shift;
>> +
>> + if (proto == LYNX_PROTO_1000BASEKX)
>> + pccr |= PCCR8_SGMIIa_KX << shift;
>> + lynx_write(serdes, pccr, off);
>> +
>> + if (mode->protos & PROTO_MASK(SGMII)) {
>> + u32 cr1 = lynx_read(serdes, LS_SGMIIaCR1(mode->idx));
>> +
>> + cr1 &= ~SGMIIaCR1_SGPCS_EN;
>> + cr1 |= proto == LYNX_PROTO_NONE ? 0 : SGMIIaCR1_SGPCS_EN;
>> + lynx_write(serdes, cr1, LS_SGMIIaCR1(mode->idx));
>> + }
>> +}
>> +
>> +static int lynx_ls_mode_init(struct lynx_priv *serdes, struct lynx_mode *mode,
>> + int type)
>> +{
>> + u32 max = 0, off, shift, mask;
>> +
>> + if (mode->pccr >= 0x10) {
>> + dev_err(serdes->dev, "PCCR index %u too large\n", mode->pccr);
>> + return -EINVAL;
>> + }
>> +
>> + switch (type) {
>> + case PHY_TYPE_2500BASEX:
>> + mode->protos = PROTO_MASK(SGMII25);
>> + fallthrough;
>> + case PHY_TYPE_SGMII:
>> + max = 8;
>> + mode->protos |= PROTO_MASK(SGMII) | PROTO_MASK(1000BASEKX);
>> + break;
>> + case PHY_TYPE_QSGMII:
>> + max = 4;
>> + mode->protos = PROTO_MASK(QSGMII);
>> + break;
>> + case PHY_TYPE_10GBASER:
>> + max = 8;
>> + mode->protos = PROTO_MASK(XFI) | PROTO_MASK(10GKR);
>> + break;
>> + default:
>> + dev_err(serdes->dev, "unknown mode type %d\n", type);
>> + return -EINVAL;
>> + }
>> +
>> + if (mode->idx >= max) {
>> + dev_err(serdes->dev, "%s index %u too large\n",
>> + lynx_proto_str[__ffs(mode->protos)], mode->idx);
>> + return -EINVAL;
>> + }
>> +
>> + if (WARN_ON_ONCE(lynx_ls_pccr_params(mode, &off, &shift, &mask)))
>> + return -EINVAL;
>> +
>> + if (!mode->cfg || mode->cfg & ~mask) {
>> + dev_err(serdes->dev, "bad value %x for %s%c_CFG\n",
>> + mode->cfg, lynx_proto_str[__ffs(mode->protos)],
>> + 'A' + mode->idx);
>> + return -EINVAL;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static const struct lynx_cfg ls1046a_cfg = {
>> + .lanes = 4,
>> + .endian = REGMAP_ENDIAN_BIG,
>> + .mode_conflict = lynx_ls_mode_conflict,
>> + .mode_apply = lynx_ls_mode_apply,
>> + .mode_init = lynx_ls_mode_init,
>> +};
>> +
>> +static const struct lynx_cfg ls1088a_cfg = {
>> + .lanes = 4,
>> + .endian = REGMAP_ENDIAN_LITTLE,
>> + .mode_conflict = lynx_ls_mode_conflict,
>> + .mode_apply = lynx_ls_mode_apply,
>> + .mode_init = lynx_ls_mode_init,
>
> So you have cfg with mode_xxx pointing to same functions for both of the
> versions you support... so question is why do this and not call the
> functions directly?
The intention is to make it easy to add support for T-series processors,
which have a different PCCR layout.
>> +};
>> +
>> +static const struct of_device_id lynx_of_match[] = {
>> + { .compatible = "fsl,ls1046a-serdes", .data = &ls1046a_cfg },
>> + { .compatible = "fsl,ls1088a-serdes", .data = &ls1088a_cfg },
>> + { },
>> +};
>> +MODULE_DEVICE_TABLE(of, lynx_of_match);
>> +
>> +static struct platform_driver lynx_driver = {
>> + .probe = lynx_probe,
>> + .driver = {
>> + .name = "lynx_10g",
>> + .of_match_table = lynx_of_match,
>> + },
>> +};
>> +module_platform_driver(lynx_driver);
>> +
>> +MODULE_AUTHOR("Sean Anderson <sean.anderson@xxxxxxxx>");
>> +MODULE_DESCRIPTION("Lynx 10G SerDes driver");
>> +MODULE_LICENSE("GPL");
>> --
>> 2.35.1.1320.gc452695387.dirty
>
--Sean
