This patchset adds GPIO and pin controller drivers for the TZ1090, for both the general GPIOs/pins, and the low power (PDC) GPIOs/pins. LinusW: Please consider taking these for v3.11. The pinctrl ones need to go via your pinctrl tree due to the dependence on the new pinconf bindings. Changes in v3: - separated from irq-imgpdc and removed arch/metag changes to allow these patches to go upstream separately via the pinctrl[/gpio] trees (particularly the pinctrl drivers depend on the new pinconf DT bindings). - some s/unsigned/unsigned int/. - some s/unsigned int/bool/ and use of BIT(). - pinctrl-tz1090*: switch to generic pinconfig DT bindings and pinconf_generic_dump_config. - pinctrl-tz1090*: use tz1090, prefix for pins and function in DT bindings. - pinctrl-tz1090*: make internal functions static. - pinctrl-tz1090*: move initcall from postcore to arch. - gpio-tz1090*: refer to <dt-bindings/gpio/gpio.h> and <dt-bindings/interrupt-controller/irq.h> flags in bindings. - gpio-tz1090*: move initcall from postcore to subsys. - gpio-tz1090: add REG_ prefix to some constants for consistency. - gpio-tz1090: add comment to explain tz1090_gpio_irq_next_edge cunningness. Changes in v2: There've been plenty of changes since v1 (thanks for all the feedback!) so I think it's time for v2. I believe the only feedback not yet addressed is changing irq-imgpdc driver to use generic irqchip. - rebased on v3.10-rc2 - removed arch/metag/soc/ directory - removed arch/metag/include/asm/soc-tz1090/gpio.h - irq-imgpdc: use cached versions of irq_en and irq_route registers - irq-imgpdc: switch to using raw_spinlock - irq-imgpdc: (not had time to switch to generic irqchip yet) - add drive strength to generic pinconf debugfs output (patch 4) - add BIAS_BUS_HOLD generic pinconf (patch 5) - pinctrl-tz1090: switched to generic pinconf (a previous patch adds the BIAS_BUS_HOLD generic pinconf) - pinctrl-tz1090: changed device tree bindings to more closely match generic pinconf (separate tristate, pull-up, pull-down, bus-hold flags instead of pull=<X>, drive-strength measured in mA) - pinctrl-tz1090: removed "select" pinconf. Instead pins in a pin group have their own individual pin groups and can be individually muxed. Different pins in same pin mux group muxed to different functions is disallowed. Pin switched to peripheral mode when mux enabled. - pinctrl-tz1090: make use of BIT() from linux/bitops.h - pinctrl-tz1090: add a whole bunch of comments - gpio-tz1090: remove references to Linux flags in dt bindings - gpio-tz1090: make use of BIT() from linux/bitops.h - gpio-tz1090: make register accessors inline to match pinctrl - gpio-tz1090: update gpio-ranges to use 3 cells after recent ABI breakage - pinctrl-tz1090-pdc: switched to generic pinconf (a previous patch adds the BIAS_BUS_HOLD generic pinconf) - pinctrl-tz1090-pdc: changed device tree bindings to more closely match generic pinconf (separate tristate, pull-up, pull-down, bus-hold flags instead of pull=<X>, drive-strength measured in mA) - pinctrl-tz1090-pdc: make use of BIT() from linux/bitops.h - pinctrl-tz1090-pdc: add a whole bunch of comments - gpio-tz1090-pdc: remove references to Linux flags in dt bindings - gpio-tz1090-pdc: make use of BIT() from linux/bitops.h - gpio-tz1090-pdc: make register accessors inline to match pinctrl - gpio-tz1090-pdc: update gpio-ranges to use 3 cells after recent ABI breakage Cc: Grant Likely <grant.likely@xxxxxxxxxx> Cc: Linus Walleij <linus.walleij@xxxxxxxxxx> Cc: Rob Herring <rob.herring@xxxxxxxxxxx> Cc: Rob Landley <rob@xxxxxxxxxxx> Cc: devicetree-discuss@xxxxxxxxxxxxxxxx Cc: linux-doc@xxxxxxxxxxxxxxx James Hogan (4): pinctrl-tz1090: add TZ1090 pinctrl driver gpio-tz1090: add TZ1090 gpio driver pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver gpio-tz1090-pdc: add TZ1090 PDC gpio driver .../devicetree/bindings/gpio/gpio-tz1090-pdc.txt | 43 + .../devicetree/bindings/gpio/gpio-tz1090.txt | 87 + .../bindings/pinctrl/img,tz1090-pdc-pinctrl.txt | 130 ++ .../bindings/pinctrl/img,tz1090-pinctrl.txt | 232 +++ drivers/gpio/Kconfig | 14 + drivers/gpio/Makefile | 2 + drivers/gpio/gpio-tz1090-pdc.c | 243 +++ drivers/gpio/gpio-tz1090.c | 633 ++++++ drivers/pinctrl/Kconfig | 12 + drivers/pinctrl/Makefile | 2 + drivers/pinctrl/pinctrl-tz1090-pdc.c | 1029 ++++++++++ drivers/pinctrl/pinctrl-tz1090.c | 2077 ++++++++++++++++++++ 12 files changed, 4504 insertions(+) create mode 100644 Documentation/devicetree/bindings/gpio/gpio-tz1090-pdc.txt create mode 100644 Documentation/devicetree/bindings/gpio/gpio-tz1090.txt create mode 100644 Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt create mode 100644 Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt create mode 100644 drivers/gpio/gpio-tz1090-pdc.c create mode 100644 drivers/gpio/gpio-tz1090.c create mode 100644 drivers/pinctrl/pinctrl-tz1090-pdc.c create mode 100644 drivers/pinctrl/pinctrl-tz1090.c -- 1.8.1.2 -- To unsubscribe from this list: send the line "unsubscribe linux-doc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
