On 06/20/2013 05:57 AM, Christian Ruppert wrote:
> Hello Stephen,
>
> On Wed, Jun 19, 2013 at 12:27:56PM -0600, Stephen Warren wrote:
>> On 06/19/2013 12:10 PM, Stephen Warren wrote:
>>> On 06/14/2013 03:12 AM, Christian Ruppert wrote:
>>>> On Thu, Jun 13, 2013 at 03:38:09PM -0600, Stephen Warren wrote:
>>>>> On 06/13/2013 06:55 AM, Christian Ruppert wrote:
>> [...]
>>>>> The potential advantage of this patch is that the pinctrl-side of the
>>>>> mapping can be a group name rather than pin IDs, which might reduce the
>>>>> size of the mapping list if you have an extremely sparse or non-linear
>>>>> mapping /and/ parts of that mapping just happen to align with the pin
>>>>> groups in the pin controller HW, since each entry in the gpio-ranges
>>>>> property can be sparse/non-linear, rather than being a small linear
>>>>> chunk of the mapping.
>>>>
>>>> Pin controller authors have the freedom to define pin groups just for
>>>> the purpose of "predefining" the pinctrl side of GPIO ranges.
>>>
>>> Hmm. I suppose that's true. I'm not sure how enthusiastic I am about
>>> doing this though... The reason I'm unsure is because it starts using
>>> pin groups from something other than groups of pins in HW that are all
>>> affected by the same mux or config bits in a register, and starts using
>>> pin groups for something else; GPIO<->pinmux pins mapping. Perhaps it's
>>> OK though, considering the other abuses of pin groups that are already
>>> present, such as using pin groups to represent default/common uses of
>>> groups of pins that don't actually exist in HW.
>
> The reason for these "abuses" might just be that every company (or maybe
> even hardware team) has a different understanding of how pin muxing
> should be implemented in hardware. There are probably as many different
> pin muxing architectures out there as companies (maybe even more).
> Finding a "one size fits all"-approach to this is extremely difficult
> and driver authors adapt the kernel infrastructure as well as they can
> to the hardware they have. As an example, see below for a fundamental
> cultural difference between your hardware/integration team and ours.
The issues I'm talking about are more SW issues; people have created
"pin groups" that represent both a set of pins/groups *and* the function
the is muxed onto them (and perhaps pin config settings too), rather
than having the driver create "pin groups" that actually represent just
groups of pins, and then using the DT pinctrl bindings as intended to
select which mux/config settings to use for that group.
>> I've realized what I don't like about this.
>>
>> Pin groups are supposed to be something that represents some property of
>> the pinctrl HW itself. So, if you have register "X" bits 3-0 that define
>> the mux function for pins 8, 9, 10, and 11, then there really is a pin
>> group that exists in HW, and that pin group will still exist with that
>> same definition no matter what SoC you put the pinctrl HW into. If this
>> changes, it's not the same pinctrl HW module.
>
> Let me see if I get this right (Let's take the example in the section
> "What is pinmuxing" of Documentation/pinctrl.txt in Linux-3.10-rc6 which
> is similar to TB10x):
> If I understand you correctly, you define two pin groups in this
> example:
> gpr1 = {A5, A6, A7, A8, B5};
> grp2 = {A1, B1, C1, D1, E1, F1, G1, G2, G3, G4, H1};
>
> grp1 has three configurations: allgpio, i2c and spi
> grp2 has five configurations: allgpio, mmc2, mmc2_spi, mmc4, mmc4_spi, mmc8
No, I don't think so at all.
When I pushed for the concept of groups, I intended it to mean precisely
one single thing. The points below describe this.
1) A pin is a single pin/ball/pad on the package.
2) Some register fields affect just a single pin. For example, there may
be a register field that affects pin A8's mux setting only.
3) Some register fields affect multiple pins at once. For example,
perhaps one register field affects both pin A8's an pin A7's mux setting
at once.
4) Depending on HW design, all register fields might be of type
described at (2) above, or all of the type described at (3) above, or a
mixture of both. Tegra is a mixture.
5) I expect the concept of a pin group to solely represent the various
groups of pins affected by each register field; in (2) above one pin per
group, in (3) above many pins per group.
Thus, to my mind, a pin group is purely a HW concept, and dictated
purely by HW design.
> Let's assume that unused pins are automatically configured as GPIOs in
> each configuration. The pin controller thus requires a second list of
> pins (for each of the modes), defining for which pins in each group it
> can grant gpio_requests in a given mode. Furthermore, the mmc node will
> have to "know" if mode "mmc2" or "mmc2_spi" must be selected for a given
> setup, making the thing somewhat unorthogonal.
The Linux pinctrl subsystem specifically doesn't provide mutual
exclusion between "mux function" and GPIO usage within a pin group,
although perhaps a driver could internally.
Consider a pin group in HW that encompasses 10 pins, but you've selected
a function onto it that only actually uses 6 pins for that logical
function. The other 4 pins aren't used, and can be GPIO. However, all
pins in the group are "claimed" because some mux function has been
selected onto the group that includes those 10 pins. In order to allow
some of those pins to be claimed as a GPIO, the pinctrl core simply
allows GPIO usage and mux function usage to be claimed on each
individual pin without regard for each-other.
Now, it would indeed be possible for each combination of (pin group, mux
function) to be associated with a list of pins from the group that could
be used as GPIO, and then for the pinctrl core to additionally enforce
that only those pins be claimed for GPIO usage. However, the pinctrl
core does not do this at present.
It's also a little difficult to completely validate that. Consider a mux
function that routes the pins to a HW module that considers some of the
signals to be optional. If one of those optional signals is used, then
the pin that would have carried it shouldn't be claimed as a GPIO, but
it the signal isn't used, then the pin will be free to use as a GPIO.
The selection of whether to use that optional signal may be outside the
realm of the pinctrl HW, i.e. in the HW module associated with the
selected mux function. Hence, pinctrl can't know whether the optional
signal is actually used, and hence can't conditionally allow it to be
used as a GPIO. To avoid pinctrl having to be completely nit-picky and
complex, it implements a simple approach and just allows absolutely any
GPIO/mux-function co-existence, with the expectation that if someone
attempts to use the HW incorrectly, it won't work, and they'll just fix
their SW/DT to actually request the correct configuration.
> When writing our pinctrl driver, my understanding was slightly
> different: I define seven pin groups:
> spi1 = {A5, A6, A7, A8};
> i2c = {A5, B5};
> mmc2 = {A1, B1};
> mmc4 = {A1, B1, C1, D1};
> mmc8 = {A1, B1, C1, D1, E1, F1, G1, H1};
> spi2 = {G1, G2, G3, G4};
> gpios = {A1, A5, A6, A7, A8, B1, B5, C1, D1, E1, F1, G1, G2, G3, G4, H1};
>
> Now each peripheral can individually request the pins it requires,
> independently of the others. Conflicts (e.g. between spi1 and i2c or
> between mmc4 and the GPIO at D1) are managed by the program logic in the
> pin controller. The advantages are the following:
> . The pin controller knows implicitly which pins are used for what and
> can easily grant or refuse pin and GPIO requests.
> . Conceptually, GPIO requests are now the same as any other
> configuration request.
> . The information of whether SPI2 is active or not is associated to
> spi2 and spi2 only. mmc does not need to know.
> . Implementation details of the pin controller hardware (which are the
> ports, which configuration to apply to a port to obtain a certain
> function) are confined in the pin controller driver.
I think that set of advantages is all true with the definition of a "pin
group" that matches exactly what groups exist in HW, i.e. the definition
I outlined above.
>> However, the connectivity between GPIO HW module "pins" (i.e. the GPIOs)
>> and pinctrl HW module "pins" (inputs to mux functions) is something that
>> only exists at the top-level of the SoC; outside the GPIO HW module
>> itself, and outside the pinctrl HW module itself.
>
> Well, in the case TB10x, GPIO pins are just the same as any other pins:
> They go through the pin controller all the same and there is really
> nothing that distinguishes them from, say, the mmc port in the example
> above - which can also be mapped either partially or completely. There's
> no bypassing of the pin controller going on at the top level or such.
I'd imagine that is true on most chips. It's certainly true on Tegra,
except for one minor irrelevant detail.
> And honestly: Have you ever seen a pin controller in which not only the
> program logic but also the pin data base can be reused from one SOC to
> another? At least I haven't.
Yes. A good few years ago I worked on some PPC chip where the pin
controller itself was 100% generic. It simply provided muxing for each
of N pins, each of which could have M mux functions (and indeed GPIO
controllers were one of those mux functions, for at least some of the
pins). From the pinctrl HW's perspective, the mux functions for each
pins were just "input 0", "input 1", ... "input n-1". A driver for such
HW would work no matter what SoC the pinctrl HW was placed into. The DT
binding would presumably just have pins labelled "0" .. "n-1" and mux
functions labelled "0" .. "n-1", and it would be up to the DT author to
consult each specific SoC's datasheet to determine which mux function
represented "MMC", "SPI", "I2C", ... for each pin. IIRC, IBM actually
had separate documentation for:
* The pinmux registers for muxing.
* The connectivity between the pinmux "pin-side" and the chip
pins/balls/pads.
* The GPIO registers.
* The connectivity between the GPIO controller's GPIO outputs, and the
pinmux HW's "mux-side" inputs, and similarly for all the other HW
modules that fed into the pinmux HW's muxes.
And honestly, I think likely all pinmux HW is this way. The only issue are:
* Datasheet authors tend to document the top-level connectivity of the
chip as if it were somehow part of the pinmux HW rather than actually
part of the top-level SoC routing.
* Some pinmux HW is designed to fit into a specific chip, so connect to
specific other HW modules, and hence not need to control every pin's mux
function independantly. This leads to "pin groups" where a single
register controls N pins at once. This reduces the number of registers
and amount of flop storage the pinmux HW needs. The exact trade-offs are
driven by the use-cases intended for the chip. This was the case on
Tegra20. However, this isn't very flexible, and requires significant
pinmux HW changes should the use-case change. I haven't actually talked
to the Tegra HW designers about this, but I strongly suspect that's why
Tegra30 now controls mux function individually per-pin, rather than in
use-case-targeted groups.
> On the other hand, For all Abilis chips,
> the program logic (the actual C functions) of the TB10x pinctrl could be
> reused with very minor modifications. It would be easy to extend the
> logic to a generic "Abilis pin controller" where all that needs to be
> changed in function of the "compatible" string is the pointer to the pin
> database.
>
>> In other words, you could have the exact same GPIO and pinctrl HW
>> modules instantiated into two different SoCs, but with completely
>> different mapping of GPIO IDs to pinctrl pin IDs.
>
> Well, you could very well conect a 4 bit mmc port instead of an spi in
> the above example without changing one thing in the pin controller or
> the mmc block...
Right. I expect that's all mostly true of many/most pinmux HW.
>> As such, it isn't even generally possible for the pinctrl HW module to
>> define pin groups that describe the mapping, because the mapping is not
>> a property of the pinctrl HW module, and hence should not be defined,
>> even partially, by the pinctrl HW module's driver.
>
> This is clearly implementation dependent. In the case of our chips, the
> opposite is actually the case:
>
> Your remark seems to reflect one of the following two hardware
> architectures:
>
> +- SPI
> Physical pins --- GPIO --- pinctrl -+- I2C
> +- mmc
(that's diagram 1)
>
> +- GPIO
> Physical pins -+ +- SPI
> +- pinctrl -+- I2C
> +- mmc
(that's diagram 2)
> TB10x hardware architecture:
>
> +- SPI
> Physical pins --- pinctrl -+- I2C
> +- mmc
> +- GPIO
(that's diagram 3)
No, I was thinking of diagram 3 above. I'm not sure if diagrams (1) or
(2) are common or exist? Certainly when I was contributing the Linux's
pinctrl SW design, I didn't really consider (1) or (2).
The issue is this: If the pinctrl and GPIO modules are separate modules,
then there is some wiring between them. Perhaps you're lucky and the
GPIO IDs end up exactly matching the mux-side pin IDs in the pin
controller HW. Perhaps that's not the case.
