Support sending control reports to Aquacomputer Aquaero. This commit only
enables control of the temperature offset as this works in the same manner as
with already supported devices.
Also, mention temperature offset control for Aquaero in docs.
Signed-off-by: Leonard Anderweit <leonard.anderweit@xxxxxxxxx>
---
Documentation/hwmon/aquacomputer_d5next.rst | 4 +-
drivers/hwmon/aquacomputer_d5next.c | 62 ++++++++++++++++-----
2 files changed, 50 insertions(+), 16 deletions(-)
diff --git a/Documentation/hwmon/aquacomputer_d5next.rst b/Documentation/hwmon/aquacomputer_d5next.rst
index 7d0d015b1a52..de43374940b8 100644
--- a/Documentation/hwmon/aquacomputer_d5next.rst
+++ b/Documentation/hwmon/aquacomputer_d5next.rst
@@ -25,7 +25,7 @@ communicate through proprietary USB HID protocols.
The Aquaero devices expose eight physical, eight virtual and four calculated
virtual temperature sensors, as well as two flow sensors. The fans expose their
-speed (in RPM), power, voltage and current.
+speed (in RPM), power, voltage and current. The temperature offset can be controlled.
For the D5 Next pump, available sensors are pump and fan speed, power, voltage
and current, as well as coolant temperature and eight virtual temp sensors. Also
@@ -75,7 +75,7 @@ Sysfs entries
================ ==============================================================
temp[1-20]_input Physical/virtual temperature sensors (in millidegrees Celsius)
-temp[1-4]_offset Temperature sensor correction offset (in millidegrees Celsius)
+temp[1-8]_offset Temperature sensor correction offset (in millidegrees Celsius)
fan[1-8]_input Pump/fan speed (in RPM) / Flow speed (in dL/h)
fan5_pulses Quadro flow sensor pulses
power[1-8]_input Pump/fan power (in micro Watts)
diff --git a/drivers/hwmon/aquacomputer_d5next.c b/drivers/hwmon/aquacomputer_d5next.c
index 03ef9e0258d2..95461e2907e1 100644
--- a/drivers/hwmon/aquacomputer_d5next.c
+++ b/drivers/hwmon/aquacomputer_d5next.c
@@ -56,6 +56,7 @@ static const char *const aqc_device_names[] = {
#define SERIAL_PART_OFFSET 2
#define CTRL_REPORT_ID 0x03
+#define AQUAERO_CTRL_REPORT_ID 0x0b
/* The HID report that the official software always sends
* after writing values, currently same for all devices
@@ -67,6 +68,14 @@ static u8 secondary_ctrl_report[] = {
0x02, 0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x34, 0xC6
};
+/* Secondary HID report values for Aquaero */
+#define AQUAERO_SECONDARY_CTRL_REPORT_ID 0x06
+#define AQUAERO_SECONDARY_CTRL_REPORT_SIZE 0x07
+
+static u8 aquaero_secondary_ctrl_report[] = {
+ 0x06, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00
+};
+
/* Report IDs for legacy devices */
#define POWERADJUST3_STATUS_REPORT_ID 0x03
@@ -94,6 +103,7 @@ static u8 secondary_ctrl_report[] = {
#define AQUAERO_NUM_VIRTUAL_SENSORS 8
#define AQUAERO_NUM_CALC_VIRTUAL_SENSORS 4
#define AQUAERO_NUM_FLOW_SENSORS 2
+#define AQUAERO_CTRL_REPORT_SIZE 0xa93
/* Sensor report offsets for Aquaero fan controllers */
#define AQUAERO_SENSOR_START 0x65
@@ -106,6 +116,9 @@ static u8 secondary_ctrl_report[] = {
#define AQUAERO_FAN_SPEED_OFFSET 0x00
static u16 aquaero_sensor_fan_offsets[] = { 0x167, 0x173, 0x17f, 0x18B };
+/* Control report offsets for the Aquaero fan controllers */
+#define AQUAERO_TEMP_CTRL_OFFSET 0xdb
+
/* Specs of the D5 Next pump */
#define D5NEXT_NUM_FANS 2
#define D5NEXT_NUM_SENSORS 1
@@ -441,6 +454,10 @@ struct aqc_data {
const char *name;
int status_report_id; /* Used for legacy devices, report is stored in buffer */
+ int ctrl_report_id;
+ int secondary_ctrl_report_id;
+ int secondary_ctrl_report_size;
+ u8 *secondary_ctrl_report;
int buffer_size;
u8 *buffer;
@@ -513,7 +530,7 @@ static int aqc_get_ctrl_data(struct aqc_data *priv)
int ret;
memset(priv->buffer, 0x00, priv->buffer_size);
- ret = hid_hw_raw_request(priv->hdev, CTRL_REPORT_ID, priv->buffer, priv->buffer_size,
