Correct spelling problems for Documentation/spi/ as reported
by codespell.
Signed-off-by: Randy Dunlap <rdunlap@xxxxxxxxxxxxx>
Cc: Mark Brown <broonie@xxxxxxxxxx>
Cc: linux-spi@xxxxxxxxxxxxxxx
Cc: Jonathan Corbet <corbet@xxxxxxx>
Cc: linux-doc@xxxxxxxxxxxxxxx
---
Documentation/spi/pxa2xx.rst | 12 ++++++------
Documentation/spi/spi-lm70llp.rst | 2 +-
Documentation/spi/spi-summary.rst | 2 +-
3 files changed, 8 insertions(+), 8 deletions(-)
diff -- a/Documentation/spi/pxa2xx.rst b/Documentation/spi/pxa2xx.rst
--- a/Documentation/spi/pxa2xx.rst
+++ b/Documentation/spi/pxa2xx.rst
@@ -141,15 +141,15 @@ field. Below is a sample configuration u
::
static struct pxa2xx_spi_chip cs8415a_chip_info = {
- .tx_threshold = 8, /* SSP hardward FIFO threshold */
- .rx_threshold = 8, /* SSP hardward FIFO threshold */
+ .tx_threshold = 8, /* SSP hardware FIFO threshold */
+ .rx_threshold = 8, /* SSP hardware FIFO threshold */
.dma_burst_size = 8, /* Byte wide transfers used so 8 byte bursts */
.timeout = 235, /* See Intel documentation */
};
static struct pxa2xx_spi_chip cs8405a_chip_info = {
- .tx_threshold = 8, /* SSP hardward FIFO threshold */
- .rx_threshold = 8, /* SSP hardward FIFO threshold */
+ .tx_threshold = 8, /* SSP hardware FIFO threshold */
+ .rx_threshold = 8, /* SSP hardware FIFO threshold */
.dma_burst_size = 8, /* Byte wide transfers used so 8 byte bursts */
.timeout = 235, /* See Intel documentation */
};
@@ -157,7 +157,7 @@ field. Below is a sample configuration u
static struct spi_board_info streetracer_spi_board_info[] __initdata = {
{
.modalias = "cs8415a", /* Name of spi_driver for this device */
- .max_speed_hz = 3686400, /* Run SSP as fast a possbile */
+ .max_speed_hz = 3686400, /* Run SSP as fast a possible */
.bus_num = 2, /* Framework bus number */
.chip_select = 0, /* Framework chip select */
.platform_data = NULL; /* No spi_driver specific config */
@@ -166,7 +166,7 @@ field. Below is a sample configuration u
},
{
.modalias = "cs8405a", /* Name of spi_driver for this device */
- .max_speed_hz = 3686400, /* Run SSP as fast a possbile */
+ .max_speed_hz = 3686400, /* Run SSP as fast a possible */
.bus_num = 2, /* Framework bus number */
.chip_select = 1, /* Framework chip select */
.controller_data = &cs8405a_chip_info, /* Master chip config */
diff -- a/Documentation/spi/spi-lm70llp.rst b/Documentation/spi/spi-lm70llp.rst
--- a/Documentation/spi/spi-lm70llp.rst
+++ b/Documentation/spi/spi-lm70llp.rst
@@ -57,7 +57,7 @@ devices might share the same SI/SO pin.
The bitbanger routine in this driver (lm70_txrx) is called back from
the bound "hwmon/lm70" protocol driver through its sysfs hook, using a
spi_write_then_read() call. It performs Mode 0 (SPI/Microwire) bitbanging.
-The lm70 driver then inteprets the resulting digital temperature value
+The lm70 driver then interprets the resulting digital temperature value
and exports it through sysfs.
A "gotcha": National Semiconductor's LM70 LLP eval board circuit schematic
diff -- a/Documentation/spi/spi-summary.rst b/Documentation/spi/spi-summary.rst
--- a/Documentation/spi/spi-summary.rst
+++ b/Documentation/spi/spi-summary.rst
@@ -105,7 +105,7 @@ find isn't necessarily helpful. The fou
- CPHA indicates the clock phase used to sample data; CPHA=0 says
sample on the leading edge, CPHA=1 means the trailing edge.
- Since the signal needs to stablize before it's sampled, CPHA=0
+ Since the signal needs to stabilize before it's sampled, CPHA=0
implies that its data is written half a clock before the first
clock edge. The chipselect may have made it become available.