Now, inside the pinctrl HW, perhaps there's some other re-ordering;
perhaps the order of register addresses for mux functions doesn't match
the order of the datasheet's numbering of pins/bads/balls, or doesn't
match the HW block's numbering of the mux-side inputs.
So, there can be multiple levels of GPIO ID <-> pin ID mapping required.
My point is that:
Any mapping inside the pinctrl HW block is static and part of the HW
block's definition. This can be represented statically inside the
pinctrl driver source, or perhaps with some custom DT properties.
In that case, it /might/ be appropriate to define pin groups to help
define that mapping, since both pin groups and the mapping would be
strictly part of the internal HW definition of the pinctrl HW block.
Any mapping between the pinctrl HW and the GPIO HW is something at the
top-level of the SoC, and hence not something purely driven the the
pinctrl HW's.
In that case, the pinctrl driver or DT binding really shouldn't define
pin groups to help define that mapping, since the mapping is something
that exists outside the realm of the pinctrl HW block itself.
I would furthermore argue that the gpio-ranges DT property should be
only representing any mapping between the pinctrl and GPIO HW, not any
mapping inside the pinctrl HW.
However, I suppose I can see an argument that it might be useful to have
gpio-ranges represent the combination of *both* mappings as a single
mapping.
However, even in that case, I still don't think that the pinctrl HW
should be defining pin groups to help define that mapping. To do so
would encode information about the environment outside the pin
controller into the pin controller driver and/or DT binding, and that
information would not be purely driven by the pinmux HW itself.
And finally, I don't really like using pin groups for the purpose of
defining these mappings, since I intended them to purely represent the
mapping from register fields to the set of affected pins. However, I can
see an argument for doing this, since the pin groups are in fact still
representing /some/ aspect of the pinctrl internal HW.
>> In a similar fashion,
>> the DT binding for the pinctrl HW module should describe only the HW
>> module itself, and not the mapping/interaction with the outside world.
>> In other words, the DT binding for the pinctrl HW module also can't
>> define the names of any pin groups used in the GPIO<->pinctrl mapping,
>> for the same reasons.
>
> Except if this mapping is done _inside_ the pin controller, see above.
Yes, I got ahead of myself above. There are multiple places the mapping
could occur. Some would perhaps be appropriate to influence pin groups,
some not.
>> As such, I'm not sure that I conceptually agree with this patch series.
>>
>> Sure, it may make the gpio-ranges property more compact in some
>> (unusual?) non-linear cases. However, it's representing things
>> semantically incorrectly.
>
> Is it really in the TB10x case?
> To me it looks actually semantically more correct.
If they are purely representing a mapping internal to the pinctrl HW,
then it may be fine.
>> So, I'd like to question the motivation for using names here again.
>> Presumably the SoC vendor will write the gpio-ranges property for each
>> SoC, and put that into the SoC's .dtsi file. As such, no customer is
>> ever going to have to care about the property or its contents. So, I
>> don't really see how this helps you with your issue re: wanting to hide
>> details of multiple different ball-out options on similar SoCs, since
>> even with a manually-written purely numeric gpio-ranges property, all
>> that information is already essentially hidden; it's something that will
>> be written once, and then never looked at.
>
> Well, in the case of TB10x we are the SOC vendor and it was decided that
> all dts and dtsi files we publish are customer-facing data and must thus
> be coherent with the data sheet.
I would still tend to use gpio-ranges to represent the inter-module
connectivity, and use some alternative approach to re-jig that mapping
based on the mapping inside the pin controller.
For Tegra, I ended up choosing pinctrl pin IDs such that there was a 1:1
mapping between GPIO IDs and pinctrl pin IDs. I then ended up needing a
table that mapped pinctrl pin IDs (actually, the pin group IDs that
included those pins... and I would have needed this no matter what since
Tegra20 at least uses pin groups not per-pin configuration) to HW
register addresses. This is rather like saying that the pinctrl HW has
named inputs GPIO 0..n which are connected 1:1 with the GPIO HW module's
GPIO 0..n output signals, and then the pinctrl HW has a purely internal
mapping between the pinctrl HW module's GPIO signals and the pinctrl HW
module's pin/ball/pad-side pins.
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
