Re: [PATCH] Documentation: dt: bindings: TI WiLink modules

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 06/27/2013 01:51 PM, Luciano Coelho wrote:
On Thu, 2013-06-27 at 08:39 -0500, Nishanth Menon wrote:
On Thu, Jun 27, 2013 at 8:30 AM, Luciano Coelho <coelho@xxxxxx> wrote:
On Thu, 2013-06-27 at 08:23 -0500, Nishanth Menon wrote:
On 06/27/2013 08:19 AM, Luciano Coelho wrote:
On Thu, 2013-06-27 at 08:15 -0500, Nishanth Menon wrote:
On Thu, Jun 27, 2013 at 7:58 AM, Luciano Coelho <coelho@xxxxxx> wrote:
For the actual DTS files, I could add a wilink.dtsi with enumerations
for these values so they could be used in the node definitions.  But I'm
not sure it's going to be that valuable in the end.
The  way GPIO HIGH was defined might help to provide guidance I think :)

Where? As far as I can see, the GPIO flags are defined in a bitmap.

include/dt-bindings/gpio/gpio.h

Thanks! I don't see these macros used anywhere, though.
umm... I'd think you have'nt looked deep enough / lists :)

If you mean mailing lists, you're right, I didn't.  I just did a git
grep for the macros and didn't find any users.
git grep "GPIO_ACTIVE_[HIGH|LOW]" arch/arm/boot/dts/|wc -l
344
on next-20130626. anyways, besides the point.


This seems to be a completely different thing.  This is the header that
contains the helper functions to get GPIO-related device tree nodes,
isn't it?
That is true, but it also contains the flag for level which needs to
be in sync with the gpio.h dts header.
just a hint. not saying frequencies were defined in header. for systems
that define frequencies - example cpufreq OPPs, clock node usage, we do
not use indexing to frequency, instead, that is the responsibility of
driver to convert frequency back to required index.
git grep frequency Documentation/devicetree/bindings gives you how the
precedence looks like.

Personally, if given a choice, I'd go with actual frequencies rather
than indexes.

If I do that, I need to add also a separate flag to define whether the
XTAL clock is used or not.  For instance, we have 26MHz and 26MHz
crystal; and 38.4MHz and 38.4MHz crystal...
Yes, you would have to. at the same time, it is easy for module maker
to provide dtsi corresponding to exact h/w representation on his
module using wilink chip without being worried about weird index value
whose meaning is hidden in binding

The module makers need to know about the bindings and read the document
before they specify the node in DTS.  I think for clarity, a comment in
the DTS file stating the actual frequency is good enough.  Simpler and
more efficient (in terms of DT binary size and module code size) than
adding the actual frequencies.


On the flip side, It also allows driver to reject frequencies /
configurations that are not supported by the corresponding chip.

It's actually much easier to reject frequencies that are not valid with
the enumeration.  "if (refclock > 5) { bail_out(); }".  If I need to
check every frequency, I need to add an array of valid frequencies and
so on.  Waste of code, IMHO.


As I said, just my 2 cents. Personally, I'd like dts files to be as
readable as c files without having to dig through bindings document.

As I said before, for readability, adding a comment with the frequency
is good enough.  This is what I did for PandaES's DTS (not sent out
yet):

	wlan {
	     compatible = "ti,wilink6";
	     interrupt-parent = <&gpio2>;
	     interrupts = <21 0x4>;	/* gpio line 53, high level triggered */
	     refclock = <2>;		/* 38.4 MHz */
	 };

Looks more readable to me than:

	wlan {
	     compatible = "ti,wilink6";
	     interrupt-parent = <&gpio2>;
	     interrupts = <21 0x4>;	/* gpio line 53, high level triggered */
	     refclock = <38400>;
	     refclock_xtal = <0>;
	 };

The macro idea sounds better to me, but in this case this code is so
simple that I don't think it's really worth it.

And, from another point of view, I see this as only a specification of
the module's details.  The frequency value is not really used anywhere
outside the module, so we don't see it.  I don't think there's a good
reason to expose the actual frequency to the kernel (and parse it back
to the values the firmware needs), since nothing else inside the kernel
will care about it.
Overview: we are adding bindings for Documentation/devicetree/bindings/net/wireless/ti-wilink.txt Which I believe is intended to be generic.

Current frequencies supported for tcxoclock is the following for WiLink7
+	0 = 19.200 MHz
+	1 = 26.000 MHz
+	2 = 38.400 MHz
+	3 = 52.000 MHz
+	4 = 16.368 MHz
+	5 = 32.736 MHz
+	6 = 16.800 MHz
+	7 = 33.600 MHz
Say wilink9 comes along and redefines this map OR introduces support for 20MHz support making the map 0-8, you'd no longer be able to support this map. or say a new update of firmware magically changes this mapping or something unexpected.

If the translation and validation is done in the driver, it is trivial to handle without redefining the binding and breaking older dtbs (if relevant)

Indexes to another entity is always a maintenance burden in the longer run and needs judicious control. If it is possible to avoid it by selecting the right parameters, I am a hard advocate for the same.

--
Regards,
Nishanth Menon
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux