On Mon, Jun 10, 2013 at 10:21:00AM +0100, Srinivas KANDAGATLA wrote:
> This patch adds support to ASC (asynchronous serial controller)
> driver, which is basically a standard serial driver. This IP is common
> across all the ST parts for settop box platforms.
>
> ASC is embedded in ST COMMS IP block. It supports Rx & Tx functionality.
> It support all industry standard baud rates.
Your driver is not POSIX compliant.
> + for (; count != 0; count--) {
> + c = asc_in(port, ASC_RXBUF);
> + flag = TTY_NORMAL;
> + port->icount.rx++;
> +
> + if (unlikely(c & ASC_RXBUF_FE)) {
> + if (c == ASC_RXBUF_FE) {
> + port->icount.brk++;
> + if (uart_handle_break(port))
> + continue;
> + flag = TTY_BREAK;
> + } else {
> + port->icount.frame++;
> + flag = TTY_FRAME;
> + }
> + } else if (ascport->check_parity &&
> + unlikely(c & ASC_RXBUF_PE)) {
> + port->icount.parity++;
> + flag = TTY_PARITY;
> + }
> +
> + if (uart_handle_sysrq_char(port, c))
> + continue;
> + tty_insert_flip_char(tport, c & 0xff, flag);
> + }
> + if (overrun) {
> + port->icount.overrun++;
> + tty_insert_flip_char(tport, 0, TTY_OVERRUN);
> + }
No support for ignoring error conditions. No support for ignoring all
input... and:
> +static void asc_set_termios(struct uart_port *port, struct ktermios *termios,
> + struct ktermios *old)
> +{
> + struct asc_port *ascport = to_asc_port(port);
> + unsigned int baud;
> + u32 ctrl_val;
> + tcflag_t cflag;
> + unsigned long flags;
> +
> + port->uartclk = clk_get_rate(ascport->clk);
> +
> + baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
> + cflag = termios->c_cflag;
> +
> + spin_lock_irqsave(&port->lock, flags);
> +
> + /* read control register */
> + ctrl_val = asc_in(port, ASC_CTL);
> +
> + /* stop serial port and reset value */
> + asc_out(port, ASC_CTL, (ctrl_val & ~ASC_CTL_RUN));
> + ctrl_val = ASC_CTL_RXENABLE | ASC_CTL_FIFOENABLE;
> +
> + /* reset fifo rx & tx */
> + asc_out(port, ASC_TXRESET, 1);
> + asc_out(port, ASC_RXRESET, 1);
> +
> + /* set character length */
> + if ((cflag & CSIZE) == CS7) {
> + ctrl_val |= ASC_CTL_MODE_7BIT_PAR;
> + } else {
> + ctrl_val |= (cflag & PARENB) ? ASC_CTL_MODE_8BIT_PAR :
> + ASC_CTL_MODE_8BIT;
> + }
> +
> + ascport->check_parity = (cflag & PARENB) ? 1 : 0;
> +
> + /* set stop bit */
> + ctrl_val |= (cflag & CSTOPB) ? ASC_CTL_STOP_2BIT : ASC_CTL_STOP_1BIT;
> +
> + /* odd parity */
> + if (cflag & PARODD)
> + ctrl_val |= ASC_CTL_PARITYODD;
> +
> + /* hardware flow control */
> + if ((cflag & CRTSCTS) && ascport->hw_flow_control)
> + ctrl_val |= ASC_CTL_CTSENABLE;
This doesn't reflect those facts back into the termios structure to
indicate that they aren't supported.
Consider using uart_port's ignore and read status masks to implement
the break, framing, parity and overrun checking in your interrupt
handler using the same methodology as drivers like 8250, amba-pl011
etc. That will help you get these code sequences correct.
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
