Cleanup the text text describing the libata.force boot parameter and update the list of the values to include all supported horkage and link flag that can be forced. Signed-off-by: Damien Le Moal <damien.lemoal@xxxxxxxxxxxxxxxxxx> --- .../admin-guide/kernel-parameters.txt | 71 ++++++++++++++----- 1 file changed, 55 insertions(+), 16 deletions(-) diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt index 3f1cc5e317ed..30734a610b92 100644 --- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -2622,14 +2622,14 @@ when set. Format: <int> - libata.force= [LIBATA] Force configurations. The format is comma- - separated list of "[ID:]VAL" where ID is - PORT[.DEVICE]. PORT and DEVICE are decimal numbers - matching port, link or device. Basically, it matches - the ATA ID string printed on console by libata. If - the whole ID part is omitted, the last PORT and DEVICE - values are used. If ID hasn't been specified yet, the - configuration applies to all ports, links and devices. + libata.force= [LIBATA] Force configurations. The format is a comma- + separated list of "[ID:]VAL" where ID is PORT[.DEVICE]. + PORT and DEVICE are decimal numbers matching port, link + or device. Basically, it matches the ATA ID string + printed on console by libata. If the whole ID part is + omitted, the last PORT and DEVICE values are used. If + ID hasn't been specified yet, the configuration applies + to all ports, links and devices. If only DEVICE is omitted, the parameter applies to the port and all links and devices behind it. DEVICE @@ -2639,7 +2639,7 @@ host link and device attached to it. The VAL specifies the configuration to force. As long - as there's no ambiguity shortcut notation is allowed. + as there is no ambiguity, shortcut notation is allowed. For example, both 1.5 and 1.5G would work for 1.5Gbps. The following configurations can be forced. @@ -2652,19 +2652,58 @@ udma[/][16,25,33,44,66,100,133] notation is also allowed. + * nohrst, nosrst, norst: suppress hard, soft and both + resets. + + * rstonce: only attempt one reset during hot-unplug + link recovery. + + * [no]dbdelay: Enable or disable the extra 200ms delay + before debouncing a link PHY and device presence + detection. + * [no]ncq: Turn on or off NCQ. - * [no]ncqtrim: Turn off queued DSM TRIM. + * [no]ncqtrim: Enable or disable queued DSM TRIM. + + * [no]ncqati: Enable or disable NCQ trim on ATI chipset. + + * [no]trim: Enable or disable (unqueued) TRIM. + + * [no]trim_zero: Indicate if TRIM command zeroes data. + + * max_trim_128m: Set 128M maximum trim size limit. + + * [no]dma: Turn on or off DMA transfers. + + * atapi_dmadir: Enable ATAPI DMADIR bridge support. + + * atapi_mod16_dma: Enable the use of ATAPI DMA for + commands that are not a multiple of 16 bytes. + + * [no]dma_log: Enable or disable the use of the + READ LOG DMA EXT command to access logs. + + * [no]id_dev_log: Enable or disable access to the + identify device data log. + + * [no]log_dir: Enable or disable access to the general + purpose log directory. + + * max_sec_128: Set transfer size limit to 128 sectors. + + * max_sec_1024: Set or clear transfer size limit to + 1024 sectors. - * nohrst, nosrst, norst: suppress hard, soft - and both resets. + * max_sec_lba48: Set or clear transfer size limit to + 65535 sectors. - * rstonce: only attempt one reset during - hot-unplug link recovery + * [no]lpm: Enable or disable link power management. - * dump_id: dump IDENTIFY data. + * [no]setxfer: Indicate if transfer speed mode setting + should be skipped. - * atapi_dmadir: Enable ATAPI DMADIR bridge support + * dump_id: Dump IDENTIFY data. * disable: Disable this device. -- 2.35.1