+ ret = hid_hw_raw_request(priv->hdev, priv->ctrl_report_id, priv->buffer, priv->buffer_size,
HID_FEATURE_REPORT, HID_REQ_GET_REPORT);
if (ret < 0)
ret = -ENODATA;
@@ -527,23 +544,27 @@ static int aqc_send_ctrl_data(struct aqc_data *priv)
int ret;
u16 checksum;
- /* Init and xorout value for CRC-16/USB is 0xffff */
- checksum = crc16(0xffff, priv->buffer + priv->checksum_start, priv->checksum_length);
- checksum ^= 0xffff;
+ /* Checksum is not needed for Aquaero */
+ if (priv->kind != aquaero) {
+ /* Init and xorout value for CRC-16/USB is 0xffff */
+ checksum = crc16(0xffff, priv->buffer + priv->checksum_start,
+ priv->checksum_length);
+ checksum ^= 0xffff;
- /* Place the new checksum at the end of the report */
- put_unaligned_be16(checksum, priv->buffer + priv->checksum_offset);
+ /* Place the new checksum at the end of the report */
+ put_unaligned_be16(checksum, priv->buffer + priv->checksum_offset);
+ }
/* Send the patched up report back to the device */
- ret = hid_hw_raw_request(priv->hdev, CTRL_REPORT_ID, priv->buffer, priv->buffer_size,
+ ret = hid_hw_raw_request(priv->hdev, priv->ctrl_report_id, priv->buffer, priv->buffer_size,
HID_FEATURE_REPORT, HID_REQ_SET_REPORT);
if (ret < 0)
return ret;
/* The official software sends this report after every change, so do it here as well */
- ret = hid_hw_raw_request(priv->hdev, SECONDARY_CTRL_REPORT_ID, secondary_ctrl_report,
- SECONDARY_CTRL_REPORT_SIZE, HID_FEATURE_REPORT,
- HID_REQ_SET_REPORT);
+ ret = hid_hw_raw_request(priv->hdev, priv->secondary_ctrl_report_id,
+ priv->secondary_ctrl_report, priv->secondary_ctrl_report_size,
+ HID_FEATURE_REPORT, HID_REQ_SET_REPORT);
return ret;
}
@@ -969,10 +990,10 @@ static const struct hwmon_channel_info *aqc_info[] = {
HWMON_T_INPUT | HWMON_T_LABEL | HWMON_T_OFFSET,
HWMON_T_INPUT | HWMON_T_LABEL | HWMON_T_OFFSET,
HWMON_T_INPUT | HWMON_T_LABEL | HWMON_T_OFFSET,
- HWMON_T_INPUT | HWMON_T_LABEL,
- HWMON_T_INPUT | HWMON_T_LABEL,
- HWMON_T_INPUT | HWMON_T_LABEL,
- HWMON_T_INPUT | HWMON_T_LABEL,
+ HWMON_T_INPUT | HWMON_T_LABEL | HWMON_T_OFFSET,
+ HWMON_T_INPUT | HWMON_T_LABEL | HWMON_T_OFFSET,
+ HWMON_T_INPUT | HWMON_T_LABEL | HWMON_T_OFFSET,
+ HWMON_T_INPUT | HWMON_T_LABEL | HWMON_T_OFFSET,
HWMON_T_INPUT | HWMON_T_LABEL,
HWMON_T_INPUT | HWMON_T_LABEL,
HWMON_T_INPUT | HWMON_T_LABEL,
@@ -1275,6 +1296,9 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
priv->num_flow_sensors = AQUAERO_NUM_FLOW_SENSORS;
priv->flow_sensors_start_offset = AQUAERO_FLOW_SENSORS_START;
+ priv->buffer_size = AQUAERO_CTRL_REPORT_SIZE;
+ priv->temp_ctrl_offset = AQUAERO_TEMP_CTRL_OFFSET;
+
priv->temp_label = label_temp_sensors;
priv->virtual_temp_label = label_virtual_temp_sensors;
priv->calc_virt_temp_label = label_aquaero_calc_temp_sensors;
@@ -1438,6 +1462,11 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
priv->firmware_version_offset = AQUAERO_FIRMWARE_VERSION;
priv->fan_structure = &aqc_aquaero_fan_structure;
+
+ priv->ctrl_report_id = AQUAERO_CTRL_REPORT_ID;
+ priv->secondary_ctrl_report_id = AQUAERO_SECONDARY_CTRL_REPORT_ID;
+ priv->secondary_ctrl_report_size = AQUAERO_SECONDARY_CTRL_REPORT_SIZE;
+ priv->secondary_ctrl_report = aquaero_secondary_ctrl_report;
break;
case poweradjust3:
priv->status_report_id = POWERADJUST3_STATUS_REPORT_ID;
@@ -1446,6 +1475,11 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
priv->serial_number_start_offset = AQC_SERIAL_START;
priv->firmware_version_offset = AQC_FIRMWARE_VERSION;
+ priv->ctrl_report_id = CTRL_REPORT_ID;
+ priv->secondary_ctrl_report_id = SECONDARY_CTRL_REPORT_ID;
+ priv->secondary_ctrl_report_size = SECONDARY_CTRL_REPORT_SIZE;
+ priv->secondary_ctrl_report = secondary_ctrl_report;
+
if (priv->kind == aquastreamult)
priv->fan_structure = &aqc_aquastreamult_fan_structure;
else
--
2.39.1
